light GREAT WALL SO COOL 2006 Workshop Manual

B0-9
manual indoor plate
Electric indoor plate (Type A)
ten clips
12 clips
Vehicle Body
Front Door
12. Mount the interior trim panel of car door:

Dr)
(a) Connect the handle to the control lever first, then pull it
out from the indoor handle hole.
(b) Fix the clip by tapping to encase the interior trim plate of
car door in the corresponding hole of car door interior
panel.
(c) Use one screw to mount the inner clip.

Dr SF)
(a) Connect the handle to the control lever first, and then pull
it out from the indoor handle hole.
(b) Fix the clip by tapping to encase the interior trim panel in
the corresponding hole of car door interior panel
(c) Mount the inner clip with one screw; and
(d) Mount the electric switch and panel.

SL SK SY SJ)
(a) Connect the handle with the control lever first, then pull
out it from the indoor panel handle.
(b) Connect the plugging elements.
(c) Fix the clip by light tapping to encase the interior trim panel
of car door in the corresponding holes on indoor panel.
(d) Mount the inner clip with two bolts;
(e) Mount the four screws to fasten the interior trim panel of
car door, and cover the nuts.
(f) Mount the electric elevator switch.
13. Mount the indoor handle:
(a) Push the indoor handle into the car door paneling and
make it slide backward.
(b) Screw on the screws;
14. Mount the elevator handle (Dr)
Mount the paneling and elevator handle with spring snapping
ring under the condition the car doors and windows are closed
completely as shown in drawing.
12 clips
9. Adjust the car door and window glass;
Adjust the balance arm upwardly or downwardly until the
dimensions of A and B shown in drawing are equal, and then
fix the balance arm.
10. Mount the outer
Encase the claw of clip into the paneling seam and press the
outer on the paneling.
11. Mount the rear vision mirror
inner panel of electric door (type B)
four sets of bolt and nut
front

B0-20Vehicle Body
Adhesive Strip On Body Collision Avoidance
Adhesive strip of body collision avoidance
Notices on storing the adhesive strip of body collision avoidance:
1. The adhesive strip should be stored in the cool shadow place where can avoid the direct lighting of sun,
the high temperature and the dust.
2. As the adhesive strip is the PVC product, do not make it touch the paint thinner, other solvents and the
boiling water.
3. The limit storage period of adhesive strip is 9 months.
Element figure
exterior adhesive
strip at front doorexterior adhesive
strip at rear column
exterior adhesive
strip on wing panelexterior adhesive
strip at tailgateexterior adhesive
strip at rear body

B0-29
SJSJ
SJVehicle Body
Wheel-Trims Wrapping Angle and Exterior Trim Panel
Change of trim panel at front door
1. Tear down the trim panel at front door;
Prize up the clip of trim panel at front door and take down the
trim panel at front door. (SJ)
Uncover the luminous strip to tear down the five screws, then
open the front door and take down the trim panel at front door
after tearing down the five screws. (top-grade SY)
Change of front wrapping angle
1. Tear down the front wrapping angle;
Tear down the three screws and take down the front wrapping
angle and adhesive strip of wrapping angle lightly (there is two
screws in top-grade SY vehicle)
2. Mount the front wrapping angle
(a) Mount on the three screws (mount two screws for top-
grade SY vehicle)
(b) Contact the front wrapping angle with the front bar
closely, and the seam between the front wrapping angle
and the front Wheel-trims should be even with a smooth
transmission (by the way, the adhesive strip of wrapping
angle should be pressed tightly and evenly)
Change of front Wheel-trims
1. Tear down the front Wheel-trims
Tear down the four screws and the pressing plate of mudguard,
and take down the front Wheel-trims and adhesive strip of
Wheel-trims tightly (SY)
Tear down the five screws and the pressing plate of mudguard,
and take down the front Wheel-trims and adhesive strip of
Wheel-trims tightly (SJ)
Tear down the four screws and uncover the lighting channel of
the front Wheel-trims, take down the front Wheel-trims after
tearing down one screw (top-grade SY).
2. Mount the front Wheel-trims
(a) Flush the front end of front Wheel-trims with the lower
edge of wing panel; the adhesive strip of wheel-trims
should be pressed tightly and evenly. (SY)
Flush the front end of front Wheel-trims with the lower
edge of wing panel, the rear end of front Wheel-trims
with rear edge of wing panel. (top-grade SY SJ)
(b) Mount the four screws (five screws for SJ model) and the
pressing plate of mud guard and stick the lighting strip.
(top-grade SY)

B0-51Vehicle Body
Instrument Panel
Instrument Panel (
)
Element figure
SF
instrument panel body
lower instrument coverglove box
central panelcentral switchcentral air tunnel
combination instrument
instrument cover
cigarette lighter seat
ashtraycombined acoustic
deviceir-conditioner panel
fixed bracket

B0-52Vehicle Body
Instrument Panel
Instrument panel (
)
Element figure
SL SK SY SJ
instrument
panel body
right upper air tunnel
central air tunnel
left upper
air tunnel
combination
instrument
decorative cover
of instrument
lower covering board
at right end
glove box
lower instrument
cover(SY)
air-conditioning
controlling mechanism
assemblylower instrument cover
central cover
CD device
cigarette
lighter seat
lower decorative
frame of
instrument panel
ashtray cluster
glove box lock