high beam HONDA ACCORD 2006 CL7 / 7.G Owners Manual

The U.S. instrument panel is shown. Dif f erences f or the Canadian models are noted in thetext.
Instrument Panel
Inst rument s and Cont rols
57
CRUISE CONTROL INDICATOR
LOW FUEL INDICATOR
MALFUNCTION
INDICATOR LAMP
LOW OIL PRESSURE
INDICATOR SECURITY SYSTEM INDICATOR
IMMOBILIZER SYSTEM INDICATOR
ANTI-LOCK BRAKE SYSTEM
(ABS) INDICATOR
SUPPLEMENTAL
RESTRAINT SYSTEM
INDICATOR
DOOR AND TRUNK
OPEN MONITOR
CRUISE CONTROL MAIN
INDICATOR
HIGH BEAM INDICATOR
(P.58) (P.58) (P.61)
(P.61)
(P.58)
(P.62) (P.60)
(P.63)
(P.59)
(P.63)
(P.62) VSA ACTIVATION INDICATOR
(P.63)
(P.58)
CHARGING SYSTEM
INDICATOR VEHICLE STABILITY ASSIST (VSA)
SYSTEM INDICATOR
PARKING BRAKE AND BRAKE SYSTEM
INDICATOR MAINTENANCE MINDER
INDICATOR
SEAT BELT
REMINDER LIGHT
DAYTIME RUNNING LIGHTS INDICATOR SIDE AIRBAG OFF INDICATOR (P.59)
LIGHTS-ON INDICATOR
(P.60)
(P.59)
(P.60)
(P.63)
(P.59) (P.62)
 — — y y
( y   y

This indicator comes on with the
high beam headlights. For more
inf ormation, see page .
This indicator comes on when the
security system is set. See page f or more inf ormation on the
security system. When the daytime running lights
(DRL) are on, this indicator comes
on with reduced brightness.
If this indicator comes on when the
ignition switch is turned to the ON
(II) position and the parking brake is
released, it means there is a problem
in the high beam headlight’s circuit.
Have your vehicle checked by your
dealer.
144 70
U.S. EX, EX-L, LX-V6 and EX-V6
Canadian SE, EX-L, SE-V6 and EX-V6
Security System Indicator ‘‘Daytime Running Lights’’ IndicatorHigh Beam Indicator
Instrument Panel Indicators
62
SECURITY SYSTEM INDICATOR
 — — y 
y
( y  y

µ
µ µ
Turn signal
Of f
Parking and interior lights
Headlight on
High beams
Flashhighbeams Push down on the
lef t lever to signal a lef t turn and up
to signal a right turn. To signal a lane
change, push lightly on the lever in
the proper direction and hold it. The
lever will return to center when you
release it or complete a turn.
Turning the switch
on the lef t lever to the position
turns on the parking lights, taillights,
side marker lights, rear license plate
lights and lights-on indicator.
Turning the switch to the position turns on the
headlights. If you leave the lights on
with the ignition switch in
ACCESSORY (I) or LOCK (0), you
will hear a reminder chime when you
open the driver’s door.
When the light switch is in either of
these positions, the lights-on
indicator comes on as a reminder. To turn on the high
beams, push the lever f orward until
you hear a click. The blue high beam
indicator will come on (see page ).
To turn of f the high beams, pull the
lever back. To flash the high beams,
pull the lever f arther back, and then
release it. The high beams remain on
until the lever is released.
1.2.3.4.5.6. 62
Turn Signal and Headlights Turn Signal
HeadlightsHigh Beams
Turn Signal, Headlights
Inst rument s and Cont rols
69
 — — y 
y
( y  y

This f eature turns of f the headlights,
parking lights, side marker lights,
taillights, and rear license plate lights
within 15 seconds of removing the
key f rom the ignition switch and
closing the driver’s door.
This feature activates if you leave
the headlight switch in the orposition, remove the key, then
open and close the driver’s door. If you remove the key f rom the
ignition switch with the headlight
switch on, but do not open the door
and get out, the lights will turn of f
af ter 10 minutes.
The lights will turn on again when
you unlock or open the driver’s door.
If you unlock the door, but do not
open it within 15 seconds, the lights
will go off. With the driver’s door
open, you will hear a lights-on
reminder chime.
With the headlight switch off, the
high beam headlights and the high
beam indicator come on with
reduced brightness when you turn
the ignition switch to the ON (II)
position and release the parking
brake. They remain on until you turn
the ignition switch of f , even if you
set the parking brake.
The headlights revert to normal
operation when you turn them on
with the switch.
Except U.S. VP and Canadian DX-G
A utomatic L ighting Of f Feature, Daytime Running L ights
Automatic Lighting Of f Feature
Daytime Running Lights
70
 — — y y
( y  y

CONT INUED
Open the hood. To change a bulb
on the passenger’s side, undo the
two fasteners and remove the air
intake cover.Remove the electrical connector
f rom the bulb by squeezing the
connector to unlock the tab, then
slide the connector of f the bulb.Remove the bulb by turning it
approximately one-quarter turn
counterclockwise.
Install the new bulb, and turn it
one-quarter turn clockwise to lock
it in place.
1.
3.
2.
4.
Lights
High Beam Headlight
Maint enance
219
FASTENERS
4-cylinder models 6-cylinder models TAB
BULB
AIR INTAKE
COVER
FASTENERS
4-cylinder models
AIR INTAKE
COVER
 — — y  y
( y y