engine HONDA ACCORD 2005 CL7 / 7.G Manual PDF

This indicator may also come on
along with the ‘‘D’’ indicator.
Your vehicle has certain ‘‘readiness
codes’’ that are part of the on-board
diagnostics f or the emissions
systems. In some states, part of the
emissions testing is to make sure
these codes are set. If they are not
set, the test cannot be completed.
If your vehicle battery has been
disconnected or gone dead, these
codes are erased. It takes at least
three days of driving under various
conditions to set the codes again.
If the indicator comes on
while driving, it means one
of the engine’s emissions control
systems may have a problem. Even
though you may f eel no dif f erence in
your vehicle’s perf ormance, it can
reduce your f uel economy and cause
increased emissions. Continued
operation may cause serious damage.
If you have recently ref ueled your
vehicle, the indicator coming on
could be due to a loose or missing
f uel f ill cap. Tighten the cap until it
clicks at least three times.
Tightening the cap will not turn the
indicator of f immediately; it takes at
least three days of normal driving.
If the indicator comes on repeatedly,
even though it may turn of f as you
continue driving, have the vehicle
checked by the dealer as soon as
possible. To check if they are set, turn the
ignition switch to ON (II), without
starting the engine. The malf unction
indicator lamp will come on f or 20
seconds. If it then goes of f , the
readiness codes are set. If it blinks 5
times, the readiness codes are not
set. If possible, do not take your
vehicle f or a state emissions test
until the readiness codes are set.
Refer to
f or more inf ormation (see page ).
284
Malf unct ion Indicat or L amp
Readiness Codes State Emissions T esting
T aking Care of t he Unexpect ed
261
If you keep driving with the
malf unction indicator lamp on, you can
damage your vehicle’s emissions
controls and the engine. Those repairs
may not be covered by your vehicle’s
warranties.
——y


y
(%yy

µ
µ
If your vehicle needs to be towed,
call a prof essional towing service or
organization. Never tow your vehicle
with just a rope or chain. It is very
dangerous.
If , due to damage, your vehicle must
be towed with the f ront wheels on
the ground, do the f ollowing:
Release the parking brake.
Shif t the transmission to Neutral. With the f ront wheels on the ground,
it is best to tow the vehicle no farther
than 50 miles (80 km), and keep the
speedbelow35mph(55km/h).
If your vehicle is equipped with a
f ront spoiler, remove it bef ore
towing so it is not damaged.
Turn of f the engine.
ShifttoD,thentoN.
Start the engine.
Release the parking brake.
The tow
truck uses two pivoting arms that go
under the tires (f ront or rear) and lif t
them of f the ground. The other two
tires remain on the ground. The operator
loads your vehicle on the back of a
truck.
Therearetwowaystotowyour
vehicle.
CONT INUED
Manual Transmission:
Automatic Transmission:
Emergency T owing
Wheel-lif t Equipment
Flat -bed Equipment
T his is
an acceptable way to tow your
vehicle. This is the best way to trans-
port your vehicle.
T aking Care of t he Unexpect ed
269
Improper towing preparation will
damage the transmission. Follow the
above procedure exactly. If you cannot
shif t the transmission or start the
engine (automatic transmission), your
vehicle must be transported with the
f ront wheels of f the ground. Trying to lif t or tow your vehicle by the
bumpers will cause serious damage.
The bumpers are not designed to
support the vehicle’s weight.
——y

y
(%yy

Your vehicle has several identif ying
numbers in various places.
The vehicle identif ication number
(VIN) is the 17-digit number your
dealer uses to register your vehicle
f or warranty purposes. It is also
necessary f or licensing and insuring
your vehicle. The easiest place to
find the VIN is on a plate fastened to
the top of the dashboard. You can
seeitbylookingthroughthe
windshield on the driver’s side. It is
also on the certification label
attached to the driver’s doorjamb,
and is stamped on the engine
compartment bulkhead. The VIN is
also provided in bar code on the
certif ication label.
Identif ication Numbers
272
VEHICLE IDENTIFICATION NUMBERCERTIFICATION LABEL
——y


y
(%yy

The transmission number is on a
label on top of the transmission.
The engine number is stamped into
the engine block. It is on the f ront.
Identif ication Numbers
T echnical Inf ormation
273
AUTOMATIC/MANUAL TRANSMISSION NUMBER ENGINE NUMBER
6-cylinder Models MANUAL
TRANSMISSION
NUMBERENGINE NUMBER
4-cylinder Models
AUTOMATIC TRANSMISSION NUMBER
——y



y
(%yy

µµÎ Î
Î Î
Specif ications (4-cylinder Models)
274
Dimensions
Weights
Air Conditioning Capacities
187.6 in (4,766 mm)
71.3 in (1,810 mm)
55.7 in (1,415 mm)
105.1 in (2,670 mm)
61.1 in (1,553 mm)
61.2 in (1,554 mm)
1.88 US gal (7.1
)
1.90 US gal (7.2)
1.37 US gal (5.2
)
1.40 US gal (5.3)
5.6 US qt (5.3
)
HFC-134a (R-134a)
17.6 19.4 oz (500 550 g) 4.4 US qt (4.2
)
4.2 US qt (4.0
)
ND-OIL8 2.0 US qt (1.9
)
2.2 US qt (2.1)
3.0 US qt (2.8)
6.9 US qt (6.5)
2.6 US qt (2.5
)
0.16 US gal (0.6
) 4.8 US qt (4.5
)
17.09 US gal (64.7
)
Including the coolant in the reserve tank and that remaining in the
engine.
Reserve tank capacity:
Excluding the oil remaining in the engine.
Length
Width
Height
Wheelbase
Track
Gross vehicle weight rating See the certification label attached
to the driver’s doorjamb.
Refrigerant type
Charge quantity
Lubricant type Fuel tank
Engine
coolant
Engine oil
Manual trans-
mission fluidAutomatic
transmission
fluid
Windshield
washer
reservoir
FrontRear
Approx.
1: 2: Change
Manual Automatic
Total
ManualAutomatic
Change Including
filter
Without
filter
Total
ChangeTotal
ChangeTotal
U.S. Vehicles
Canada Vehicles1 2
——y



y
(%yy

µ
µ µµ µ µµµµµµµµµ µ µ
ÎÎ
ÎÎÎÎÎÎ
Specif ications (4-cylinder Models)
T echnical Inf ormation
275
Tires
Lights Battery
Fuses Engine
Alignment
12 V
12 V
24/2.2 CP
12 V
12 V
60 W (HB3)
51 W (HB4)
12 V
12 V
12 V
12 V
12 V
12 V
12 V
12 V
12 V
21 W
21/5 W
18 W
3CP8W
21 W5W
2CP
1.1 W8W
12 V
12 V 38 AH/5 HR
47 AH/20 HR 3.43 x 3.90 in (87.0 x 99.0 mm)
144 cu-in (2,354 cm
)
9.7 : 1
0.00 in (0.0 mm)
0.08 in (2.0 mm) 0°
1°
3°15’
P205/65R15 92H P205/60R16 91V
T135/90D15 100M
30 psi (210 kPa , 2.1 kgf/cm
)
32 psi (220 kPa , 2.2 kgf/cm)
29 psi (200 kPa , 2.0 kgf/cm)
30 psi (210 kPa , 2.1 kgf/cm)
60 psi (420 kPa , 4.2 kgf/cm)
Size
Pressure Water cooled 4-stroke i-VTEC
4-cylinder gasoline engine
Headlights
Front turn signal/parking/side
marker lights
Rear turn signal lights
Back-up lights
License plate lights
Ceiling light
High-mount brake light
Trunk light
Door courtesy lights
Vanity mirror lights
Spotlights
Capacity
Interior
Under-hood Type
BorexStroke
Displacement
Compression ratio
Spark plugs
Toe-in
CamberCaster
NGK:
DENSO:
IZFR6K-11SKJ20DR-M11
See page 268 or the fuse label
attached to the inside of the fuse
box lid.
See page 267 or the fuse box
cover. FrontRear
FrontRear
Front
HighLow
1: LX
2: EXFront/Rear
Spare
Front Rear
Spare
Stop/taillight/side marker lights
1 2
1212
——y


y
(%yy

µµÎ Î
Î Î
Specif ications (6-cylinder Models)
276
Dimensions
Weights
Air Conditioning Capacities
61.1 in (1,553 mm)
61.2 in (1,554 mm)
17.6 19.4 oz (500 550 g) HFC-134a (R-134a)
ND-OIL8
2.6 US qt (2.5
)
4.8 US qt (4.5)
7.6 US qt (7.2
)
3.1 US qt (2.9)
5.3 US qt (5.0
)
4.2 US qt (4.0
)
4.5 US qt (4.3
)
0.16 US gal (0.6
) 1.77 US gal (6.7
)
2.22 US gal (8.4
)
105.1 in (2,670 mm)
1.74 US gal (6.6
)
187.6 in (4,766 mm)
71.3 in (1,810 mm)
55.7 in (1,415 mm)
2.17 US gal (8.2
)
2.3 US qt (2.2
)
2.6 US qt (2.5)
17.09 US gal (64.7
)
Including the coolant in the reserve tank and that remaining in the
engine.
Reserve tank capacity:
Excluding the oil remaining in the engine.
Length
Width
Height
Wheelbase
Track
Gross vehicle weight rating
Refrigerant type
Charge quantity
Lubricant type
See the certification label attached
to the driver’s doorjamb. Fuel tank
Engine
coolant
Engine oil Manual
transmission
fluidAutomatic
transmission
fluid
Windshield
washer
reservoir
FrontRear
Approx.
1: 2: Change
Manual Automatic
Total
ManualAutomatic
Change Including
filter
Without
filter
Total
ChangeTotal
Change Total
U.S. Vehicles
Canada Vehicles1 2
——y


y
(%yy

µ
Î Î
µµµ µ µµµµµµµµµ µ µ
ÎÎ
ÎÎ
ÎÎ
Specif ications (6-cylinder Models)
T echnical Inf ormation
277
Lights Battery
Fuses Engine
Alignment
Tires
12 V
12 V
12 V
12 V
12 V
12 V
12 V
12 V
12 V
12 V
12 V
12 V
12 V
12 V
12 V 63 W (HB3)
51 W (HB4)
24/2.2 CP
21 W
21/5 W
18 W
3CP8W
21 W5W
2CP
1.1 W8W
52 AH/5 HR
65 AH/20 HR
3.39 x 3.39 in (86.0 x 86.0 mm)
183 cu-in (2,997 cm
)
10.0 : 1
0.00 in (0.0 mm)
0.08 in (2.0 mm) 0°1°
3°15’
P215/50R17 93V
P205/60R16 91V
T135/90D15 100M
32 psi (220 kPa , 2.2 kgf/cm
)
T135/80R16 101M
60 psi (420 kPa , 4.2 kgf/cm
)
29 psi (200 kPa , 2.0 kgf/cm)
30 psi (210 kPa , 2.1 kgf/cm)
Headlights
Front turn signal/parking/side
marker lights
Rear turn signal lights
Back-up lights
License plate lights
Ceiling light
High-mount brake light
Trunk light
Door courtesy lights
Vanity mirror lights
Spotlights
Capacity
Interior
Under-hood Type
BorexStroke
Displacement
Compression ratio
Spark plugs
Water cooled 4-stroke
SOHC VTEC
6-cylinder gasoline engine
Toe-in
CamberCaster Size
Pressure NGK:
DENSO:
IZFR6K-11SKJ20DR-M11
See page 268 or the fuse label
attached to the inside of the fuse
box lid.
See page 267 or the fuse box
cover. FrontRear
FrontRear
Front
HighLow
1:2:LX-V6, EX-V6 with automatic transmission
EX-V6 with manual transmission Front/Rear
Spare
Front Rear
Spare
Stop/taillight/side marker lights
1 2
12
12
——y

y
(%yy

Î
Î
The United States Clean Air Act
sets standards f or automobile
emissions. It also requires that
automobile manufacturers explain to
owners how their emissions controls
workandwhattodotomaintain
them. This section summarizes how
the emissions controls work.
Scheduled maintenance is on pages
and .
In Canada, Honda vehicles comply
with the Canadian emission
requirements, as specif ied in an
agreement with Environment
Canada, at the time they are
manuf actured.
Your vehicle has a positive
crankcase ventilation system. This
keeps gasses that build up in the
engine’s crankcase f rom going into
the atmosphere. The positive crankcase ventilation valve routes
them from the crankcase back to the
intake manif old. They are then
drawn into the engine and burned.
As gasoline evaporates in the f uel
tank, an evaporative emissions
control canister f illed with charcoal
adsorbs the vapor. It is stored in this
canister while the engine is of f . Af ter
the engine is started and warmed up,
the vapor is drawn into the engine
and burned during driving.
The onboard ref ueling vapor
recovery (ORVR) system captures
the f uel vapors during ref ueling. The
vapors are adsorbed in a canister
f illed with activated carbon. While
driving, the f uel vapors are drawn
into the engine and burned of f .
The burning of gasoline in your
vehicle’s engine produces several by-
products. Some of these are carbon
monoxide (CO), oxides of nitrogen
(NOx), and hydrocarbons (HC).
Gasoline evaporating f rom the tank
also produces hydrocarbons.
Controlling the production of NOx,
CO, and HC is important to the
environment. Under certain
conditions of sunlight and climate,
NOx and HC react to f orm
photochemical ‘‘smog.’’ Carbon
monoxide does not contribute to
smog creation, but it is a poisonous
gas.
201
206
Emissions Cont rols
The Clean Air Act
Crankcase Emissions Control
System Evaporative Emissions Control
System
Onboard Ref ueling Vapor
Recovery
T echnical Inf ormation
281
——y

y
(%yy

The exhaust emissions controls
include f our systems: PGM-FI,
ignition timing control, exhaust gas
recirculation and three way catalytic
converter. These f our systems work
together to control the engine’s
combustion and minimize the
amount of HC, CO, and NOx that
comes out the tailpipe. The exhaust
emissions control systems are
separate f rom the crankcase and
evaporative emissions control
systems.
The PGM-FI system uses sequential
multiport f uel injection. It has three
subsystems: air intake, engine
control, and f uel control. The
powertrain control module (PCM) in
automatic transmission vehicles or
the engine control module (ECM) in
manual transmission vehicles uses
various sensors to determine how
much air is going into the engine. Itthen controls how much f uel to inject
under all operating conditions. The emissions control systems are
designed and certif ied to work to-
gether in reducing emissions to
levels that comply with the Clean Air
Act. To make sure the emissions
remain low, you should use only new
Honda replacement parts or their
equivalent f or repairs. Using lower
qualitypartsmayincreasethe
emissions f rom your vehicle.
The emissions control systems are
covered by warranties separate f rom
the rest of your vehicle. Read your
warranty manual f or more inf orma-
tion.
The three way catalytic converter is
in the exhaust system. Through
chemical reactions, it converts HC,
CO, and NOx in the engine’s exhaust
to carbon dioxide (CO ), nitrogen
(N ), and water vapor.
The exhaust gas recirculation (EGR)
system takes some of the exhaust
gas and routes it back into the intake
manif old. Adding exhaust gas to the
air/f uel mixture reduces the amount
of NOx produced when the f uel is
burned.
This system constantly adjusts the
ignition timing, reducing the amount
of HC, CO, and NOx produced.
2
2
Emissions Cont rols
Exhaust Emissions Controls Replacement Parts
PGM-FI Syst emExhaust Gas Recirculat ion (EGR)
Syst em
Ignit ion T iming Cont rol Syst em
Three Way Catalytic Converter
282
——y

y
(%yy