height adjustment GREAT WALL SO COOL 2006 Service Manual

CL-3Clutch
Inspection and Adjustment of Clutch Pedal, Air Exhausting of Clutch
Air-exhausting of clutch
Remark: in case operation needs to be conducted for the clutch
system or if there is air in clutch, exhaust the air.
Notice : Do not stain the painted surface with brake liquid,
if any brake liquid is left, wash it away immediately.
1.
Fill the brake liquid into the oil cup of clutch master cylinder;
The oil cup of master cylinder shall often be checked and, if
necessary, added with brake liquid.
2.
Connect the ethene resin pipe to the air-exhausting valve.
Insert the other end of the pipe into the container, half of which
is filled with brake liquid.
3. Air-exhausting in clutch system
a) Move the clutch pedal up and down slowly for several times.
b) Loosen the air-exhausting valve when pressing the pedal
increasingly until there is brake liquid overflowing, then
tighten the air-exhausting valve.
c)
Repeat this operation until the bubble in brake liquid disappears.
Inspection on and adjustment
of clutch pedal
1. Check whether the pedal height is correct
Pedal height that begins from front wall board:
Dr SF
(165
5)mm
SL SK SY SJ
(190-200)mm
2. Adjust the pedal height where necessary
Loosen the locking nut and screw off the adjusting bolts until
the pedal height is correct. Then screw up the locking nut.
Pedal free stroke
3. Check whether the pedal free stroke is correct
Press the pedal lightly until the resistance generated by clutch
occurs.
pedal free stroke: (5-15)mm
4. Adjust the pedal free stroke where necessary;
a) Loosen the locking nut and rotate the push-rod until the
stroke is correct;
b) Screw up the locking nuts;
c) Check the pedal height after the adjustment of pedal free
stroke.
adjusting spot in
pedal height
pedal height
pedal free stroke

SA-5
7. Check the sliding measuring situation.
Check the sliding situation with the sliding measuring tester.
Sliding measuring value:
.5m/km
push forward the vehicle;
forward
A=BB A
6. Wheel toe-in adjustment
(a) Verify that each wheel has been located forward in a line.
(b) Mark the tire center at the bearing height on the tread of
left and right tire, and measure the distance between the
marks on left and right treads.
(c) Push forward the vehicle until the mark on the back tread
of tire moves to the front.
Remark: the toe-in measurement should be conducted from the
same spot at the same height.
(d) Measure the distance between the two marks on the front
of two treads.
Toe-in value: (0-2)mm
(e) Loosen the clamping bolts of connecting pipe.
(f) Adjust the toe-in angle through the approach according to
which rotate the left and right drag rod tube by a same
angle.
Remark: check the lengths of the two drag rods to see whether
the two rods are same in length.
Length error of the left and right drag rod should not
be larger than 2.0mm.
(g) Tighten the clamping bolts.
Fastening torque
(20
) N
m
(h) Locate the split pin well.
Suspension System and Automobile Axle
Alignment of Front Wheel (Dr SL SK SY SJ)

SA-6Suspension System and Automobile Axle
Alignment of Front Wheel
Alignment of Front Wheel (SF)
Alignment of Front Wheel
(SF)
1. The following items should be checked to remove the
troubles.
(a) Check the tire abrasion and the air inflation to see it is
suitable or not.
Tire inflation pressure: (250
0)kPa
(b) Check the front wheel bearing to see whether it is loose.
(c) Check the front suspension to see whether it is loose.
(d) Check the steering driving device to see whether it is
loose, and
(e) Check the front vibration through elastic force test to see
whether it is normal in performance.
2. Height adjustment of vehicle
Adjust the vehicle height to the standard value so as to make
the Alignment of Front Wheel inspection.
A-B-58 5mm
A: The height of steering knuckle shaft center.
B: The center height of the adjusting cam bolt at front end
The standard value for the unloaded height is: the
difference of the center height of drive shaft climax and
the front adjusting cam bolt is 58.5mm.
3. Mount on the four wheel locating device
This approach should be conducted according to the detailed
instruction of the equipment manufacturer.
4. Adjust the outer tilt angle of front wheel and the back tilt
angle of kingpin
The outer tilt angle of front wheel: 0
5'
0'
The back tilt angle of kingpin: 2
0'
0'
Outer inclination of front wheel:
BA
the outer tilt angle of
front wheelthe back tilt angle
of kingpin
front

BR-5Braking System
Inspection and Adjustment
pedal push rodbraking lamp switch
pedal push-rod
free stroke of
pedal: (3-6) mm
Inspection and adjustment
Inspection on and adjustment of brake pedal
1. Check the pedal height as shown in the drawing to
whether it is correct,
The height from the pedal to the front floor:
Dr SF
160mm
SL SK SY SJ
(190-200)mm
2. Adjust the pedal height if necessary:
(a) Loosen the locking nuts of braking lamp switch;
(b) Loosen the braking lamp switch to the most degree.
(c) Loosen the locking nuts of drag rod;
(d) Adjust the pedal height through rotating the pedal drag
rod;
(e) Rotate the stop light switch reversibly until it contact
with the stop baffle of pedal.
(f) Screw up the two locking nuts.
(g) Check the braking lamp is lightened or not when tread
down the brake pedal.
(h) Check and adjust the pedal free stroke after adjusting the
pedal height
QKAdjust the free stroke of pedal if necessary:
(a) Loosen the locking nuts of the pedal drag rod and rotate
the pedal drag rod to adjust the pedal free stroke.
(b) Start the engine to confirm the free stroke.
(c) Check the pedal height after adjusting the pedal free
stroke. 3. Inspection on Pedal Free Stroke:
(a) Stop the engine working and tread down the brake pedal
several times until the vacuum booster is not in the stage
of vacuum.
(b) Tread down the pedal until the resistance occurs, and
measure the distance shown in the drawing.
Pedal free stroke
(3-6)mm
pedal height