indicator HONDA ACCORD 2012 8.G Repair Manual

To load or play discs, the ignition
switch must be in the ACCESSORY
(I) or ON (II) position.
You operate the disc changer with
the same controls used f or the radio.
To select the disc changer, press the
CD/AUX or CD button. You will see
‘‘CD’’ in the display. The disc and
track numbers, and the elapsed time
areshowninthedisplay.Youcan
also select the displayed inf ormation
with the TITLE button (see page). The system will continuously
play a disc until you change modes. This audio system can also play
CD-Rs and CD-RWs compressed in
MP3 or WMA f ormats. When
playing a disc in MP3, you will see
‘‘MP3’’ in the display. In WMA
f ormat, ‘‘WMA’’ will appear in the
display. You can select up to 99
f olders, or up to 255 tracks/f iles.
Video CDs and DVDs do not work in
this unit.
Depending on the sof tware the f iles
were made with, it may not be
possible to play some f iles, or display
some text data.
If a f ile on a WMA disc is protected
by digital rights management
(DRM), the audio unit displays
UNSUPPORTED, and then skips to
the next f ile. Your vehicle’s in-dash disc changer
holdsuptosixdiscs.
Press the LOAD button until you
hear a beep and see ‘‘LOAD’’ in
the display. To load only one disc,
press and release the LOAD
button.
The disc number f or an empty
position begins blinking.
Insert the disc into the disc slot
when the green disc load indicator
comes on. Insert it only about
half way; the drive will pull it in the
rest of the way. You will see
‘‘BUSY’’ in the display while the
disc load indicator turns red and
blinks as the disc is loaded.
1. 2. 3.
157EX, EX-L, Canadian SE, and V6 models
To Play a DiscL oading Discs
Playing Discs (Models without navigation system)
156
NOTE:
Do not use discs with adhesive labels.
The label can curl up and cause the
disc to jam in the unit.
Main MenuTable of Contents

CONT INUED
You cannot load and play 3-inch
(8-cm) discs in this unit.
When the disc load indicator turns
green and ‘‘LOAD’’ appears in the
display again, insert the next disc
in the slot. Do not try to insert a
disc until ‘‘LOAD’’ appears. You
could damage the audio unit.
Repeat this until all six positions
are loaded. If you are not loading
all six positions, the system begins
playing the last disc loaded.
You can also load a disc into an
empty position while a disc is playing
by pressing the appropriate preset
button. The system stops playing the
current disc and starts the loading
sequence. It then plays the disc just
loaded. Insert a disc about half way into the
disc slot. The drive will pull the disc
intherestof thewaytoplayit.You
operate the disc player with the
same controls used f or the radio.
The number of the current track is
showninthedisplay.Whenplayinga
disc in MP3 or WMA, the numbers
of the current f older and f ile are
shown. The system will continuously
play a disc until you change modes.
Each time you press the TITLE
button, the display shows you the
text, if the disc was recorded with
text data.
You can see the album, artist, and
track name in the display. If a disc is
recordedinMP3orWMA,youcan
see the f older and f ile name, and the
artist, album, and track tag.
With the f older name, you will see
the FOLDER indicator in the display.
The TRACK indicator is shown with
the file or track name.
You cannot load and play 3-inch
(8-cm)discsinthissystem.
For inf ormation on how to handle
and protect compact discs, see page
. When you press and release the
TITLE button while a disc without
text data is playing, you will see ‘‘NO
INFO’’ on the display.
The display shows up to 16
characters of selected text data (the
f older name, f ile name, etc.).
4. 5.
237
LX, LX-P, and U.S. SE models
Playing Discs (Models without navigation system)
To Load a Disc Text Data Display Function
Features
157
Main MenuTable of Contents

Use the SKIP bar while a disc is
playing to select passages and
change tracks (f iles in MP3 or WMA
mode).
In MP3 or WMA mode, use the
FOLDERbar(CATEGORYbaron
models with XM Radio) to select
f olders in the disc and use either
side of the skip bar to change f iles.
To select a dif f erent disc, use the
appropriate preset buttons (1
through 6). If you select an empty
position, the system will go into the
loading sequence (see page ).
You will also see some text data
under these conditions:
When a new f older, f ile, or track is
selected.
When you change the audio mode
to play a disc with text data or in
MP3 or WMA.
When you insert a disc, and the
system begins to play.
When playing a CD-DA with text
data, the album and track name are
showninthedisplay.Withadiscin
MP3 or WMA, the display shows the
f older and f ile name.
When you turn on the audio system
next time, the system keeps your
selection with the TITLE button.
If the text data has more than 16
characters, you will see the f irst 16
characters and the indicator in
the display. Press and hold the
TITLE button until the next 16
characters are shown. You can see
up to 32 characters of the text data.
If youpressandholdtheTITLE
button again, the display shows the
f irst 16 characters again.
If any letter is not available, it is
replaced with ‘‘ . ’’ (dot) in the display.
When the disc has no text data, you
will see ‘‘NO INFO’’ on the display.
156
EX, EX-L, Canadian SE, and V6 models
T o Change or Select T racks/Files
Playing Discs (Models without navigation system)
158
Main MenuTable of Contents

Playing an iPod(Models without navigation system)
EX,EX-L,CanadianSE,andV6models
Without XMRadioWith XMRadio
166
SKIP BAR
TITLE BUTTON
PRESET
BUTTONS
MENU BUTTONSKIP BAR
TITLE BUTTON
CD/AUX BUTTON
U.S. models are shown. POWER/VOLUME KNOB
POWER/VOLUME KNOB
SELECTOR KNOB
MENU BUTTON
SELECTOR KNOB RETURN BUTTON
RETURN BUTTON AUX BUTTON
iPod INDICATOR iPod INDICATOR
Main MenuTable of Contents

Playing an iPod(Models without navigation system)
Without XMRadio
Features
U.S.LX,LX-P,andU.S.SEmodels
167
TITLE BUTTON
SKIP BAR
MENU BUTTON
SELECTOR KNOB
RETURN BUTTON PRESET BUTTONS
POWER/VOLUME KNOB
AUX BUTTON
iPod INDICATOR
Main MenuTable of Contents

Pull out the USB connector f rom
the holder.Connect your dock connector to
the iPod correctly and securely.
Install the dock connector to the
USB adapter cable securely.If the iPod indicator does not appear
in the audio display, check the
connections, and try to reconnect the
iPod a f ew times.
If the audio system still does not
recognize the iPod, the iPod may
need to be reset. Follow the
instructions that came with your
iPod, or you can f ind reset
instructions online at
1. 2. 3.
www.apple.com/
CONT INUED
Connect ing an iPod
Playing an iPod(Models without navigation system)
Features
169
DOCK CONNECTOR
USB CONNECTOR
USB CONNECTOR
USB ADAPTER CABLE
Main MenuTable of Contents

µ
Each time you press the TITLE
button the display mode switches
between the album name, the song
name, the artist name, or name of f
(which turns off the text display).
If the text data has more than 16
characters, you will see the f irst 16
characters and the indicator in
the display. Press and hold the
TITLE button until the next 16
characters are shown. You can see
up to 32 characters of the text data. Use the SKIP bar while an iPod is
playing to select passages and
change f iles.
Each time you press and
releasethe sideof theSKIPbar,
the system skips forward to the
beginning of the next f ile. Press and
releasethe sideof thebarto
skip backward to the beginning of
the current f ile. Press it again to skip
to the beginning of the previous file.
To move rapidly within a f ile, press
andholdeitherside( or )
of the SKIP bar.
Turning the selector knob to the
right or the lef t also changes the f ile. You can also select a file from any
list on the iPod menu: playlists,
artists, albums and songs, by using
the selector knob. Push the selector
knob (ENTER) to switch the display
to an iPod menu, then turn the
selector knob to select a desired list.
Press ENTER to set your selection.
T ext Dat a Display Funct ion T o Change or Select Files T o Select a File f rom iPod Menu
SK IP
Playing an iPod(Models without navigation system)
170
Push ENTER.
Main MenuTable of Contents

Playing a USB Flash Memory Device (Models without navigation system)
EX,EX-L,CanadianSE,andV6models
Without XMRadioWith XMRadio
176
SCAN
BUTTON
MENU BUTTONSKIP BAR SCAN
BUTTON
MENU BUTTONSKIP BAR
TITLE BUTTON
U.S. models are shown. FILE TYPE INDICATOR AUX BUTTON
FILE TYPE INDICATOR
USB INDICATOR
TITLE BUTTON
CD/AUX BUTTON
SELECTOR KNOB
RETURN BUTTON
CATEGORY BAR
RETURN BUTTON
SELECTOR KNOB
FOLDER BAR USB INDICATOR
POWER/VOLUME KNOB
POWER/VOLUME KNOB
Main MenuTable of Contents

Playing a USB Flash Memory Device (Models without navigation system)
Without XMRadio
Features
U.S.LX,LX-P,andU.S.SEmodels
177
TITLE BUTTON
SKIP BAR
SCAN BUTTON
FOLDER BAR
MENU BUTTON
SELECTOR KNOB
RETURN BUTTON AUX BUTTON
POWER/VOLUME KNOB
USB INDICATOR
FILE TYPE INDICATOR
Main MenuTable of Contents

Connect the USB f lash memory
device to the USB adapter cable
correctly and securely.
When the USB f lash memory device
is connected, the USB indicator is
showninthedisplay. Each time you press the TITLE
button, the display mode shows you
in sequence, the f older name, the f ile
name, the artist name, the album
name, the song name, or name of f
(which turns off the text display).
Pull out the USB connector f rom
the holder. If the text data has more than 16
characters, you will see the f irst 16
characters and the indicator in
the display. Press and hold the
TITLE button until the next 16
characters are shown. You can see
up to 32 characters of the text data.
1. 2.
Connect ing a USB Flash Memory
Device T ext Dat a Display Funct ion
Playing a USB Flash Memory Device (Models without navigation system)
180
USB CONNECTOR
USB ADAPTER CABLE
USB CONNECTOR
Main MenuTable of Contents