oil filter GREAT WALL SO COOL 2006 Service Manual

TF-11
5. Tear down the Chain drive system
Take apart the following parts from the transfer box housing
assembly.
(a) Take apart the snapping ring and washer from the front
output shaft.
(b) Take apart the driving chain sprocket, driven chain
sprocket and drive chain together from the two output
shafts.
(c) Separate the chain sprocket from the chain.
12
345
6 7
1. output shaft
2. driving chain sprocket
3. driven chain sprocket
4. washer
12 34
5
6 7
6. Oil pump assembly
Take apart the shaft and pump assembly, pipe clip, oil pipe and
filter from the remaining transfer box housing assembly.
1
2
7
6 3
4
5
8 1. deceleration gear hub
2. inserted face of Shift
toggle fork
3. plastic sleeve
4. contact roller
5. pin
6. pin, contact roller and sleeve assembly
7. deceleration shift toggle fork
8. deceleration shift toggle fork assembly7. Deceleration shifting element disassembly
Tear down the following parts from the remaining transfer box
housing assembly.
(a) Take apart the deceleration hub, and deceleration shift
fork assembly from the housing.
(b) Take apart two plastic inserted faces from the decelera-
tion shift fork assembly
(c) Disassembly the deceleration shift fork assembly only if
it were broken.Cut the plastic cover,and take out the pin
and truckle. Transfer Box
Disassembly of Transfer Box
1. output shaft
2. driving chain sprocket
3. driven chain sprocket
4. washer
5. snapping ring
6. transmission chain
7. front output shaft5. snapping ring
6. transmission chain
7. front output shaft

TF-18
1. deceleration gear
2. output shaft
3. insert face of toggle fork
4. deceleration toggle fork assembly
5. pin, contact roller and sleeve assembly
6. deceleration shift toggle fork
7. plastic sleeve
8. contact roller
9. pin
12
6
7
8
9 3
NO PQ
R
S T
Transfer Box
Transfer Box Assembly
7. Deceleration shift parts assembly
The mounting process is as follows:
(a) If the parts are taken apart for change, assemble the shift
toggle fork assembly with a new pin-contact roller
assembly. Press the pin-contact roller in the deceleration
fork hole until the detent passes the hole completely and
seizes the right location. Ensure that the contact roller can
run freely.
(b) Mount two inserted faces of toggle fork on the decelera-
tion toggle fork assembly.
(c) Engage the deceleration fork assembly and deceleration
gear sleeve and put them in the housing, and the decelera-
tion gear sleeve shall be put in the planetary mechanism
assembly that is assembled already. Mount the rear
output shaft and joint the bearings at the ends of output
shaft and input shaft as well as the spline of the gear
sleeve.
Remarks: the output shaft assembly can be delayed until the oil
pump is mounted on the output shaft. The oil pump may be
dipped into the lubricant through the oil pump screen, turn the
output shaft in clockwise from the output shaft direction to see
whether there is lubricant pumped out so as to check whether
the oil pump can work normally or not. The parts mounted
readily may be encased in the transfer box housing as an
assembly
8. Oil pump assembly
Ensure the parts of oil pump are completely lubricated when
assembling, and the oil can be pumped out from the conical
hole of the oil pump front cover. The mount of oil pump is as
follows:
(a) Mount the pin on the rear output shaft.
(b) Slide the oil pump assembly on the rear output shaft
along with the pin.
(c) Put the gripping hoop at the end of oil pipe that is
mounted on the oil nozzle of the pump housing, screw up
the gripping hoop.
1. filter
2. oil pump hose
3. gripping hoop
4. oil pump assembly
5. output shaft
6. pump pin
7. output shaft and pump assembly5
4

BR-8Braking System
Master Cylinder
Master Cylinder
Disassembly of Master Cylinder
1. Tear down the alarm joint for liquid level;
2. Exhaust the brake liquid with the injector:
Notice: brake liquid must not be left on the paint surface,
if any, clear it away.
3. Tear down the pipeline of braking system;
Tear down the pipeline of braking system from the master
cylinder with SST.
4. Take apart the master cylinder:
(a) Tear down the four nuts and the three-way joint.
(b) Tear down the master cylinder and sealing washer from
the vacuum booster
cup cap
filtering screen
oil cup
vacuum booster assembly
sealing liner
master cylinder bodyfront three-way valve
SST
SST