ECO mode HONDA ACCORD 2005 CL7 / 7.G Service Manual

The f luid level should be up to the
edge of the bolt hole. If it is not, add
Honda Manual Transmission Fluid
(MTF) until it starts to run out of the
hole. Reinstall the f iller bolt, and
tighten it securely.
If Honda MTF is not available, you
may use an SAE 10W-30 or 10W-40
viscosity motor oil with the API
Certif ication seal that says ‘‘FOR
GASOLINE ENGINES’’ as a
temporary replacement. However,
motor oil does not contain the proper
additives, and continued use can
cause stiffer shifting. Replace as
soon as it is convenient.
The transmission should be drained
and ref illed with new f luid according
to the time and distance recommen-
dations in the maintenance schedule.
If you are not sure how to check and
add f luid, contact your dealer.Check the f luid level with the
transmission at normal operating
temperature and the vehicle sitting
on level ground.
Remove the check bolt and look for
transmission f luid coming out of the
bolt hole. If a small amount of f luid
drips out of the bolt hole, reinstall
the check bolt.
If no f luid comes out, remove the
f iller bolt. Slowly add Honda Manual
Transmission Fluid (MTF) until it
starts to run out of the check bolt
hole. Let the f luid run out until it
stops, then reinstall the check bolt
and the f iller bolt.
On EX-V6 model
T ransmission Fluid
Manual Transmission
224
CHECK BOLT
WASHER
DRAIN BOLT FILLER BOLT
WASHER
——y


y
(%yy

Always use Honda Heavy Duty
Brake Fluid DOT 3. If it is not
available, you should use only DOT 3
or DOT 4 f luid, f rom a sealed
container, as a temporary
replacement.
Using any non-Honda brake f luid can
cause corrosion and decrease the lif e
of the system. Have the brake
system f lushed and ref illed with
Honda Heavy Duty Brake Fluid
DOT 3 as soon as possible.
Brake f luid marked DOT 5 is not
compatible with your vehicle’s
braking system and can cause
extensive damage.
Check the f luid level in the
reservoirs monthly. There are up to
two reservoirs, depending on the
model. They are:
If Honda MTF is not available, you
may use an SAE 10W-30 or 10W-40
viscosity motor oil with the API
Certif ication seal that says ‘‘FOR
GASOLINE ENGINES’’ as a
temporary replacement. However,
motor oil does not contain the proper
additives, and continued use can
cause stiffer shifting. Replace as
soon as it is convenient.
The transmission should be drained
and ref illed with new f luid according
to the time and distance recommen-
dations in the maintenance schedule.
If you are not sure how to check and
add f luid, contact your dealer.
Pour the f luid into the f iller hole
slowly and caref ully so you do not
spill. Clean up any spill immediately;
it could damage components in the
engine compartment.
Replace the brake f luid according to
the time recommendation in the
maintenance schedule.Brake f luid reservoir (all models)
Clutch f luid reservoir
(manual transmission only)
Transmission Fluid, Brake and Clutch Fluid
Brake and Clutch Fluid
Maint enance
225
——y



y
(%yy

Î Î
ÎÎÎ ÎYoushoulduseyourowntire
pressure gauge whenever you check
your tire pressures. This will make it
easier f or you to tell if a pressure
loss is due to a tire problem and not
due to a variation between gauges.
While tubeless tires have some
ability to self -seal if they are
punctured, you should look closely
for punctures if a tire starts losing
pressure. For convenience, the recommended
cold air pressures and tire sizes are
on a label on the driver’s doorjamb.
For additional inf ormation about
your tires, see page .
The following chart shows the
recommended cold tire pressures f or
most normal and high-speed driving
conditions.
If you check air pressure when the
tires are hot [driven f or several miles
(kilometers)], you will see readings 4
to6psi(30to40kPa,0.3to0.4
kgf /cm ) higher than the cold
readings.Thisisnormal.Donotlet
air out to match the recommended
cold air pressure. The tire will be
underinf lated.
280
Cold Tire Pressure
Tire Size/Type
Compact Spare
Tire Size/Type
Compact Spare Cold Tire Pressure
Front:
Rear: Front:
Rear:
EX-V6 with M/T
EX, LX-V6 and EX-V6 with A/T
1 2
4-cylinder LX model
All models except 4-cylinder LX
Tires
Recommended Tire Pressures
Maint enance
239
P205/65R15 92H 30 psi (210 kPa ,
2.1 kgf/cm)
29 psi (200 kPa , 2.0 kgf/cm
)
P205/60R16 91V
P215/50R17 93V 32 psi (220 kPa ,
2.2 kgf/cm
)
30 psi (210 kPa , 2.1 kgf/cm
)
29 psi (200 kPa ,
2.0 kgf/cm
)
60 psi (420 kPa , 4.2 kgf/cm
) 60 psi (420 kPa ,
4.2 kgf/cm
)
1 2 1 2
——y


y
(%yy

To help increase tire lif e and
distribute wear more evenly, rotate
the tires every 10,000 miles
(16,000 km) on 4-cylinder models
and 7,500 miles (12,000 km) on
6-cylinder models. Move the tires to
the positions shown in the chart each
time they are rotated. If you
purchase directional tires, rotate
only f ront-to-back.It is best to replace all f our tires at
thesametime.If thatisnotpossible
or necessary, replace the two f ront
tires or two rear tires as a pair.
Replacing just one tire can seriously
af f ect your vehicle’s handling.
Replace your tires with radial tires of
the same size, load range, speed
rating, and maximum cold tire
pressure rating (as shown on the
tire’s sidewall).
Mixing radial and bias-ply tires on
your vehicle can reduce braking
ability, traction, and steering
accuracy. Using tires of a dif f erent
size or construction can cause the
ABS to work inconsistently.
TheABSworksbycomparingthe
speed of the wheels. When replacing
tires, use the same size originally
supplied with the vehicle. Tire size
and construction can affect wheel
speed and may cause the system to
work. If you ever replace a wheel, make
sure that the wheel’s specif ications
match those of the original wheels.
Replacement wheels are available at
your dealer.
T ire Rotation Replacing T ires and Wheels
Tires
Maint enance
241
(For Non-directional
Tires and Wheels)
Front
(For Directional
Tires and Wheels)Front
Installing improper tires on your
vehicle can affect handling and
stability. This can cause a crash
in which you can be seriously
hurt or killed.
Always use the size and type of
tires recommended in this
owner’s manual.
——y


y
(%yy

´If you mount snow tires on your
vehicle, make sure they are radial
tires of the same size and load range
as original tires. Mount snow tires on
all f our wheels. The traction
provided by snow tires on dry roads
maybelowerthanyouroriginaltires.
Check with the tire dealer f or
maximum speed recommendations.
Tires marked ‘‘M S’’ or ‘‘All
Season’’ on the sidewall have an all-
weather tread design suitable for
most winter driving conditions.
For the best perf ormance in snowy
or icy conditions, you should install
snow tires or tire chains. They may
be required by local laws under
certain conditions.
Wheels:
Tires:
See page f or inf ormation about
DOT Tire Quality Grading, and page
f or tire size and labeling
inf ormation. 278
280
LX model
LX model
EX, LX-V6 and EX-V6 with A/T models
EX-V6 with M/T model
EX, LX-V6 and EX-V6 with A/T modelsEX-V6 with M/T model
Tires
Snow T iresWinter Driving
Wheel and T ire Specif ications
242
15x61/2JJ
16x61/2JJ
17x7JJ
P205/65R15 92H
P215/50R17 93V
P205/60R16 91V
——y



y
(%yy

µ
´
´
Start the vehicle. If the starter
motor still operates slowly, check
that the jumper cables have good
metal-to-metal contact.
If the booster battery is in another
vehicle, have an assistant start
that vehicle and run it at a fast idle.
Connect the second jumper cable
to the negative ( ) terminal on
the booster battery. Connect the
other end to the grounding strap
as shown. Do not connect this
jumper cable to any other part of
the engine.
Connect one jumper cable to the
positive ( ) terminal on your
battery. Connect the other end to
the positive ( ) terminal on the
booster battery.
6.
5.
4.
3.
CONT INUED
Jump Starting
T aking Care of t he Unexpect ed
257
6-cylinder models
4-cylinder models
6-cylinder models BOOSTER
BATTERY
——y



y
(%yy