gas type GREAT WALL SO COOL 2006 Service Manual

TF-9
5 4
3
1
6 2
1. rear body of transfer box
2. flange
3. oil seal
1. sensor bracket
2. bolt
3. speed sensor
4. o-ring
5. sensor assembly
6. bolt
7. gasket
8. rear body of transfer box2 1
5 3
4
4
6
7
8
Transfer Box
Disassembly of Transfer Box
4. gasket
5. nut
6. oil plug
Disassembly of Transfer Box
1. Brief instruction
In case the transfer box is required to be repaired for the
damaged specific element, it shall be taken apart to the degree
on which the damaged element is taken out. And the parts
taken apart from the transfer box, if it doesnít include the
damage element, can exist in the form of sub-assembly or
group instead the individual form, otherwise, the parts will be
taken apart individually.
2. Transfer Box Disassembly
Put the transfer box on the worktable and ensure the rear part
or the rear cover faces upward. Put the wooden block under the
front part of transfer box to keep the transfer box stands
horizontally. The disassembly process is as follows:
(a) Fasten the flange with the torque arm typed T-13-54-
002, screw off the nut to take down the gasket, then take
apart the flange and oil seal.
(b) Take down the two oil plugs from the transfer box body.
As for the electric gearshift transfer box, tear down the
electric shifting element according to the following
disassembly approach:
(a) Tear down the three bolts, gaskets, sensor and clip for
wire harness.
(b) Tear down the sensor assembly and take apart the O-
ring.
(c) Tear down the motor assembly.

TF-12
110
9
8
6
5
4
3
2
11
15
14
13
12
17
18
19
207
16
Transfer Box
Disassembly of Transfer Box
1. fork-type flange
2. dust cover
3. fork-type flange assembly
4. transfer box front housing
8. Take apart the following parts from the remaining trans-
fer box housing assembly
(a) Fasten the front fork-type flange with the torque arm of
T-13-54-002 and screw off the nuts to take apart the
gasket, pull out the front fork-type flange assembly and
sealing ring.
(b) The dust cover may also be pressed down from the front
fork-type flange where necessary, and
(c) Take apart the front output shaft.
1. planetary mechanism
assembly
2. gasket
3. snapping ring
4. thrust disc
5. sun wheel
6. planetary bracket
7. input shaft assembly
8. input shaft
9. needle bearing
10. bearing shell
11. transfer box front
body assembly
9. Tear down the front body, input shaft assembly and
planetary mechanism assembly
Tear down the following parts from the remaining transfer box
housing assembly
(a) Take apart the venting valve.
(b) Take apart the six bolts to separate the front body from
the transfer box housing and take down the front body
(take notice not to damage the front-end cover and the
transfer housing).
(c) Take apart the front body assembly, input shaft assembly
and planetary mechanism assembly in grouping manner
(loose the snapping ring to take apart the input shaft from
the front end cover).
(d) Hold one end of the input shaft on the worktable while
open the long end of the snapping ring, press the front
body tightly to disassemble the front body assembly from
the remaining assembly.
(e) Take apart the snapping ring and oil seal from the front
body, the pin is only be taken apart where change is
necessary.
(f) Take apart the bearing and gasket from the input shaft
assembly after the bearing gripping loop is taken apart;
and take apart the input shaft assembly from the planetary
mechanism assembly.
(g) Take apart the needle bearing and bearing shell from the
input shaft assembly, and
(h) Take apart the snapping ring, thrust disc and sun wheel
from the planetary assembly, and
(i) Do not try to disassemble the planetary bracket.
4
2
1
5 6
7
83
5. front output shaft
6. oil seal
7. washer
8. nut
12. oil seal
13. locating pin
14. transfer box front
body
15. snapping ring
16. transfer box front
housing
17. bearing
18. bearing gripping
loop
19. bolt
20. vent

TF-17
1.25-1.75mm
23
1
12.70mm
13
2
4
4
2
1
5 6
7
83
(e) In the case that the input shaft is taken apart, what need
to do is to fill the needle bearing as shown in the drawing
and press it in the input shaft, meanwhile, press the new
sliding bearing to complete the whole input shaft assembly.
(f) Raise the planetary mechanism assembly to mount it into
the input shaft assembly; encase the thrust gasket and
press in the bearing through the input shaft end. Encase
the fixed bearing in the snapping ring groove of the input
shaft with a snapping ring.
(g) If the transfer box front body is taken apart, press the new
located pin in the front body, and the pressing dimensions
are shown in the drawing.
(h) Put down the oil seal as the drawing shows, and press it
in the front body according to the dimensions shown in
the drawing.
(i) Put down the front body assembly on two wooden blocks
in the way that the coupling face of the front body and the
housing faces upward, so that there is clearance left
between the input shaft assembly and the worktable. Put
down the input shaft and planetary mechanism assembly
in the front body, in which the input shaft shall be
downward. Open the long ends of the snapping ring to
encase input shaft and planetary mechanism assembly
until the snapping ring enters into the external snapping
ring groove of the bearing.
(j) Coat the sealing glue of 1.6mm on the coupling locations
of the front end cover and transfer box assembly, The
glue shall be coated continuously without break and steer
clear of the screwed hole.
(k) Screw up the six bolts.
Fastening torque
(27
46)N
m
6. Assembly of front output shaft
Mount the following parts:
(a) If the dust cover is taken apart, mount it by pressing.
(b) Encase the input shaft, sealing ring, gasket and nuts in the
transfer front housing.
(c) Insert the torque arm of T-13-54-002 in the flange hole to
screw up the nuts.
Fastening torque
(203
244)N
m Transfer Box
Transfer Box Assembly
1. needle bearing
2. bearing roller
3. input shaft
1. locating pin
2. oil seal
3. front body of transfer box
4. snapping ring
1. fork-type flange
2. dust cover
3. fork-type flange assembly
4. transfer box housing5. output shaft
6. oil seal
7. washer
8. nut

SA-4Suspension System and Automobile Axle
Alignment of Front Wheel (Dr SL SK SY SJ)
5. Adjustment for inner tilt angle of kingpin, outer tilt angle
of front wheel and back tilt angle of kingpin
Item
Inner tilt
angle of
kingpin
Outer tilt
angle of
front
wheelApplicable vehicle type
Dr SL SK SY
SJ
Mechanic
steeringDr SL SK SY
Power
steeringDr
SL SK SY
SJ
Back tilt
angle of
kingpinMechanic
steeringDr SL SK SY
Power steer-
ingDr SL SK SY
SJ9
30
45

14
52

0
30
20

0
10
10

0
20
10

0
30
15

2
45
15

3
15
Location parameter
4. Adjust the wheel angle
Take apart the limit bolts of the steering knuckle to check the
steering angle A of inner wheel.
Inner wheel steering angle
Dr SL SK SY
( 36
40
)
SJ
( 32
34
)
Remark: The wheel should not contact the body or brake hose
when the steering wheel reaches the limit position.
In case the steering angle of inner wheel doesnít conform to the
standard value, adjust the wheel angle through adjusting the
limit bolts of the steering knuckle.
Fastening torque
(90
0)N
m(SJ)
If the wheel angle fails to be adjusted within the standard value,
change the weary or damaged parts of steering system.
If the tilt angle fails to fall within the specified values, make an
adjustment through adding or reducing the gaskets on the
location of upper arm.
Gasket thickness: 3.0, 2.0 and 1.0mm
Once the gasket thickness increases by 1mm, the outer tilt
angle of wheel will change by 7', while the back tilt angle of
kingpin will change 20'.
After the wheel outer tilt angle and the back tilt angle of kingpin
are adjusted, if the inner tilt angle of kingpin still fails to the
specified value, check the steering knuckle or front wheel to
see whether they are bending or loose.
1
50
-20

adjusting bolt
outer tilt
angle of
front wheel inner tilt angle of kingpin
back tilt angle of
kingpin
front AB AB
HPM

AC-2Air Conditioning System
Introduction
In case the liquid refrigerant enters into the eye or touches the
skin, the following measures shall be taken:

Wash the part where is touched by the refrigerant with a
great deal of water.

Coat the skin with the clean Vaseline.

See the doctor or go to the hospital for treatment; and

Do not try to cure it yourself.
General Introduction
1. Take notice when handling refrigerant General Introduction
(a) Do not handling with refrigerant in the closed room or
near to open fire.
(b) Safety goggles shall be worn when handling
(c) Be careful to avoid the liquid refrigerant from entering
into your eye or touching you skin.
waterair
dust
ÅçåÇÉåëÉêplug
2. Take notice when changing the parts of refrigerant pipes:
(a) The refrigerant shall be exhausted gradually before
changing.
(b) The dismantled parts shall be covered with plug right
away so as to prevent the water or dust from entering into
the system.
(c) Do not store the condenser or liquid tank under the
condition that the plug has been uncovered. and
(d) Refrigerant shall be exhausted before installing the new
condenser, because the refrigerant, if not exhausted, will
eject out in gaseous form with the lubricant oil when the
plug is moved away.
3. Take notice when fastening the connection parts:
(a) Spread a little lubricant oil at the matching position of the
O-type ring to fasten the connection and avoid of gaseous
refrigerant leakage.
(b) Fasten the nut with two spanners so as to avoid of the pipe
deformation.

AC-3Air Conditioning System
Introduction
(c) Tighten the O-ring matching position or the threaded position
to the specified moment.
4. Take notice when connecting measuring meter at branch pipes:
(a) Connect the end of filling hose with high speed joint to the
filling valve of compressor.
(b) Letter
D
marked on the compressor near the auxiliary valve
represents the side of high voltage while
S
means the side of
low voltage, which shall be looked out when connecting the hose.
(c) Fasten the bolts by hand, and
(d) In order to prevent the hose from loosing, lubricant oil shall not
be spread at the connection position.
Remarks: after connecting the measuring meter on branch pipes to
the refrigerant container (repairing tank), the air in the hose shall be
exhausted up.
5. Take notice when vacuumizing:
After vacuumizing for 20 min, maintain the container at certain
pressure to ensure that all air in it is exhausted up, and another
inspection shall be made to see whether there is leakage.
6. Take notice when handling with the refrigerant container
(repairing tank):
(a) Do not heat it.
(b) Store the container at the place where temperature is under 40

(c) In case of heating the repairing tank with hot water, care shall
be paid to the valves at the top of tank, do not dip them into the
water, or the water will penetrate into the cooling system.
(d) The empty repairing tank is forbidden to reuse.
8. Take notice when using the high-pressure air cylinder type
inspecting device:
(a) In case the open fire is used, it is the first to ensure before using
there is no flammable material around.
(b) Be careful because toxic gas will be produced when the
gaseous refrigerant meets with the open fire. 7. Take notice in the A/C operation or when adding the liquid
refrigerant:
(a) In case the gaseous refrigerant in the cooling system is
insufficient, which can lead to the compressor burns out, and
such accidents shall be avoided.
(b) If the valve on the side of high pressure is uncovered, the
refrigerant will flow in the reverse direction, which may lead
to the break of the repairing tank, therefore, only valves on the
side of low pressure are allowed to open or closed.
(c) If the repair tank is laid in reverse direction, and the refrigerant
is added in liquid status, the liquid refrigerant will be
compressed, which may lead to failure of the compressor,
therefore, refrigerant shall be inflated in the gaseous status.
(d) Be careful not over-inflate the gaseous refrigerant, otherwise,
such failures as insufficient cooling, increase of oil consuming
or over heat of engine will be followed.
under 40

incorrect
correct
measuring meter of branch pipe
loose over-fastened
A/C operation