length GREAT WALL SO COOL 2006 Service Manual

PR-2Drive Shaft
Notice and Troubleshooting
Notice
Notice: do not grip the drive shaft sleeve too tight with vice
so as to avoid the deformation.
troubleshooting
Trouble Causes Resolving approaches
Noise Wear of universal joint yoke spline;
Wear of central bearing;
Wear or seize-up of cross shaft bearingChange the drive shaft;
Change the central bearing;
Change the bearing of cross shaft
Vibration Oscillation difference of the drive shaft;
Drive shaft imbalance;
Wear of the liner of rear bearing in the lengthening shell of
gear box;
Spline seize-up of the universal joint yokeChange drive shaft
Change drive shaft
Change the liner
Change drive shaft

SA-5
7. Check the sliding measuring situation.
Check the sliding situation with the sliding measuring tester.
Sliding measuring value:
.5m/km
push forward the vehicle;
forward
A=BB A
6. Wheel toe-in adjustment
(a) Verify that each wheel has been located forward in a line.
(b) Mark the tire center at the bearing height on the tread of
left and right tire, and measure the distance between the
marks on left and right treads.
(c) Push forward the vehicle until the mark on the back tread
of tire moves to the front.
Remark: the toe-in measurement should be conducted from the
same spot at the same height.
(d) Measure the distance between the two marks on the front
of two treads.
Toe-in value: (0-2)mm
(e) Loosen the clamping bolts of connecting pipe.
(f) Adjust the toe-in angle through the approach according to
which rotate the left and right drag rod tube by a same
angle.
Remark: check the lengths of the two drag rods to see whether
the two rods are same in length.
Length error of the left and right drag rod should not
be larger than 2.0mm.
(g) Tighten the clamping bolts.
Fastening torque
(20
) N
m
(h) Locate the split pin well.
Suspension System and Automobile Axle
Alignment of Front Wheel (Dr SL SK SY SJ)

SA-8Suspension System and Automobile Axle
Alignment of Front Wheel (SF)
(c) Mark the center of the back of front wheel, and measure
the distance ìBî between the remarks on the left and right
tires.
(d) Push the vehicle forward so that the mark on the back of
tire moves to the measuring height of the instrument.
Remark: if the tire moves too far, repeat the approach (b).
(e) Measure the distance ìAî between the marks on the front
of tire.
(f) Measure the wheel toe-in.
Toe-in = B-A
Inspection standard: (0-2)mm
In case the toe-in fails to conform to the specified value, it can
be amended through adjusting the left and right drag rods.
(g) Loosen the clamping bolt and nut.
(h) Adjust the toe-in situation by the approach of rotating the
left and right drag rod by a same angle.
(i) Ensure the left and the right drag rods are same in length.
B
forward
move the vehicle forward
A
front
A
B
A=B

SA-19
Torsion Rod Spring
Dismantle of Torsion Rod Spring
1. Use the jack to raise up the frame and support it with the
bracket.
2. Take apart the locking nuts to measure the length of the
projecting end of the bolts, as shown in the drawing.
Remark: This measuring value can be referred when adjusting
the chassis ground clearance.
3. Take apart the dust cover.
4. Loosen the regulating nut until there is no tension on the
torsion rod spring.
5. Take apart the torsion arm, torsion rod spring and the
torsion regulating arm.
(a) Tear down the mounting nuts of the torsion rod arm.
(b) Take apart the torsion regulating arm from the adjusting
bolt, the torsion regulating arm should be taken apart with
the torsion rod spring and the torsion rod arm together.
Dr SL SK SY
SJ
SFSuspension System and Automobile Axle (Dr/2WD)
Front Suspension (Torsion Rod Spring)

SA-20
(f) Screw up the adjustable nuts so that the protruding length
of the bolt is equal to that before tearing down.
(g) Mount on the wheel and dismantle the bracket, bounce
the vehicle several times so as to make the suspension in
place.
(h) Screw up the adjustable nut to regulate the ground
clearance.
2. Tighten the locking nuts according to the specified torque.
Tighten torque
(83
5)N
m
3. Mount on the dust cover.


Mount of Torsion rod Spring
Notice: the torsion rod spring marked with
L
(left) or

R
(right), do not mount the springs at the incorrect
location.
1. Mount the torsion rod spring, pedestal arm and torsion arm;
(a) Coat the lithium base grease on the spline of torsion rod
spring.
(b) Align the wide-teeth parts and then mount the pedestal
arm on the torsion rod spring.
(c) Align the wide-teeth parts and then mount the torsion arm
on the torsion rod spring.
(d) Mount the torsion rod spring on the side of torsion arm
and mount on the pedestal arm on the adjusting bolts.
(e) Screw up the torsion arm nuts according to the specified
torque.
Fastening torque
(83
)N
m Suspension System and Automobile Axle (Dr/2WD)
Front Suspension (Torsion Rod Spring)
front

SA-100Suspension System and Vehicle Axle
Rear Suspension (Leaf Spring Type)
Remark: Tightening U-shaped bolt to the degree that the
protruding lengths of all U-shaped bolts under the spring seat
are the same.
3. Mount the rear vibration damper
(a) Connect the vibration damper to the vehicle frame with
bolts and then tighten the bolts.
Tightening moment: (25
)N
m
(b) Connect the vibration damper to the sprint seat with bolts
and tighten these bolts.
Tightening moment: (25
)N
m
4. Keep the suspension frame in stable status;
(a) Mount on the wheel;
(b) Remove the bracket, and make the vehicle bounce verti-
cally for several times so as conduce it in stable status.
5. Tighten the front ear pin and rear ear pin;
Tighten the nuts of front ear pin;
Tightening moment: (90
0)N
m
Tighten the nuts of rear ear pin;
Tightening moment: (90
0)N
m
all lengths of bolts protruding are same

BR-9Braking System
Master Cylinder
Mount of Master Cylinder
1. Adjust the length of vacuum booster pushrod before
mounting the master cylinder;
2. Mount the master cylinder:
Mount the master and sealing washer on the vacuum booster
with four nuts.
3. Connect the two pipelines of braking system;
Mount the brake pipeline on the master cylinder with SST and
screw up the nuts.
Fastening torque

Dr SF
(18
2)N
m
SL SK SY SJ
(19
1)N
m
4. Connect the alarm switch joint for liquid level;
5. Fill the oil cup with brake liquid and exhaust the air in
the brake pipeline;
6. Check to see whether there is brake liquid leakage;
7. Check and adjust the brake pedal.
SST
SST

BR-11Brake System
Vacuum Booster
Inspection on Vacuum booster parts
Operation for one-way valve inspection
(Gasoline engine)
(a) Tear down the one-way valve;
(b) Check the air to see whether it flows from the vacuum
booster side toward the engine side.
(c) Check the air, change the one-way valve if the air flows
from the side of engine toward the vacuum booster.
(d) Mount the one-way valve in the right place.
(a) Tear down the one-way valve from the vacuum pipe.
(b) Check the air to see whether it flows from the side of
vacuum room to the hose.
(c) Check the air, and change the one-way valve if the air
flows to the hose to the vacuum room.
air
engine side booster side
air airless
air
hose side vacuum side
airairless
Mount of Vacuum Booster
1. Adjust the length of vacuum booster pushrod:
(a) Mount the sealing washer on the master cylinder;
(b) Put SST on the sealing washer and descend the pin rod
until it contact lightly the piston with its top;
(c) Put top of SST downward ,and mount it on the vacuum
booster.
(d) Check the clearance between the vacuum booster pushrod
and the head of pin on SST.
(e) Adjust the length of vacuum booster pushrod until the
pushrod touches the pinhead.
2. Mount the vacuum booster, sealing washer and Ushaped
clip head.
(a) Mount the vacuum booster and sealing washer.
(b) Mount the U-shaped clip head.
(c) Mount and tighten the assembling nuts of vacuum booster.
3. Connect the U-shaped clip head and the brake pedal:
Encase the U-shaped clamping pin in the hole of U-shaped clip
head and the brake pedal, and then mount the spring pin on the
U-shaped clamping pin.SST
washer
SST
(Diesel engine)

BR-32
8. Mount on the adjuster;
Poke the brake shoes with the screwdriver and then mount the
adjuster.
9. Mount the brake shoe retainer ring, bracing wire of
guide seat, self clearance-adjusting bracing wire and
the return spring.
(a) Mount the brake shoe retainer ring, then the front return
spring.
(b) Mount the return spring ,and then mount the forward
return spring.
10. Mount the self-clearance toggle plate:
(a) Mount the toggle plate bracing wire torsion spring on the
rear brake shoe.
(b) Mount the clearance self-adjusting toggle plate and hook
It with the clearance-adjusting bracing wire.
(9) Hook the self clearance-adjusting toggle plate with the
bracing wire torsion spring
11. Check the operation of self-adjusting mechanism.
(a) Drag the clearance-adjusting bracing wire backward as
shown in the drawing, then release it. Check the clear-
ance-adjusting bolts to see whether it is rotating. If not,
check the rear brake to verify which part has problem.
(b) Adjust the clearance adjuster to shorten its length as
possible as can.
(c) Mount the brake drum
forward
Braking System
Rear Brake (DR)

BR-40
7.Mount the front brake shoe:
(a) Mount the lower tension spring between the front shoe
and the back shoe.
(b) Mount the front brake shoe in such manner that the end
shoe is inserted in the wheel-brake cylinder, and mount
correctly the adjuster.
(c) Mount the pressure spring, pressure spring cap and
claming pin.
Notice: Do not let the oil or lubricant touch the brake
shoe.
(d) Mount the upper tension spring.
8. Check the operation of self-adjusting mechanism.
(a)Move the parking brake lever of rear brake shoe forward
and backward as shown in the drawing, check the self-
adjusting screw arbor to see whether it can rotate or not,
if not, check the rear brake to see which part has problem.
(b) Adjust the adjuster length and shorten it as can as possible.
(c) Mount the brake drum.
(d) Drag the parking brake lever to the max distance until no
quack-quack is heard. Braking System
Rear Brake (SF)