HONDA ACCORD 2008 8.G Owners Manual

µ
See pages f or important saf ety
inf ormation and warnings about how toproperly position the seats and seat-
backs. 11 13
Make all seat adjustments bef ore
you start driving.
To adjust the seat f orward or
backward, pull up on the bar under
the seat cushion’s f ront edge. Move
the seat to the desired position, and
releasethebar.Trytomovetheseat
to make sure it is locked in position.To change the seat-back angle, pull
up on the lever on the outside of the
seat bottom.
Once a seat is adjusted correctly,
rock it back and f orth to make sure it
is locked in position.
FrontSeatManualAdjustments
Seats
Inst rument s and Cont rols
93
——
y


y
)yy

They are most ef f ective when you
adjust them so the center of the back
of the occupant’s head rests against
the center of the restraint.
Your vehicle is equipped with head
restraints in all seating positions to
help protect you and your
passengers f rom whiplash and other
injuries.
The height of your driver’s seat is
adjustable. To raise the seat,
repeatedly pull up the lever on the
outside of the seat cushion. To lower
the seat, push the lever down
repeatedly.
See page f or important saf ety inf ormation and a warning aboutimproperly positioning head restraints.
LX model 13
Driver’s Seat Manual Height
Adjustment
Head Restraints
Seats
94
——
y


y
)yy

The head restraints adjust f or height.
You need both hands to adjust a
restraint. Do not attempt to adjust it
while driving. To raise it, pull upward.
To lower the restraint, push the
release button sideways, and push
the restraint down.To remove a head restraint f or
cleaning or repair, pull it up as f ar as
it will go. Push the release button,
then pull the restraint out of the seat-
back.When reinstalling a head restraint,
put the legs back in place. Then
adjust it to the appropriate height
while pressing the release button.
Make sure the head restraint locks
in position when you reinstall it.
CONT INUED
Seats
A djust ing t he Head Rest raint Removing t he Head Rest raint
Inst rument s and Cont rols
95
LEGSCUSHION
RELEASE
BUTTON
Front
CUSHION
Rear Center
SEAT-BACK SEAT-BACK
LEGS RELEASE
BUTTON
Failure to reinstall the head
restraints can result in severe
injury during a crash.
Always replace the head
restraints before driving.
——
y


y
)y
y

The driver’s and f ront passenger’s
seats have active head restraints. If
the vehicle is struck severely f rom
the rear, the occupant properly
secured with the seat belt will be
pushed against the seat-back and the
head restraint will automatically
move forward.
This reduces the distance between
the restraint and the occupant’s head.
It also helps protect the occupantsagainst whiplash and injuries to the
neck and upper spine.
Af ter a collision, the activated
restraint should return to its normal
position.
If the restraints do not return to their
normal position, or in the event of a
severe collision, have the vehicle
inspected by a Honda dealer.
For a head restraint system to work
properly:
Do not hang any items on the head
restraints, or f rom the restraint
legs.
Do not place any object between
an occupant and the seat-back.
Install each restraint in its proper
location.
Only use genuine Honda
replacement head restraints.
Seats
A ct ive Head Rest raint s
96
——
y


y
)y

y

When storing cargo, you can move
therearcentershoulderbeltoutof
the way by removing the belt f rom
the guide.
The back of the rear seat folds down,
giving you direct access to the trunk.
The seat-back is released f rom inside
the trunk.
Remove any items from the seat
beforeyoufolddowntheseat-back.
Make sure the rear seat armrest is
stored.
To release the seat-back from inside
the trunk, pull the release under the
trunk panel. Push the seat-back
down f rom inside the trunk, or pull
the seat-back down f rom inside the
vehicle.
CONT INUED
Folding Rear Seat
Seats
Inst rument s and Cont rols
97
Pull
GUIDE RELEASE
——
y


y
)y
y

Make sure that the folded seat-back
does not press against the f ront
passenger’s seat, as this could cause
the weight sensors to work
improperly.Never drive with the seat-back
f olded down and the trunk lid open.
See on
page .
Make sure all rear shoulder belts are
positioned in f ront of the rear seat-
back, and the center shoulder belt is
re-positioned in the guide whenever
the seat-back is in its upright position.
Be sure there are no twists in any
shoulder belt.
Do not put any heavy items on the
seat-back when it is folded down.
Make sure all items in the trunk, or
items extending through the opening
into the back seat, are secured.
Looseitemscanflyforwardand
cause injury if you have to brake
hard. See on page
. To use the console lid as an armrest,
slide it to one of its three positions.
If the rear head restraints get caught
on the f ront seat backs and you
cannot fold down the rear seat-back
f ully, you can remove the head
restraints (see page ).
Make sure the removed head
restraints are securely stored.
To lock the seat-back upright, push it
f irmly against the trunk panel. Make
sure it is latched in place by pulling
on the top of the seat.
51
273
95
Seats
Carbon Monoxide Hazard
Carrying Cargo Armrest
98
Front
——
y

y
)y
y

The rear seat armrest is in the
center of the rear seat. Pivot it down
to use it.
A beverage holder is located in the
armrest.Never drive with this cover open and
the trunk lid open.
See on
page .
For security, this cover can be
locked and unlocked only with the
master key. To lock the cover, insert
thekeyandturnitclockwise.
Make sure all items in the trunk and
those extending through the pass-
through are secured.
The trunk pass-through cover can be
opened f rom inside the vehicle; it
f olds down onto the center armrest.
Open the cover by sliding the knob
downward and pulling on the cover.
To close the cover, swing it up and
push f irmly on the top. Make sure it
latches properly. 51
Seats
T runk Pass-through Cover
Carbon Monoxide Hazard
Inst rument s and Cont rols
99
KEY CYLINDER
LID
Rear
KNOB
——
y


y
)y
y

Both f ront seats are equipped with
seat heaters. Because of the sensors
f or the side airbag cutof f system,
there is no heater in the passenger’s
seat-back. The ignition switch must
be in the ON (II) position to use the
heaters.Push the right side of the switch, HI,
to rapidly heat up the seat. Af ter the
seat reaches a comfortable
temperature, select LO by pushing
the lef t side of the switch. This will
keep the seat warm.
In the HI setting, the heater turns off
when the seat gets warm, and turns
back on after the seat’s temperature
drops.
In the LO setting, the heater runscontinuously. It does not cycle with
temperature changes.
If the engine is lef t idling f or an
extended period, do not use the
seat heaters even on the LO
setting. It can weaken the battery,
causing hard starting.
Use the HI setting only to heat the
seats quickly, because it draws
large amounts of current f rom the
battery.
Follow these precautions whenever
you use the seat heaters:
EX-L and EX-L V6
Seat Heaters
100
Driver’s Seat
Passenger’sSeat
HEATERS
——
y


y
)y
y

The inside mirror can automatically
darken to reduce glare. To turn on
this feature, press the button on the
bottom of the mirror. The AUTO
indicator comes on as a reminder.
When it is on, the mirror darkens
when it senses the headlights of a
vehicle behind you, then returns to
normal visibility when the lights are
gone. Press the button again to turn
of f this f eature.
Keeptheinsideandoutsidemirrors
clean and adjusted f or best visibility.
Be sure to adjust the mirrors bef ore
you start driving.
The inside mirror has day and night
positions. The night position reduces
glare f rom headlights behind you.
Flip the tab on the bottom edge of
the mirror to select the day or night
position.
LX, LX-P, EX and EX V6
EX-L and EX-L V6
Mirrors
Inst rument s and Cont rols
101
AUTO BUTTON
INDICATOR SENSOR
TAB
There is also a sensor on the back of
the mirror. Items hung on the mirror
may block this sensor and af f ect its
perf ormance.
——
y

y
)y
y

Turn the ignition switch to the ON
(II) position.
Move the selector switch to L
(driver’s side) or R (passenger’s
side).Push the appropriate edge of the
adjustment switch to move the
mirrorright,left,up,ordown.
When you f inish, move the
selector switch to the center (off)
position. This turns the
adjustment switch of f to keep your
settings.
The outside mirrors are heated to
remove fog and frost. With the
ignition switch in the ON (II)
position, turn on the heaters by
pressing the button. The indicator in
the button comes on as a reminder.
Press the button again to turn the
heaters off. Pressing this button also
turns the rear window def ogger on
and off.
1. 3.
2. 4.
AllCanadianmodels
U.S. EX, EX-L, EX V6 and EX-L V6
Mirrors
PowerMirrorHeaters
Adjusting the Power Mirrors
102
SELECTOR SWITCH
ADJUSTMENT SWITCH REAR WINDOW DEFOGGER/
HEATED MIRRORS BUTTON
EX-L V6 without navigation system is
shown.
——
y

y
)y
y