display GREAT WALL SO COOL 2006 Service Manual

TF-5Transfer Box
Product Description and Simple Maintenance
Transfer Assembly NO. of Manufacturer
product assembly NO.
display
termnumber
displaythe last digit of the year
displaythe specific monthly
manufactuer data
displaythe month numnber
Example display:From January (A) to December (L)
Product instruction and simple maintenanceManufactuer data
Product instruction and simple mainte-
nance
1. Product Introduction
The transfer box adapted by our company is the transfer box
of 45-55 manufactured by Bogeguana, which is two-speed
and time driving, a set of planetary mechanism used is to
obtain the speed-reducing performance, while the driving
force is transmitted to the front driving gear by a highly precise
chain. The planetary gear train and rear output shaft element
of transfer box is lubricated initiatively through oil bath and oil
pump. This transfer box has four gears:

2H-stands for the two high gears
in which, only the two
rear wheel are driven, and the gear ratio of the transfer box
is 1:1


4H-stands for the four high gears, in which , all of the four
wheel are driven, and the gear ratio of the transfer box is
1:1


N- neutral location (this location only exists in the transfer
box of manual gearshift )
No driving force is transmitted
to the wheel when the input shaft and output shaft are
disconnected.

4L-stands for low gears, the four wheels are all driven, and
the gear ratio of transfer box is 2.48:1.
The gearshift of the mechanical gearshift transfer box is
obtained through the shifting-cam-type guide plate that is
operated by the shift rocker arm.
Sign board: which is fastened at the obvious external location
of transfer box, and on which the detailed data are marked.
borgwarner

TF-25
(b) Normal gear grinding trace.
Transfer Box
Washing, Checking, Up-Keeping and Exchanging (Checking)
Checking
1. Common Checking process
Check all parts by visual check to see whether there is damage
or serious or uneven wear (parts needed be substituted by new
parts such as O-ring, oil seal and etc. shall be excluded).
Abandon the damaged or weary parts that will affect on their
performance. The check items are as follows:

Burr: tips protruded from the material regionally

Rag: broken small blocks or particles

Crack: surface thread showing the material is partly or
completely separated.

Excessive abrasion
Refer to the serious or obvious abra-
sion beyond of application limit.

Reduction change
Material slip caused by the heavy
pressure on part of it.

adhesive bonding
Granules of the soft metal are dis-
persed and bonded on the hard metal surface.

Ditch trance: partial crack or trough that means the material
transfer instead of material loss.

Pitting corrosion
Damages to the metal surface caused by
pressure, which are displayed due to color change caused
by heat generated by metal friction.

Step wear
a weary step may be seen or felled between the
neighboring interface or between the non-touching face
due to the excessive wear.

Uneven wear: Partially, unevenly distributed wear, which
includes holes, bright spots, uneven polishing or other
visual drawbacks.
2. Gear or Chain sprocket tooth inspection
Check the gear and chain sprocket tooth according to the
following process:
(a) Normal gear shaving trace.
normal gear shaving trace
normal gear grinding trace

SA-12
6. Inspection and replacement for front brake disc
(a) Check the wear situation of the front brake disc. (see Dr
the brake caliper).
(b) Use the spanner to tear down the bolts that connect the
front wheel hub and the front brake disc.
(c) Connect the front wheel hub and the front brake disc with
bolt and spring washer, and screw up the bolts with a
moment spanner to the specified torque in the diagonal
order.
Fastening torque
(60-79)N
m
(d) Conduct the equilibrium test on the dynamic balancer,
the amplitude value displayed should not be larger than
13.5g under the condition that the measuring rotating
velocity is 796 r/m and the locking rotating velocity is
786 r/m, when the amplitude value is larger than 13.5 g,
encase the counter balanced clip, which is 4 g each, at the
corresponding phase, the number of the clip encased
should not be more than four.
7. Bearing outer race change
Press in the new bearing outer space with the special service
tools.
Notice: the bearing inner and outer races should be changed at
one time.
Assembly of Front Wheel Hub
1. Mount on the Bearing 32007 inner race and roller assem-
bly as well as the front wheel hub oil seal.
Coat the lithium base grease of (4-5)mm on the inner surfaces
of bearing outer race and the front wheel hub, encase the
Bearing 32007 inner race and roller assembly, plaster the
lubricant again. Coat a little lubricant on the lips of front wheel
hub oil seal and then tap it in place.
Notice: do not make the lubricant contact the front brake
disc face.
2. Mount on the Bearing 32007 inner race.
After coating the bearing outer race with the lithium base
grease of 4-5 mm, encase the inner race and roller assembly of
Bearing 30205, and plaster the lubricant again.
Suspension System and Automobile Axle (Dr/2WD)
Front Wheel Hub and Steering Knuckle (Front Wheel Hub)

SA-30
5. Front hub bearing outer race inspection and change
(a) Check each bearing
Wash the inner and outer races of each bearing, and check
them whether they are wearied or damaged.
(b) Tear down the outer race of each bearing.
Tap out the bearing outer race with copper bar and
hammer.
Notice: bind the dismantled inner and outer races of
bearing together to prevent from mixing.
6. Front brake disc inspection and change
(a) Check the wear situation of front brake disc.
(b) Tear down the bolts that connect the front wheel hub and
front brake disc.
(c) Connect the front wheel hub and front brake disc and
screw up the bolts with moment spanner to the specified
torque diagonally
Fastening torque
(70-80)N
m
(d) Conduct the dynamic balance test on the dynamic balancer,
the amplitude value displayed should not be above 13.5g
under the condition that the measuring rotating velocity
is 796 r/m and the locking rotating velocity 786 r/m,
otherwise, tap in the counter balanced clip, which is 4g
each, at the corresponding location, the number of the
clip should not be more than 4.
(e) Tap in the new bearing outer race with the special service
tool.
Notice: the inner and outer races of bearing should be
changed in set.
Assembly of Front Wheel Hub
1.Mount on the inner race and roller assembly of front hub
bearing (inner) as well as the front hub oil seal.
Coat the lithium base grease of 4 to 5 mm on the inside surface of
the bearing outer race and front wheel hub, and plaster the
lubricant in the front hub bearing (inner) and the roller assembly.
Coat a little lubricant on the lips of oil seal of front wheel hub, and
then tap the oil seal of front hub in place with special service tool.
Notice: do not coat the lubricant on the front brake disc face.
Suspension System and Automobile Axle (SF/2WD)
Front Wheel Hub and Steering Knuckle (Front Wheel Hub)

SA-46
5. Tear down the front hub, the oil seal and the inner race
of front hub bearing (inner)
(a) Prize out the oil seal.
(b) Take out the inner race of front hub bearing (inner).
6. Inspection on and change of the outer race of front hub
bearing
(a) Check each bearing:
Wash the inner and outer races of each bearing to check
their wear or damage situation.
(b) Tear down the outer race of each bearing:
Tap out the outer bearing race with copper bar and hammer.
Notice: bind the inner and outer races of the same
bearing together to prevent from mixing.
7. Inspection and change for front brake disc
(a) Check the wear situation of the front brake disc.
(b) Tear down the bolts that connect the front wheel hub and
the front brake disc.
(c) Connect the front wheel hub and the front brake disc with
bolts, which are tightened diagonally with moment span-
ner according to the specified torque.
Fastening torque
(70-80)N
m
(d) Make the dynamic balance test on the dynamic balancer,
and the amplitude value displayed should not be smaller
than 13.5g under the condition that the measuring rotat-
ing velocity is 796 r/m and the locking rotating velocity
of 786 r/m, otherwise, tap the counter balanced clip,
which is 4g each, in the corresponding position, the clip
number should not be more than 4.
(e) Tap in the new bearing outer race carefully with the
special service tool.
Notice: the inner and outer races of the same bearing
should be changed in one time.
Suspension System and Automobile Axle (SF/4WD)
Front Wheel Hub and Steering Knuckle (Front Wheel Hub)

BE-10Body Electric System
Protective Box Position Content
FuseVehicle
Model
1. Standby 30A
Standby 20A SJ
2. Standby 15A SY
Standby 10A SJ
3. Standby 10A SY SJ
4. Unload SY
Bass bubble 10A SJ
Power amplification 10 A top SY
5. Unload SY SJ
6. Unload SY SJ
7. Unload SY SJ
8. Air-conditioner 10A SY SJ
9. Charging 10A SY
Instrument 10A SJ
10. ECU 10A SY SJ
11. Back-up lamp 10A SY SJ
12. Cigarette lighter 30A SY SJ
receiver
13. Unload SY
Refrigerant 10A SJ top SY
14. Unload SY SJ
15. Steering electric window 10A SY
Humid display of steering 10A SJ
sindicating lamp
16. Stop lamp 10A SY SJ
17. Power aerial of inside lamp 10A SY SJ
18. Central control lock 20A SY SJ
19. Dual flasher 10A SY SJ
20. Front rain brush 10A SY SJ
21. Rear air-conditioner 15A SY
Unload SJ
22. Rear defroster 15A SY
Unload SJ
23. Rear rain brush 10A SY
Unload SJ
1Protective box I (continued)pv=pg
1
2
3
4
567
8
91011
12 13
14 15
16 17 18 19
20 21 22 23

BE-35Body Electric System
Combination Instrument
Common Troubleshooting
a. Such failures as inaccuracy indication, out-operation of indicator, on the fly of large and small summation meters
(mechanical wheel drive excluded) or incomplete liquid crystal display are caused by the interior failures of the
instrument, therefore, these failures, once occur, should be judged according to the instrument interior failures, and
change the combination instrument directly.
b. In case both the large and small summation meter and the indicator of electronic odometer are on the fly, such failures
can be removed by disassembling the speed sensor from the whole vehicle first, then connecting the sensor and
combination instruments as shown in the drawing.
Then, open the power supply and run the rotors quickly to observe the indicator variation of odometer.
the odometer indicator
should be no less than 40Km/
h variation in speed under
common condition whenrunning the rotors,
otherwise,
change with the good sensor
good combination instruments
vÉë
No
Yes
No
Yes
No
installation of sensorconnector for wiring harnessmalfunction of sensorfailure of instrument
panel connector for wiring
harness


12V

combination instrument




signal input
sensor

BE-36Body Electric System
Combination Instrument
Normal indicating range of combination instrument indicator
Speedometer
Real speed Km/h
Displayed speedKm/h
20 40 60 80 100 120 140 160
20
340
056005
Tachometer SY SL
800510005120061400716008
750 1000 2000 3000 4000 5000 6000
750
-10+201000-10+502000
120 3000
150 4000
200 5000
250 6000
300 Real rotating
speedr/min
Displayed rotating
speedr/min
Tachometer Dr SL SK SF
1000 2000 3000 4000 5000 6000 7000
1000
100 2000
200 3000
150 4000
200 5000
250 6000
300 7000
350 Real rotating
speedr/min
Displayed rotating
speedr/min
c. The inaccuracy display of tachometer is usually caused by the interior failures of tachometer, in such situation,
change the combination directly. As for the good-bad shift or out-operation of tachometer, the failures can be judged
according to the following approaches:
1) Start the vehicle, then check the voltage of signal input of tachometer (wire harness with multi-meter, the
voltage should be 6 V or so.
2) In case there is no signal voltage, check the power supply system of the whole vehicle to remove the failures
in circuit.
3) The plugs of wire harness is only allowed to be inserted in the combination instruments under the condition
that the signal voltage is normal, and the instrument is in normal operation.
4) Where the instrument is in abnormal operation, such trouble is caused by the failure of combination
instruments, in such case, change the combination instrument directly.
d. Troubles of fuel gauge and water thermometer
1) In case the instrument indicator points to the large number after it is powered, disconnect the sensor from the
plugging elements of wire harness before judging such kinds of troubles, if the indicator is still at large number,
it can be make a judgment that the trouble is caused by the interior failure of instrument, in such case, change
the combination instrument directly; if the indicator returns to the small number, according to which it can be
judged that the trouble is caused by the sensor failure, therefore, change the sensor directly.
2) where the instrument indicator stands still, such trouble may be caused by three causes probably, interior failure
of sensor, plugging elements of wire harness or interior failure of instrument; the inspection may be conducted
according to the following approaches: disconnect the plugging elements of wire harness from that of sensor,
grounding the wire at the sensor end; in such condition, the indicator should move upwardly to the largest
number; if such phenomena occurs, it can show the trouble is caused by the interior failure of sensor, in such
case, change the sensor directly; if the instrument indicator is still immobilized after it is powered, it can be
judged that the trouble is caused by the interior failure of instrument under the condition that the wire harness
and plugging elements are normal, in such case, change the combination instrument directly.
Fuel gauge Dr SF SY
Displayed oil
volume
Reference
resistance

Permitted
error
E 1/2 F
110 38 7

5
4+3
Fuel gauge SJ
Displayed oil
volume
Reference
resistance

Permitted
error
E 1/2 F
110 38 7

12
4
2
Fuel gauge SL SK
Displayed oil
volume
Reference
resistance

Permitted
error
E 1/2 F
120 45 17

10
10
10

BE-38Body Electric System
Backup Radar System
Inspection on Common Trouble
Failure Judgment Methods
No backup radar display (no
system start notification when
the reverse gear is engaged)Check whether the plugging elements of power supply
of back up radar control box are in well connection as
shown in drawing H in next page.(when the reverse
gear is engaged, touch the detector, if there is vibration,
which shows the detector is powered.
Check whether the wire harness of inner mirror in
electric room and that on the top of body are in well
connection as shown in the drawing A in next page
Check whether the wire harness of back up radar
control box is well connected with that of chassis
and that on the top of body.
Rotate the vehicle key to the ACC position and
engage the reverse gear, then measure to see whether
the back up power supply reaches to 12 V with the
multi-meter of 50 V of voltage, refer to the
red
and black
positions shown in the drawing in next
page.
If the voltage reaches 12 V, change the backup
radar control box in trial firstly, then the inner
mirror in electric room, finally change the roof
wire harness and the chassis.
No backup radar display (but
there is start notification when
the reverse gear is engaged)
remark: such trouble occur
under the blocking condition.Check whether the power supply of back up radar
is well located, see the red and position in the
drawing of next page.
Check and align the plugging element.Poor properties of ultrasonic wave
Change the ultrasonic detector heads.
Continuous back up radar red
lamp alarming (remark: there
is no obstacle within 0.5 m away
from the detector head)Check whether the detectors in the two circuit of
back up radar control box is well plugged, see the
marked positions F, G in the drawing of next page.
Check and well connect those plugging elements
Poor connection of the left/right ultrasonic detector head
Poor performance of back up radar control box.Check and well connect those plugging elements
Change the ultrasonic detector head
Change the back up radar control box.
Vehicle modelpc
Alarming by mistake
The rear standby tire is removedConduct the inspection operation for the rear
standby tire at the spacious place
fail to detect the obstacle
The detector head doesn
t workChange the detector head
There is dirt on detector headClean the detector head
Rear standby tire inspection1. engage the reverse gear for five times repeatedly within ten seconds at the spacious place so that the red
lamp on the screen flash three times, the system will automatically remember the standby tire status.
2. When the body height varies or the stand by tire is opened, make a new inspection for the rear stand by
tire to ensure the backup radar in normal operation.
Seven section of lamp display
Column I
1.49m-1.3m Column II
1.29m-1.1m
Column III
1.09m-0.9m Column IV
0.89m-0.75m
Column V
0.74m-0.6m column VI
0.59m-0.45m
Column VII

0.45m
Remark: the right and left LED display the direction and distance of obstacle respectively for driver
reference.If the voltage fails to reach 12 v, check the power
supply system of original vehicle
s large wires
to restore the voltage to 12 V.
Vehicle model SL SK
fail to detect the obstacle
Trouble description Repairing and treatment approaches

BE-61
Acoustical equipment system
The devices in this series is the vehicle-equipped acoustical receiver and recorder whose function is realized through
the electronic tuner and CD recorder, therefore, it can receive the amplitude modulation, frequency modulation and
stereo broadcast and can record the CD disc, what??s more, it is with the advanced electric anti-quaking, strong capability
of error correction, fashionable blue LCD liquid crystal digital display, and four-way power output. The device in this
series also has the characteristics such as low distortion, large output power and good performance of anti-interference,
broad frequency range and sweet sound, etc.
Diagram of Acoustical equipment system
SF
fuse
ignition switch
ACC ON ST
side-window aerial
CD deviceloudspeaker
ignition switch CD plugging elementplugging elements of rear
loudspeaker of CD device
1 2 3 4 5
6 7 8 9 1012 34
56 78912
34 5 5
4
1 2
3 5 3
8
4
9
75
6
1
7
Note: For Dr the antenna is the rod type.
battery cigarette lighter left front
right frontleft rearright rear
from small lamp relay
2
amplifier
Body Electric System
Acoustical Equipment System