width GREAT WALL SO COOL 2006 Service Manual

CL-9Clutch
Clutch cluster
b) Mount the guide bearing with SST.
Remark: the bearing shall be verified in good running after it
is encased in the flywheel hub.
2. Check whether there is abrasion on the diaphragm spring.
Check the abrasion depth and width of diaphragm spring with
calipers.
Limit value: Max depth: 0.6mm
Max width: 5mm
If the abrasion depth or width of the diaphragm spring exceeds
the limit value, change the diaphragm spring .
3. Check the separation bearing
Exert force in radial direction by hand to rotate the bearing.
If it cannot be rotated or if the resistance is too large, change
the separation bearing.
Remark:
Remark: as this bearing is lubricated permanently, it doesnít
need to be cleaned or lubricated.
Mount of clutch cluster
1. Mount the clutch rib on flywheel;
Mount the clutch rib on flywheel with SST.
2. Mount the clutch pressure plate
a) Align the marks on clutch pressure plate and that on flywheel;
b) Screw up the bolts in even manner around the clutch pressure
plate until pressure plate and the flywheel contact closely,
then tighten the bolts.
Tightening moment: 30 N
m
Remark: tighten the uppermost bolt of the three that is near to
the locating pin.
SST
flywheel sideSST
alignment
mark

PR-10Drive Shaft
Drive Shaft
5. Snapping ring mount
(a) Mount two snapping rings with the same thickness.
Remarks: Do not use the used snapping ring.
(b) Tap the universal joint yoke lightly with a hammer until
there is no clearance between the outer bearing race and
the snapping ring.
6. Cross shaft bearing inspection
Check the cross shaft bearing to see whether it can run freely
Remarks: the approach for mounting the cross shaft bearing at
the bearing end is the same.
(c) Encase the new cross shaft in the universal joint yoke.
(d) Mount the new bearing on the cross shaft with SST tool,
andSST
(e) Adjust the two bearings with SST tool so that the widths
of two snapping ring grooves are equal and maximum.

A-2
Clutch
Specification
Item Specification
Fastening torque for clutch tube on master cylinder
Fastening torque for clutch tube on wheel-brake cylinder
Fastening torque for clutch pressure plate160
190-200
5-15
0.3
0.8
0.2
0.6
5
Max misplacement
0.5 Pedal height (calculated from front wall
Pedal free stroke
Min depth of clutch-facing rivet
Max radial swing difference of clutch rib
Max radial swing difference of flywheel
Max width of wear of diaphragm spring
Max width of wear of diaphragm spring
Alignment degree of diaphragm spring endApplicable vehicle model
Dr SF
SL SK SY SJ
Dr SF SL SK SY SJ
Dr SF SL SK SY SJ
Dr SF SL SK SY SJ
Dr SF SL SK SY SJ
Dr SF SL SK SY SJ
Dr SF SL SK SY SJ
Dr SF SL SK SY SJ
Torsion moment
Fastening location (N*m)
15-17
15-17
30 Applicable Vehicle model
Dr SF SL SK SY SJ
Dr SF SL SK SY SJ
Dr SF SL SK SY SJ
Gearbox
Three-grade maintenance for gearbox
1. Grade I maintenance for gear box
Grade I maintenance: Check the lubricant level to see whether the lubricant level is in alignment with the lower edge of oil
filler; if the lubricant is lower than the oil filler lower edge, add the lubricant; or the insufficient lubricant will lead to the poor
lubrication or burn-out of bearing and teeth; while the over-high lubricant will cause the overheating and oil leakage.
2. Grade II maintenance for gear box
Grade II maintenance: The gear box of a new vehicle should be maintained by exchanging the lubricant during the
first grade II maintenance and should be washed with kerosene; and the lubricant quality should be checked in the
grade II maintenance in later time, if the lubricant is diluted, gumming or over-dirty, it should be changed.
3. Grade III maintenance
The gearbox should be disassembled for inspection, washing and oil change.
Notice: As the new vehicle is in the running-in status, the gearbox should be maintained by exchanging lubricant
after the vehicle covers 1500 km,
Lubricant Type
GL-5 SAE80W/90
Torsion moment of relative connecting elements
Tung Teeth: Tang tooth(5DYA4TWD
5DYA8FWD)
Unit
ãã Specification of Maintenance and Up-Keeping
Clutch and Gearbox
Locating screw of fork axle at first and second gear
Locating screw of yoke block
Screw on baffle of rear bearing of output shaft
Screw of reverse idler shaft
Bolt of gearshift cover
Bolt of front cover
Bolt of rear body
Bolt of clutch shell
Bolt of locating spring13
17
15
20
17
22
17
20
15
20
15
20
30
45
30
45
17
22 Fastening location N*m