oil temperature GREAT WALL SO COOL 2006 Service Manual

TF-65D5D-Oil filling plug
5L-Oil drain plug5L2. Regular lubricant change
(a) The oil level of lubricant in transfer box shall be checked
when exchanging the engine lubricant or after the vehicle
covers 8000 kilometers, and the lubricant shall be added
as requirement.
(b) The lubricant shall be changed with the specified one
every year or after the vehicle covers 48000 kilometers.
3. Lubricant inspection approach
(a) Clean the oil filling plug and the around area.
(b) Open the oil-filling plug to check whether the lubricant
can flows out or not.
(c) if the lubricant can flow out, which means the real
lubricant volume is under the prescribed value, and the
specified lubricant shall be added into the transfer box
until the lubricant can flow from the oil filler hole.
(d) Propel the oil-filling plug tightly according to the given
Tightening moment.
Tightening moment
(19
30)N
m
Notice: The vehicle shall run for a certain time before
checking or exchanging the lubricant so that the
temperature of lubricant in transfer box may be a little
higher. Do not use hammer or other punching tools to
open or propel the oil drain plug or oil filling plug, otherwise,
the thread hole on the frame will be damaged
4. Lubricant change
(a) Clean the oil filling plug and oil drain plug and the around
area.
(b) Put down a oil container under the transfer box.
(c) Open the oil drain plug.
(d) Open the oil-filling plug.
(e) Drain the lubricant up.
(f) Mount the oil drain plug and screw it up according to the
given Tightening moment.
Tightening moment
(19
30)N
m
(g) Add the lubricant through the oil filler hole until the
lubricant overflows. Mount the oil-filling plug and tighten
it according to the Tightening moment.
Tightening moment : (19
30)N
m Transfer Box
lubricant grade: ATF--3Product Description and Simple Maintenance

SR-13Steering System
Power Steering (On-Vehicle Inspection)
tensioning wheelpower steering oil
pump
crankshaftOn-vehicle inspection
Inspection on tension of driver conveyor
Measure the tension of drive conveyor.
Drive conveyor tension: under the condition of 98 N.
New conveyor: (5-7)mm
Old conveyor:
(7-9)mm
Remark:
ìnew conveyorî means the conveyor that is used on the
machine less than five minutes;
ìold conveyorî means the conveyor that is used on machine
more than five minutes
Check for height of liquid level
1. Keep the body in horizontal status
2. Increase the liquid temperature
When the engine runs idly by 1000 r/m or less, rotate the
steering wheel several times from the locking position to the
reverse locking position to increase the liquid temperature.
3. Check to see whether there is foam or emulsification;
Remark: the foam or emulsification shows there is air in the
system or the liquid level is over-low.
4. Check the liquid level height in oil cup;
Check the liquid level height and, if needed, add the oil.

SR-15Steering System
Power Steering (On-Vehicle Inspection)
6. Exhaust the air in steering system:
(a) Loosen the bleeding plug;
(b) Screw up the bleeding plug when there is no air bubble
exhausted from the pipeline.
Notice: take care not let the ethane pipe slide from the
bleeding plug, because the liquid is high in temperature
and pressure.
7. Check to see whether there is air bubble or turbidities
in the oil cup, and ensure the liquid level will not
exceed the max value when the engine stops,
Measure the liquid height under the condition of engine running,
then turn off the engine and measure the liquid height again.
In case any problem is found, repeat the approaches of (5) and
(6) in Power Steering Liquid Change. If the problem still
exists, repair the power steering oil pump.
RPM RPM

BE-34Body Electric System
Combination Instrument
Electric circuit diagram (continued)
A16 A1 B16 B1
SL SK
B1
B16
A1
A16
speed and mileage meter
4P
G
VA9vehicle speed signal
A11odometer sensorA10odometer sensor anode
B11sensor signalelectronic tachometer
water thermometer
fuel gaugecoolant temperature sensor
B5
A12
fuel gauge sensor
B14
A2
B3
upper beam
_NPdifferential latch-in
safety belt
preheating
sediment water alarmingelectricity charging/
discharging
fuel level alarming
brake failure alarming lamp
oil pressure alarming lamp
rear fog lamp
engine failure
four wheel drive indicating lamp
A1 Aturn indicating lamp
B16 left turn indicating lamp
A8
B4 +B7 - B8 A16 B15 B2B1 A15 A14B6 A13 B10B9
SY SJaccumulator plus four door-closing indicating lampA3turn on when the door is opened.
A11odometer sensor_NO
electronic odometer
electronic tachometerA10
B11
engine ignition coil
water thermometer
fuel gauge
B5
A12
neutral gear indicating lampA9
_NP
upper beamB14
differential latch-in
vacuum alarming
preheating
sediment water alarming
electricity charging/
discharging
fuel level alarming
brake failure alarming lamp
oil pressure alarming lamp
rear fog lamp
engine failure
four wheel drive indicating lamp
A1 left turn indicating lamp
B16 right turn indicating lamp
A8
B4 +
instrument lighting
system
B8
B7 - A16 B15 B2
B1 A15A14 B6 A13 B9 B3 B10A2
instrument lighting
system

BE-68Body Electric System
Wire Harness Distribution
Housing wire harness
1 back-up lamp switch
2 starter
3 starter
4 oil pressure sensor
5 grounding wire
6 grounding wire
7 connected to protective box II
8 protective box II
9 connected to protective box II
10 starter11 air-conditioner compressor12water temperature sensor
13 washer motor
14 right headlamp
15 right lever-shaped lamp
16 electric horn
17 generator
18 left headlamp
19 left lever-shaped lamp
20 front turn lamp of left side
21 connected to protective box I
1
2
P
4 5 6 7
8
V
1011
12
13
14
NR1617
18
192021
Wire harness distribution
aê

AC-3Air Conditioning System
Introduction
(c) Tighten the O-ring matching position or the threaded position
to the specified moment.
4. Take notice when connecting measuring meter at branch pipes:
(a) Connect the end of filling hose with high speed joint to the
filling valve of compressor.
(b) Letter
D
marked on the compressor near the auxiliary valve
represents the side of high voltage while
S
means the side of
low voltage, which shall be looked out when connecting the hose.
(c) Fasten the bolts by hand, and
(d) In order to prevent the hose from loosing, lubricant oil shall not
be spread at the connection position.
Remarks: after connecting the measuring meter on branch pipes to
the refrigerant container (repairing tank), the air in the hose shall be
exhausted up.
5. Take notice when vacuumizing:
After vacuumizing for 20 min, maintain the container at certain
pressure to ensure that all air in it is exhausted up, and another
inspection shall be made to see whether there is leakage.
6. Take notice when handling with the refrigerant container
(repairing tank):
(a) Do not heat it.
(b) Store the container at the place where temperature is under 40

(c) In case of heating the repairing tank with hot water, care shall
be paid to the valves at the top of tank, do not dip them into the
water, or the water will penetrate into the cooling system.
(d) The empty repairing tank is forbidden to reuse.
8. Take notice when using the high-pressure air cylinder type
inspecting device:
(a) In case the open fire is used, it is the first to ensure before using
there is no flammable material around.
(b) Be careful because toxic gas will be produced when the
gaseous refrigerant meets with the open fire. 7. Take notice in the A/C operation or when adding the liquid
refrigerant:
(a) In case the gaseous refrigerant in the cooling system is
insufficient, which can lead to the compressor burns out, and
such accidents shall be avoided.
(b) If the valve on the side of high pressure is uncovered, the
refrigerant will flow in the reverse direction, which may lead
to the break of the repairing tank, therefore, only valves on the
side of low pressure are allowed to open or closed.
(c) If the repair tank is laid in reverse direction, and the refrigerant
is added in liquid status, the liquid refrigerant will be
compressed, which may lead to failure of the compressor,
therefore, refrigerant shall be inflated in the gaseous status.
(d) Be careful not over-inflate the gaseous refrigerant, otherwise,
such failures as insufficient cooling, increase of oil consuming
or over heat of engine will be followed.
under 40

incorrect
correct
measuring meter of branch pipe
loose over-fastened
A/C operation

B0-20Vehicle Body
Adhesive Strip On Body Collision Avoidance
Adhesive strip of body collision avoidance
Notices on storing the adhesive strip of body collision avoidance:
1. The adhesive strip should be stored in the cool shadow place where can avoid the direct lighting of sun,
the high temperature and the dust.
2. As the adhesive strip is the PVC product, do not make it touch the paint thinner, other solvents and the
boiling water.
3. The limit storage period of adhesive strip is 9 months.
Element figure
exterior adhesive
strip at front doorexterior adhesive
strip at rear column
exterior adhesive
strip on wing panelexterior adhesive
strip at tailgateexterior adhesive
strip at rear body