maintenance HONDA ACCORD 2003 CL7 / 7.G Service Manual
[x] Cancel search | Manufacturer: HONDA, Model Year: 2003, Model line: ACCORD, Model: HONDA ACCORD 2003 CL7 / 7.GPages: 380, PDF Size: 10.81 MB
Page 292 of 380
Run the air conditioning at least once
a week during the cold weather
months. Run it f or at least ten
minutes while you are driving at a
steady speed with the engine at
normal operating temperature. This
circulates the lubricating oil con-
tained in the ref rigerant.If the air conditioning does not get as
cold as before, have your dealer
check the system. Recharge the
system with Ref rigerant HFC-134a
(R-134a). (See Specif ications on page
.)
Your car’s air conditioning is a sealed
system. Any major maintenance,
such as recharging, should be done
by a qualif ied mechanic. You can do
a couple of things to make sure the
air conditioning works ef f iciently.
Periodically check the engine’s
radiator and air conditioning
condenser f or leaves, insects, and
dirt stuck to the f ront surf ace. These
block the air f low and reduce cooling
ef f iciency. Use a light spray f rom a
hose or a sof t brush to remove them. 364
Optional f or U.S. DX models
A ir Condit ioning Syst em
Maint enance299
AIR CONDITIONING CONDENSER
Whenever you have the air conditioning
system serviced, make sure the service
f acility uses a ref rigerant recycling
system. This system captures the
ref rigerant f or reuse. Releasing
ref rigerant into the atmosphere can
damage the environment.
The condenser and radiator f ins bend
easily. Only use a low-pressure spray
or sof t-bristle brush to clean them.
— —y
y
( y y
Page 295 of 380
µµ
An auto-tensioner adjusts the tension
of the drive belt. The pointer on the
auto-tensioner should be in the
proper range. It should be checked
accordingtothetimeanddistance
recommendations in the
maintenance schedule. Take your car to a Honda dealer to
replacethedrivebelt.
If the pointer is out of this range or
you see signs of wear, have the drive
belt replaced by your Honda dealer
as soon as possible.
Check the condition of the drive belt.
Examine the edges of the belt f or
cracks or fraying. In very high temperatures
(over 110°F, 43°C).
In very low temperatures
(under 20°F, 29°C).
Replace these belts at 60,000 miles
(U.S.) or 100,000 km (Canada) if you
regularly drive your car in one or
more of these conditions:
The timing belt and balancer belt
should normally be replaced at the
intervals shown in the maintenance
schedule.
6-cylinder models
6-cylinder models only
Timing Belt
Drive Belt
Maint enance
Drive Belt, Timing Belt
302
4-cylinder models
— —yy
( y y
Page 296 of 380
Use a gauge to measure the air
pressure at least once a month. Even
tires that are in good condition may
lose one to two psi (10 to 20 kPa, 0.1
to 0.2 kgf /cm ) per month.
Remember to check the spare tire at
thesametimeyoucheckallthe
other tires.
Check the pressure in the tires when
they are cold. This means the car
has been parked f or at least three
hours. If you have to drive the car
bef ore checking the tire pressure,
the tires can still be considered
‘‘cold’’ if you drive less than 1 mile
(1.6 km).
Keeping the tires properly inf lated
provides the best combination of
handling, tread lif e, and riding
comf ort. Underinf lated tires wear
unevenly, adversely af f ect handling
and f uel economy, and are more
likely to f ail f rom being overheated.
Overinf lated tires can make your car
ride more harshly, are more prone to
damage f rom road hazards, and wear
unevenly.
We recommend that you visually
check your tires every day. If you
think a tire might be low, check it
immediately with a tire gauge.
To saf ely operate your car, your tires
must be the proper type and size, in
good condition with adequate tread,
and correctly inf lated. The f ollowing
pages give more detailed inf ormation
on how and when to check air
pressure, how to inspect your tires
for damage and wear, and what to do
when your tires need to be replaced.
CONT INUED
Inf lation
Tires
Maint enance303
Using tires that are excessively
worn or improperly inflated can
cause a crash in which you can
be seriously hurt or killed.
Follow all instructions in this
owner’s manual regarding tire
inflation and maintenance.
— —yy
( y y
Page 298 of 380
Every time you check inf lation, you
should also examine the tires f or
damage, f oreign objects, and wear.
Youshouldlookfor:Bumps or bulges in the tread or
side of the tire. Replace the tire if
youfindeitherof theseconditions.
Cuts, splits, or cracks in the side
of the tire. Replace the tire if you
can see f abric or cord.
Excessive tread wear. In addition to proper inf lation,
correct wheel alignment helps to
decrease tire wear. If you f ind a tire
is worn unevenly, have your dealer
check the wheel alignment.
The tires were properly balanced by
the factory. They may need to be
rebalanced at some time bef ore they
are worn out. Have your dealer
check the tires if you f eel a consis-
tent vibration while driving. A tire
should always be rebalanced if it is
removed f rom the wheel f or repair.
Your car’s tires have wear indicators
molded into the tread. When the
tread wears down to that point, you
will see a 1/2 inch (12.7 mm) wide
band running across the tread. This
shows there is less than 1/16 inch
(1.6 mm) of tread lef t on the tire. A
tire that is this worn gives very little
traction on wet roads. You should
replace the tire if you can see the
tread wear indicator in three or more
places around the tire.
CONT INUED
Inspection
Maintenance
Tires
Maint enance305
INDICATOR LOCATION MARKS
TREAD WEAR INDICATORS
— —yy
( y y
Page 316 of 380
Block the rear wheels.
Fill the f uel tank.
Wash and dry the exterior
completely.
Cleantheinterior.Makesurethe
carpeting, floor mats, etc. are
completely dry.
Leave the parking brake off. Put
the transmission in Reverse
(5-speed manual) or Park
(automatic).
If you need to park your car f or an
extended period (more than one
month), there are several things you
should do to prepare it f or storage.
Proper preparation helps prevent
deterioration and makes it easier to
get your car back on the road. If
possible, store your car indoors.
If the car is to be stored for a
longer period, it should be
supported on jackstands so the
tires are of f the ground.
Leave one window open slightly (if
the car is being stored indoors).
Disconnect the battery.
Support the f ront wiper blade
arms with a f olded towel or rag so
they do not touch the windshield.
To minimize sticking, apply a
silicone spray lubricant to all door
and trunk seals. Also, apply a car
body wax to the painted surf aces
that mate with the door and trunk
seals.
Change the engine oil and f ilter
(see page ).
If you store your car f or 1 year or
longer, have your Honda dealer
perf orm the inspections as soon as
youtakeitoutof storage(seepages
, ). The 6-cylinder model
needs the inspections called f or in
the 2 years/30,000 miles (48,000 km)
maintenance schedule (Normal
Conditions) and the 4-cylinder model
needs the inspections called f or in
the 2 years/40,000 miles (64,000 km)
maintenance schedule (Normal
Conditions). The replacements
called f or in the maintenance
schedule are not needed unless the
car has actually reached that time or
mileage.
Coverthecarwitha‘‘breathable’’
cover, one made f rom a porous
material such as cotton. Nonporous materials, such as
plastic sheeting, trap moisture,
which can damage the paint.
If possible, run the engine f or a
while periodically (pref erably once
amonth).
270 250 255
St oring Your Car
Maint enance323
— —y
y
( y y
Page 323 of 380
Repair chips and scratches in the
paint as soon as you discover them.
Inspect and clean out the drain
holes in the bottom of the doors
and body.
Check the f loor coverings f or
dampness. Carpeting and f loor
mats may remain damp f or a long
time, especially in winter. This
dampness can eventually cause
the f loor panels to corrode.
Two f actors normally contribute to
causing corrosion in your car:
Moisture trapped in body cavities.
Dirtandroadsaltthatcollectsin
hollows on the underside of the
car stays damp, promoting
corrosion in that area.
Removal of paint and protective
coatings f rom the exterior and
underside of the car. Many corrosion-preventive measures
are built into your Honda. You can
help keep your car f rom corroding
by perf orming some simple periodic
maintenance:
Have the corrosion-preventive
coatings on the underside of your
car inspected and repaired
periodically.
Use a high-pressure spray to clean
the underside of your car. This is
especially important in areas that
useroadsaltinwinter.Itisalsoa
good idea in humid climates and
areas subject to salt air. Be careful
not to damage the ABS wheel
sensors and wiring at each wheel.
1. 2.
Appearance Care
Corrosion Prot ect ion
331
— —yy
( y y
Page 355 of 380
µ
µ µµ µ µµµµµµµµµµµ µ µ
ÎÎ Î
Î
Î
Î
ÎÎ
CONT INUED
Specif ications
T echnical Inf ormation365
Fuses
Battery
Lights
Alignment
Engine
3.43 x 3.9 in (87.0 x 99.0 mm)143.6 cu-in (2,354 cm
)
12 V 60 W (HB3)
12 V 51 W (HB4)
12 V 24/2.2 CP
9.7 : 1
3.39 x 3.39 in (86.0 x 86.0 mm)
182.8 cu-in (2,997 cm)
10 : 1
12 V
12 V
12 V
12 V
12 V
12 V
12 V 21 W
21/5 W
3CP
21 W
21 W
3CP8W
Interior
Under-hood 52 AH/5 HR
38 AH/5 HR
12 V
12 V
Capacity 12 V
12 V
12 V
1.1 W
2CP
5W
8W8W
12 V
12 V
Headlights
Front turn signal/
Front parking lights
Rear turn signal lights
Stop/Taillights
Taillights
High-mount brake light
Back-up lights
License plate light
Ceiling light
Spotlights
Spotlights/Front ceiling lights
Trunk light
Door courtesy light
Vanity mirror lights
Toe-in
Camber Caster
Type
BorexStroke
Displacement
Compression ratio
Spark plugs
0.00 in (0.0 mm)
0.08 in (2.0 mm)0°1°
3°15’
See page 357 or the fuse label
attached to the inside of the fuse
box door on each side of the
dashboard.
See page 356 or the fuse box
cover. See spark plug maintenance sec-
tion pages 291 and 293 .
Water cooled 4-stroke, DOHC
i-VTEC 4-cylinder, SOHC VTEC
6-cylinder (V6), gasoline engine
FrontRear
FrontRear
Front
HighLow
4-cylinder
6-cylinder
1: LX
2: EX (Amber)
3 : 6-cylinder models33
3
12
— —y
y
( y y
Page 361 of 380
Î
ÎThe burning of gasoline in your car’s
engine produces several byproducts.
Some of these are carbon monoxide
(CO), oxides of nitrogen (NOx) and
hydrocarbons (HC). Gasoline
evaporating from the tank also
produces hydrocarbons. Controlling
the production of NOx, CO, and HC
is important to the environment.
Under certain conditions of sunlight
and climate, NOx and HC react to
f orm photochemical ‘‘smog.’’ Carbon
monoxide does not contribute to
smog creation, but it is a poisonous
gas. The United States Clean Air Act
sets standards f or automobile
emissions. It also requires that
automobile manufacturers explain to
owners how their emissions controls
workandwhattodotomaintain
them. This section summarizes how
the emissions controls work.
Scheduled maintenance is on page
.
In Canada, Honda vehicles comply
with the Canadian emission
requirements, as specif ied in an
agreement with Environment
Canada, at the time they are
manuf actured.
Your car has a Positive Crankcase
Ventilation System. This keeps
gasses that build up in the engine’s
crankcase from going into the
atmosphere. The Positive Crankcase Ventilation valve routes them from
the crankcase back to the intake
manif old. They are then drawn into
the engine and burned.
The Onboard Ref ueling Vapor
Recovery (ORVR) system captures
the f uel vapors during ref ueling. The
vapors are adsorbed in a canister
f illed with activated carbon. While
driving, the f uel vapors are drawn
into the engine and burned of f .
As gasoline evaporates in the f uel
tank, an evaporative emissions
control canister f illed with charcoal
adsorbs the vapor. It is stored in this
canister while the engine is of f . Af ter
the engine is started and warmed up,
the vapor is drawn into the engine
and burned during driving.
250
The Clean Air Act
Crankcase Emissions Control
System
Onboard Ref ueling Vapor
Recovery
Evaporative Emissions Control
System
T echnical Inf ormation
Emissions Cont rols
371
— —y y
( y y
Page 371 of 380
µµ
µ
( % ) $
%."#)
This manual describes the procedures involved in the
replacement of damaged body parts.
This manual covers maintenance and recommended
procedures f or repair to engine and chassis components.
It is written f or the Journeyman mechanic, but is simple
enough f or most mechanically-inclined owners to under-
stand.
This manual complements the Service Manual by
providing in-depth troubleshooting inf ormation f or each
electrical circuit in your car.
Authorized Manuals
Service Manual:
Electrical T roubleshooting Manual:
Body Repair Manual:
382 NOTE: Dealers and Companies please provide dealer or company name,
and also the name of the person to whose attention the shipment should
be sent. For purchases outside U.S.A. please write to the address shown
below for a quotation.
P.O. BOX 07280·DETROIT, MICHIGAN 48207·1-800-782-4356
Customer Name Attention
Apartment Number
State & Zip Code
City
Daytime Telephone Number
Check or money order enclosed payable to Helm Inc U.S. funds only.
Do not send cash
Master
Card VISA Check here if your billing address is different
from the shipping address shown above.
Account Number Expiration: Mo. Yr.
CUSTOMER SIGNATURE DATE
Street Address No P.O. Box Number
()
These Publications cannot be returned for credit without receiving advance authorization within 14
days of delivery. On returns, a restocking fee may be applied against the original order.
— —y
y
( y y
Page 372 of 380
CONT INUED
Battery......
Charging System Light . 58, 348
............................
Jump Starting . 342
..............................
Maintenance . 294
............................
Specif ications . 365
..............................
Bef ore Driving . 203
..........................................
Belts, Seat . 8
.........................
Beverage Holders . 104
...................................
Body Repair . 332
Brakes
...........
Anti-lock System (ABS) . 230
.............
Break-in, New Linings . 204
....................
Bulb Replacement . 317
...........................................
Fluid . 284
.......................................
Parking . 102 .........................
System Indicator . 58
........................
Wear Indicators . 229
.............................
Braking System . 229
........................
Break-in, New Car . 204
..
Brightness Control, Instruments . 69
........................
Brights, Headlights . 68
Bulb Replacement
..........................
Back-up Lights . 318
..............................
Brake Lights . 317
..............................
Ceiling Light . 320
................
Door Courtesy Light . 321
................
Front Parking Lights . 315
.................................
Headlights . 312
.........
High-mount Brake Light . 319
...................
License Plate Light . 319
............................
Specif ications . 365
...................................
Spotlights . 321
...............................
Trunk Light . 322
....................
Turn Signal Lights . 315
................
Vanity Mirror Lights . 321
..............................
Bulbs, Halogen . 312
...
Accessories and Modif ications . 212
................................
Accessories . 212
.
Additional Safety Precautions . 213
............................
Modif ications . 213
ACCESSORY (Ignition Key .......................................
Position) . 78
.............
Accessory Power Socket . 107
....................
Additives, Engine Oil . 270
.....................................
Airbag (SRS) . 9
.....................
Air Cleaner Element . 286
............................
Air Conditioning . 112
..............................
Maintenance . 299
.........................................
Usage . 112
.......................
Air Pressure, Tires . 304
.......................
Alcohol in Gasoline . 369
......................................
Antif reeze . 273
Anti-lock Brakes (ABS)
................................
Description . 230
...............................
Indicator . 57, 231
...................................
Operation . 230
.
Anti-thef t Steering Column Lock . 77
..........................
Appearance Care . 325
..........................................
Armrest . 103
................
Audio System . 134, 150, 169 .............
Automatic Speed Control . 195
..............
Automatic Transmission . 222
..........................
Capacity, Fluid . 364
.......
Checking Fluid Level . 280, 281
.......................................
Shif ting . 223
.
Shif t Lever Position Indicator . 223
................
Shif t Lever Positions . 223
....................
Shif t Lock Release . 226
Index
A
B
I
— —y y
( y y