remote control HONDA ACCORD 2006 CL7 / 7.G Owners Manual

Î
Î
Only on vehicles equipped with navigation system. Ref er to the navigation system manual.
:
Your Vehicle at a Glance
Your Vehicle at a Glance
5
INSTRUMENT PANEL
BRIGHTNESS
MOONROOF
SWITCH HEADLIGHTS/
TURN SIGNALS
REMOTE AUDIO
CONTROLS
HORN
STEERING WHEEL
ADJUSTMENT CRUISE CONTROLS
REAR WINDOW
DEFOGGER PASSENGER AIRBAG
OFF INDICATOR
(P.31)
HAZARD
WARNING BUTTON
VSA OFF SWITCH WINDSHIELD WIPERS/
WASHERS
(P.71)
(P.69)
(P.141)
(P.94) VOICE CONTROL
SWITCHES
(P.183) (P.73) (P.72, 108)
(P.145)
(P.71)
(P.68)
 — — y y
( y   y

Î
ÎOnly on vehicles equipped with navigation system. Ref er to the navigati on system manual.
:
Controls Near the Steering Wheel
Inst rument s and Cont rols
67
WINDSHIELD
WIPERS/WASHERS
INSTRUMENT PANEL
BRIGHTNESS
MOONROOF
SWITCH
HEADLIGHTS/
TURN SIGNALS
REMOTE AUDIO
CONTROLS
HORN
STEERING WHEEL
ADJUSTMENT CRUISE CONTROLS
REAR WINDOW
DEFOGGER
PASSENGER AIRBAG
OFF INDICATOR
(P.31)
HAZARD
WARNING BUTTON
(P.71)
(P.69)
(P.141)
VOICE CONTROL
SWITCHES
(P.94)
(P.181) (P.73)(P.68)
(P.71)
(P.145)
(P.72, 108)
VSA OFF SWITCH
 — — y  
y
( y   y

You can open all of the windows
from the outside with the remote
transmitter.Press the UNLOCK button once
to unlock the driver’s door.
Press the UNLOCK button a
second time, and hold it. The
passenger’s doors unlock, and all
f our windows start to open. To
stop the windows, release the
button.
To open the windows f urther,
press the button again.
You cannot close the windows with
the remote transmitter.
The power window system has a key-
of f delay f unction. The windows will
stilloperateforupto10minutes
after you turn off the ignition switch.
Opening either f ront door cancels
the delay function. You must turn
the ignition switch to ON (II) again
bef ore you can raise or lower the
windows.
You can open and close the windows
with the key in the driver’s door lock.
To open:Turn the key clockwise, then
release it.
Insert the key in the driver’s door
lock.
1. 2. 3.
1. 2.
Power Window Control
Operations
Opening t he Windows wit h t he
Remote Transmitter
Opening/Closing t he Windows wit hthe Key
Power Windows
Inst rument s and Cont rols
93
UNLOCK BUTTON
Open
Close
 — — y 
y
( y  y

µ
Todothis,pressandholdthetwo
outside buttons on the HomeLink
transceiver for about 20 seconds,
until the red indicator f lashes.
Release the buttons, then proceed to
step 1.
The HomeLinkuniversal
transceiver built into your vehicle
canbeprogrammedtooperateupto
three remotely controlled devices
around your home, such as garage
doors, lighting, or home security
systems.
If you are training HomeLink to
operate a garage door or gate, you
should unplug the motor f or that
device during training. Repeatedly
pressing the remote control button
could burn out the motor.
HomeLink stores the code in a
permanent memory. There should
be no need to retrain HomeLink if
your vehicle’s battery goes dead or is
disconnected. If your garage door
opener was manuf actured bef ore
April 1982, you may not be able to
program HomeLink to operate it.
They do not have the saf ety f eature that causes the motor to stop and
reverse if an obstacle is detected
during closing, increasing the risk of
injury.
Always ref er to the opening
instructions and saf ety inf ormation
that came with your garage door
opener or other equipment you
intend to operate with HomeLink. If
you do not have this inf ormation,
contact the manuf acturer of the
equipment.
For quick and accurate training,
make sure the remote control
transmitter for the device (garage
door, automatic gate, security
system, etc.) has a fresh battery.
If you just
received your vehicle and have not
trained any of the buttons in
HomeLink bef ore, you should erase
any previously learned codes bef ore
training the first button.
If you are training the second or
third buttons, go directly to step 1.
Unplug the garage door opener
motor f rom the electrical outlet.
Holdtheendof thegaragedoor
opener remote 2 to 5 inches f rom
HomeLink.Makesureyouarenot
blocking your view of the red
indicator in HomeLink.
1. 2.
If equippedT raining HomeL ink
General Inf ormation Important Saf ety Precautions
Bef ore you begin
HomeL ink Universal T ransceiver
148
 — — y 
y
( y 

y

Plug in the garage door opener
motor, then test the HomeLink
button by pushing it f or about 1second.
If the button works,
programming is complete.
If the button does not work go
to step 6.
Press and hold the remote
transmitter button and one of the
HomeLink buttons at the same
time. If the red indicator in HomeLink
begins to f lash slowly at f irst,
then rapidly, release both
buttons, and go to step 5. If the red indicator in HomeLink
continues to f lash slowly (does
not f lash rapidly), your remote
transmitter may stop
transmitting after a short time.
Go to step 4.
Press and hold the remote
transmitter button and one of the
HomeLink buttons at the same
time. While continuing to hold the
HomeLink button, press and
release the remote transmitter
button every 2 seconds. If the red indicator in HomeLink
begins to f lash slowly at f irst,
then rapidly, release both
buttons, and go to step 5.
If the red indicator in HomeLink
continues to f lash slowly (does
not begin to f lash rapidly),
repeat steps 2 thru 4. Repeat these steps to train the
other two HomeLink buttons to
operate any other compatible
remotely controlled devices
around your home (lighting,
automatic gate, security system,
etc.).If the indicator f lashes rapidly
f or 2 seconds then stays on, you
have a rolling code transmitter:
Go to ‘‘Training with a Rolling
Code System’’ (see page ).
If the indicator stays on or
flashes slowly, repeat steps 2
thru 5.
PushandholdtheHomeLink
button f or a f ew seconds, then
watch the red indicator on
HomeLink.
3. 4. 5.6. 7.
150
HomeL ink Universal T ransceiver
Features
149
 — — y  y
( y 
y

For security purposes, newer garage
door opening systems use a ‘‘rolling’’
or variable code. Inf ormation f rom
the remote control and the garage
door opener are needed bef ore
HomeLink can operate the garage
door opener.Find the ‘‘training’’ button on your
garage door opener unit. The
location will vary, depending on
the manufacturer.
Make sure you have properly
completed the ‘‘Training
HomeLink’’ procedure. Press the HomeLink button again.
It should operate the garage door.
The ‘‘Training HomeLink’’
procedure trains HomeLink to the
proper garage door opener code.
The f ollowing procedure
synchronizes HomeLink to the
garage door opener so it sends and
receives the correct codes. Press the training button on the
garage door opener unit until the
indicator next to the button comes
on. The indicator may blink, or
comeonandstayon.Youthen
have approximately 30 seconds to
complete the f ollowing steps.Press and hold the button on
HomeLink f or 3 to 4 seconds.
Press and hold the HomeLink
button again f or 3 to 4 seconds.
This should turn of f the training
indicator on the garage door
opener unit. (Some systems may
require you to press the button up
to three times.)
6.
2. 4. 5.
1. 3.
T raining With a Rolling Code
System
HomeL ink Universal T ransceiver
150
TRAINING BUTTON
 — — y y
( y 
y

CONT INUED
...................
Neutral Gear Position . 174
..................
New Vehicle Break-in . 154
.....................
Normal Shif t Speeds . 171
...................
NOTICE, Explanation of . i
...............
Numbers, Identif ication . 264 ..............
Panel Brightness Control . 71
........................
Park Gear Position . 174
.................................
Parking Brake . 95
.................................
Parking Lights . 69
..
Parking Over Things that Burn . 276
..................................
Parking Tips . 178
.............................
PGM-FI System . 275
.........
Pregnancy, Using Seat Belts . 18
.........
Protecting Adults and Teens . 13
...
Additional Safety Precautions . 19
.....
Advice f or Pregnant Women . 18
........................
Protecting Children . 34
Protecting Inf ants and Small
.......................................
Children . 38
...........
Protecting Larger Children . 48
.....................
Using Booster Seat . 49
...................
Radiator Overheating . 248
Radio/CD Sound
...............
System . 118, 119, 122, 123
Rear Lights, Bulb ......................
Replacement . 222, 223 ..........................
Rear Seat, Folding . 88
............................
Rear View Mirror . 90
.................
Rear Window Def ogger . 72
...............
Reclining the Seat Backs . 86
.......
Recommended Shif t Speeds . 171
.............................
Reminder Lights . 58
.......................
Remote Transmitter . 78
Replacement Inf ormation
................
Engine Oil and Filter . 205
..........................................
Fuses . 257
................................
Light Bulbs . 218
................................
Timing Belt . 217
...........................................
Tires . 231
.............................
Wiper Blades . 225
Replacing Seat Belts Af ter a ............................................
Crash . 22
.................
Reserve Tank, Coolant . 208
...............................
Restraint, Child . 34
..........
Reverse Gear Position . 172, 174
................................
Rotation, Tire . 230
...
Octane Requirement, Gasoline . 154
.........................................
Odometer . 64
Odometer/Outside Temperature
........................................
Display . 64
Oil ........................
Change, How to . 205
......................
Change, When to . 193
......................
Checking Engine . 159
..............
Pressure Indicator . 58, 250
Selecting Proper Viscosity
......................................
Chart . 204
...........
ON (Ignition Key Position) . 76
..............................
Outside Mirrors . 90
.....................
Outside Temperature . 64
....................
Overheating, Engine . 248
....
Owner’s Maintenance Checks . 197
Index
N O P R
INDEX
V
 — — y
  
y
( y  y