ECU HONDA ACCORD 2016 9.G Quick Guide

2 || 3
SAFETYVISUAL INDEX
Dashboard and Other Controls
1  Audio system/touchscreen*/   
 navigation* system  p. 54, p. 79,
p. 87
2  Hazard warning button
3 Climate control system p. 46
4  Seat heater switches*   p. 47
5 USB port p. 50
Wireless charger*   p. 51
Accessory power socket p. 50
6 rearview mirror p. 44
7 Power window switches p. 33
Door lock switches p. 32
Door mirror controls p. 45
8 Fuel fill door release handle
p. 115
Trunk release button   p. 32
9 Shift lever p. 101
10 Hood release handle p. 133
11 Driving Position Memory System
 buttons*   p. 43
*if equipped
SAFETY INFORMATION
2
4
71
8
6
3
Your safety—and the safety of others—is very important, and operati\
ng this vehicle
safely is an important responsibility. While we strive to help you make informed 
decisions about safety, it is not practical or possible to warn you about all the 
hazards associated with operating or maintaining your vehicle. Therefore, you must 
use your own good judgment.
Important Safety Information
This guide explains many of your vehicle’s safety features and how to use them.
Please read this information carefully. Following the instructions below will also help 
to keep you and your passengers safe.
Important Safety Precautions
• 
Always wear your seat belt.
•  Secure all children in the proper restraint system.
• 
Be aware of airbag hazards.
•  Don’t drink and drive.
•  Pay appropriate attention to the task of driving safely.
•  Control your speed.
•  Keep your vehicle in safe condition.
engaging in cell phone conversation or other activities that keep you fro\
m paying
close attention to the road, other vehicles, and pedestrians could lead \
to a crash.
Remember, situations can change quickly, and only you can decide when it is safe 
to divert some attention away from driving.
Safety Messages
When you see the following messages throughout this guide, pay close attention.
You WILL be KILLED or SERIOUSLY HURT if you don’t follow    
instructions.
You CAN be KILLED or SERIOUSLY HURT if you don’t follow    
instructions.
You CAN be HURT if you don’t follow instructions.
This information is intended to help you avoid damage to your
vehicle, other property, or the environment.
DANGER
WARNING
CAUTION
NOTICE
5910
11

6 || 7
SAFETYSAFETY
Seat Belt Inspection
Regularly check the condition of your seat belts as follows: 
• Pull each belt out fully, and look for frays, cuts, burns, and wear.
• Check that the latches work smoothly and the belts retract easily. If a belt does 
not retract easily, cleaning the belt may correct the problem. Use only mild soap 
and warm water. Do not use bleach or cleaning solvents. Make sure the belt is 
completely dry before allowing it to retract.
Any belt that is not in good condition or working properly will not provide proper 
protection and should be replaced as soon as possible.
A belt that has been worn during a crash may not provide the same level of 
protection in a subsequent crash. Have your seat belts inspected by a dealer after 
any collision.
Fastening a Seat Belt
Adjust your seat to the proper position (see page 39), and then follow the below 
steps.
1. Pull the seat belt out slowly.
2. Insert the latch plate into the buckle, then tug 
on the belt to make sure the buckle is secure. 
Make sure that the belt is not twisted or caught 
on anything.
3. Position the lap part of the belt as low as possible 
across your hips, then pull up on the shoulder
part of the belt so the lap part fits snugly. This lets 
your strong pelvic bones take the force of a crash 
and reduces the chance of internal injuries.
4. If necessary, pull up on the belt again to remove 
any slack, then make sure that the belt rests 
across the center of your chest and over your
shoulder. This spreads the forces of a crash over
the strongest bones in your upper body.
 To release the belt, push the red PRESS button 
then guide the belt by hand until it has retracted 
completely.
Adjusting the Shoulder Anchor
The front seats have adjustable shoulder anchors to accommodate taller and 
shorter occupants.
1. Move the anchor up and down while holding the
release button.
2. Position the anchor so that the belt rests across 
the center of your chest and over your shoulder.
Not checking or maintaining seat belts can result in serious injury or death if 
the seat belts do not work properly when needed.
Check your seat belts regularly and have any problem corrected as soon as 
possible.
WARNING
Pull out slowly.
Lap belt as low as
possible.
Latchplate
Buckle
Improperly positioning the seat belts can cause serious injury or death in a 
crash.
Make sure all seat belts are properly positioned before driving.
WARNING
Push

14 || 15
SAFETYSAFETY
Child Safety
Each year, many children are injured or killed in vehicle crashes because they are 
either unrestrained or not properly restrained. In fact, vehicle collisions are the 
number one cause of death of children ages 12 and under.
The National Highway Traffic Safety Administration and Transport Canada
recommend that all children ages 12 and under be properly restrained in a rear seat. 
Some states or provinces/territories have laws restricting where children may ride. 
To reduce the number of child deaths and injuries, every state, Canadian province 
and territory requires that infants and children be properly restrained when they ride 
in a vehicle.
Protecting Child Passengers
• 
An inflating front or side airbag can injure or kill a child sitting in the front seat.
• A child in the front seat is more likely to interfere with the driver’s ability to 
safely control the vehicle.
• 
Statistics show that children of all sizes and ages are safer when they are 
properly restrained in a rear seat.
• 
Any child who is too small to wear a seat belt correctly must be restrained in an 
approved child seat that is properly secured to the vehicle using either\
the lap
belt portion of the lap/shoulder belt or the lower anchors of the LATCH system.
• Never hold a child on your lap because it is impossible to protect them in the 
event of a collision.
• 
Never put a seat belt over yourself and a child. During a crash, the belt would 
likely press deep into the child and cause serious or fatal injuries.
• 
Never let two children use the same seat belt. Both children could be very 
seriously injured in a crash.
•  Do not allow children to operate the doors, windows, or seat adjusters.
•  Do not leave children in the vehicle unattended, especially in hot weath\
er when
the inside of the vehicle can get hot enough to kill them. They could al\
so activate
vehicle controls, causing it to move unexpectedly.
Protecting Infants
An infant must be properly restrained in a rear-facing, reclining child seat until the 
infant reaches the seat maker’s weight or height limit for the seat, and the infant
is at least one year old. Many experts recommend use of a rear-facing seat for
a child up to two years old if the child’s height and weight are appropriate for a
rear-facing seat.
Child seats must be placed and secured in a rear 
seating position. rear-facing child seats should
never be installed in a forward-facing position.
When properly installed, a rear-facing child seat may prevent the driver or a front 
passenger from moving their seat all the way back, or from locking their seat-back 
in the desired position. If this occurs, we recommend that you install the child 
seat directly behind the front passenger’s seat, move the seat as far forward as 
needed, and leave it unoccupied. or, you may wish to get a smaller rear-facing
child seat.
Allowing a child to play with a seat belt or wrap one around their neck can 
result in serious injury or death.
Instruct children not to play with any seat belt and make sure any unused 
seat belt a child can reach is buckled, fully retracted, and locked.
WARNING
Children who are unrestrained or improperly restrained can be seriously 
injured or killed in a crash.
Any child too small for a seat belt should be properly restrained in a child 
seat. A larger child should be properly restrained with a seat belt, using a 
booster seat if necessary.
WARNING
Placing a rear-facing child seat in the front seat can result in serious injury or
death during a crash.
Always place a rear-facing child seat in the rear seat, not the front.
WARNING

16 || 17
SAFETYSAFETY
Protecting Smaller Children
If a child is at least one year old and within the weight range indicated by the child 
seat manufacturer, the child should be properly restrained in a firmly secured 
forward-facing child seat.
We strongly recommend placing a forward-facing 
child seat in a rear seating position.
Placing a forward-facing child seat in the front seat
can be hazardous, even with advanced front airbags 
that automatically turn the passenger’s front airbag 
off. A rear seat is the safest place for a child.
Selecting a Child Seat
Most child seats are LATCH-compatible (Lower Anchors and Tethers for CHildren). 
Some have a rigid-type connector, while others have a flexible-type connector. 
Both are equally easy to use. Some existing and previously owned child seats can 
only be installed using the seat belt. Whichever type you choose, follow the child 
seat manufacturer’s use and care instructions as well as the instructions in this
manual. Proper installation is key to maximizing your child’s safety.
In seating positions and vehicles not equipped with LATCH, a LATCH-compatible 
child seat can be installed using the seat belt and a top tether for added security. 
This is because all child seats are required to be designed so that they can be 
secured with a lap belt or the lap part of a lap/shoulder belt. In addition, the 
child seat manufacturer may advise that a seat belt be used to attach a LATCH-
compatible seat once a child reaches a specified weight. Please read the child 
seat owner’s manual for proper installation instructions.
Important considerations when selecting a child seat
Make sure the child seat meets the following three requirements:
• The child seat is the correct type and size for the child.
• The child seat is the correct type for the seating position.
• 
The child seat is compliant with Federal Motor vehicle Safety Standard 213 or
Canadian Motor vehicle Safety Standard 213.
Installing a LATCH-Compatible Child Seat
A LATCH-compatible child seat can be installed in either of the two outer rear 
seats. A child seat is attached to the lower anchors with either the rigid or flexible 
type of connectors.
1. Locate the lower anchors under the marks.
2. Place the child seat on the vehicle seat, then
attach the child seat to the lower anchors
according to the instructions that came with the
child seat. Make sure that the lower anchors
are not obstructed by the seat belt or any other 
object.
3. Open the tether anchor cover behind the head 
restraint.
4. raise the head restraint to its highest position,
then route the tether strap between the head 
restraint legs, and secure the tether strap hook
onto the anchor.
5. Tighten the tether strap according to the seat
maker’s instructions.
6. Make sure the child seat is firmly secured by 
rocking it forward and back and side to side; little 
movement should be felt.
7. Make sure any unused seat belt that a child 
can reach is buckled, the lockable retractor 
is activated, and the belt is fully retracted and 
locked.
Placing a forward-facing child seat in the front seat can result in seri\
ous
injury or death if the front airbag inflates.
If you must place a forward-facing child seat in front, move the vehicle seat 
as far back as possible, and properly restrain the child.
WARNING
Anchor
Tether
strap hook
Marks
Rigid type
Lower anchors
Flexible
type

18 || 19
SAFETYSAFETY
Installing a Child Seat with a Lap/Shoulder Seat Belt
1. Place the child seat on the vehicle seat.
2. Route the seat belt through the child seat 
according to the seat manufacturer’s
instructions, and insert the latch plate into the
buckle. Insert the latch plate fully until it clicks.
3. Slowly pull the shoulder part of the belt all the 
way out until it stops. This activates the lockable 
retractor.
4. Let the seat belt completely wind up into the 
retractor, then try to pull it out to make sure the
retractor is locked. If you are able to pull the 
shoulder belt out, the lockable retractor is not 
activated. Pull the seat belt all the way out, and 
repeat steps 3 – 4.
5. Grab the shoulder part of the seat belt near the 
buckle, and pull up to remove any slack from 
the lap part of the belt. When doing this, place 
your weight on the child seat and push it into the
vehicle seat.
6. Make sure the child seat is firmly secured by 
rocking it forward and back and side to side; little 
movement should be felt.
7. Make sure any unused seat belt that a child 
can reach is buckled, the lockable retractor 
is activated, and the belt is fully retracted and 
locked.
 To deactivate a lockable retractor, release the buckle and allow the seat belt to 
wind up all the way.
Adding Security with a Tether
A tether anchorage point is provided behind each rear seating position. A child 
seat that is installed with a seat belt and comes with a tether can use the tether 
for additional security.
1. Locate the appropriate tether anchorage point
and lift the cover.
2. raise the head restraint to its highest position,
then route the tether strap through the head
restraint legs. Make sure the strap is not twisted.
3. Secure the tether strap hook onto the anchor.
4. Tighten the tether strap according to the seat
manufacturer’s instructions.
Tether anchorage points
Cover
Anchor
Outer positi on
Tether strap hook
Anchor
Center positionTether strap
hook
Anchor

20 || 21
SAFETYSAFETY
Protecting Larger Children
When a child is too big for a child seat, secure the child in a rear seat using the 
lap/shoulder seat belt.
Have the child sit upright and all the way back, then ensure the following:
• The child’s knees bend comfortably over the edge 
of the seat.
• 
The shoulder belt crosses between the child’s 
neck and arm.
• 
The lap part of the seat belt is as low as possible, 
touching the child’s thighs.
•  The child can stay seated for the whole trip.
If a lap/shoulder belt cannot be used properly, position the child in a booster seat 
in a rear seating position. For the child’s safety, check that the child meets the
booster seat manufacturer’s recommendations.
Some U.S. states and Canadian provinces/territories require children to use a 
booster seat until they reach a given age or weight (e.g., 6 years or 60 lbs). Be sure 
to check current laws in the state or province/territory where you intend to drive.
Safety Label Locations
Safety labels are in the locations shown. They warn you of potential hazards that 
can cause serious injury or death. Read these labels carefully.
Sun visor
U.S. models Canadian models
Radiator cap
U.S. models only
Dashboard
Allowing a child age 12 or under to sit in the front can result in injur\
y or death
if the passenger’s front airbag inflates.
If a larger child must ride in front, move the vehicle seat as far to the rear as 
possible, then have the child sit up properly and wear the seat belt properly, 
using a booster seat if needed.
WARNING

42 || 43
VEHICLE CONTROLSVEHICLE CONTROLS
Folding Down the Rear Seats
The rear seat-back(s*) can be folded down to make room for large items in the 
trunk.
1. Remove the center shoulder belt from the guide.
2. Pull the release lever in the trunk to release the
lock.
3. Fold down the seat-back. Remove the rear head 
restraints if necessary (see page 41).
Push the seat-back up firmly until it locks into 
place to return it to its original position.
Make sure all items in the trunk or items extending through the opening \
into
the rear seats are properly secured. Loose items can fly forward if yo\
u have to
brake hard.
*if equipped
Guide
Center
shoulder belt
Release
lever
Release
lever*
Adjusting the Steering Wheel
The steering wheel height and distance from your body can be adjusted so that you 
can comfortably grip the steering wheel in an appropriate driving posture.
1. Pull up the steering wheel adjustment lever.
2. Move the steering wheel up or down, and in
or out.
3. Push down the steering wheel adjustment
lever to lock the steering wheel in position.
To adjus t
To lock
Lever
Adjusting the steering wheel position while driving may cause you to los\
e
control of the vehicle and be seriously injured in a crash.
Adjust the steering wheel only when the vehicle is stopped.
WARNING
Driving Position Memory System*
You can store two driver’s seat positions into memory when the vehicle is on using
the buttons on the driver’s door.
1. Adjust the seat to your preferred position.
2. Press SeT.
3. Press and hold memory button 1 or 2. You will hear 
two beeps when the memory is set.
4. Press one of the memory buttons to recall 
previously stored positions.
Lumbar positions cannot be stored.
When you unlock and open the driver’s door with a remote transmitter, the seat 
adjusts automatically to one of the two preset positions.
Memory
button 1
Memory
button 2
SET button
*if equipped

44 || 45
VEHICLE CONTROLSVEHICLE CONTROLS
Adjusting the Mirrors
Adjust the angle of the mirrors for the best visibility when you are sitting in the 
correct driving position.
Rearview Mirror with Day/Night Positions*
Manually adjust the position to reduce headlight
glare from vehicles behind you. Flip the tab to 
switch between day and night positions.
Automatic Dimming Rearview Mirror*
When driving after dark, the automatic dimming 
function reduces the glare from headlights behind 
you.
The function cancels when the shift lever is in
reverse (r).
Power Door MirrorsAdjust the power door mirrors when the vehicle is on.
L/R selector switch: Select the left or right mirror.
After adjusting the mirror, return the switch to the
center position.
Mirror position adjustment switch: Press the switch
left, right, up, or down to move the mirror.
Selector switch
Adjustment switch
Tab
Daytime
position
Night position
HomeLink® Garage Opener*
Program your vehicle to operate up to three remote-controlled devices ar\
ound
your home—such as garage doors, lighting, or home security systems—\
using the
buttons on the ceiling.
Training a ButtonPark near the system you want to program, and follow the instructions in\
the
flowchart below.
To retrain a button or erase codes, see the Owner’s Manual on the Owner 
Information CD or at owners.honda.com (U.S.) or www.myhonda.ca (Canada).
If you need help, visit www.homelink.com or call (800) 355-3515.
Press and release the HomeLink
button. Press and release the button on
the remote every 2 seconds.
Does the LED change from slowly blinking
to constantly on or rapidly blinking? This
should take less than one minute.
Press and hold the
HomeLink button
again. Training
complete
YES
NO
HomeLink indicator
rapidly blinks. HomeLink LED
remains on.
YES
NO
YES
NO
Position the remote transmitter you wish
to link 1–3 inches (3–8 cm) from the
HomeLink button you want to program.1
Press and release the desired HomeLink
button. Hold the button on the remote
transmitter.
Does the HomeLink indicator (LED) change
from slowly blinking to constantly on or
rapidly blinking? This should take less than
one minute.
2
aThe remote has a rolling code. Press the
“learn” button on the remote-controlled
device (e.g., garage door opener) .
Press and hold the HomeLink button
again; the remote-controlled device
should operate. Within 30 seconds, press and hold the
programmed HomeLink button for
2 seconds.a
Press and hold the programmed HomeLink button for about a second.Does the device (garage door opener) work?
3
b
4
5
*if equipped
Indicator
Buttons
Sensor
JG
FRVJQQFE

94 || 95
DRIVING
DRIVING
DRIVING
Learn about preparation for driving, as well as other features.
Before Driving
Check the following items before you begin driving.
Exterior Checks
• 
Make sure there are no obstructions on the windows, door mirrors, exterior 
lights, or other parts of the vehicle.
• 
remove any frost, snow, or ice.
•  Make sure the hood is securely closed.
• 
Heat from the engine and exhaust can ignite flammable materials left under 
the hood, causing a fire. If you’ve parked your vehicle for an extended period, 
inspect and remove any debris that may have collected, such as dried grass 
and leaves that have fallen or have been carried in for use as a nest by a small 
animal. Also check under the hood for leftover flammable materials after you or 
someone else has performed maintenance on your vehicle.
•  Make sure the tires are in good condition.
• 
Make sure there are no people or objects behind or around the vehicle.
Interior Checks • 
Store or secure all items on board properly.
• Do not pile items higher in the cargo area than the seat-back height.
•  Do not place anything in the front seat footwells. Make sure to secure t\
he floor
mats.
• 
If you have any animals on board, do not let them move freely around in the 
vehicle.
•  Securely close and lock all doors and the trunk.
•  Adjust your seating position, mirrors, and steering wheel properly.
• 
Make sure items placed on the floor behind the front seats cannot roll under the 
seats.
• 
Everyone in the vehicle must fasten their seat belt.
•  Make sure that the indicators in the instrument panel come on when you s\
tart
the vehicle, and go off soon after.
If the doors are frozen shut, use warm water around the door edges to melt any 
ice. Do not try to force them open, as this can damage the rubber trim around the 
doors. When done, wipe dry to avoid further freezing.
NOTICE
In addition:
•  During the first 600 miles (1,000 km) of operation, avoid sudden acc\
eleration or
full throttle operation so as not to damage the engine or powertrain.
• 
Avoid hard braking for the first 200 miles (300 km). You should also follow this 
when the brake pads are replaced.
Improper accessories or modifications can affect your vehicle’s handling, and 
stability, and performance, and cause a crash in which you can be seriously 
hurt or killed.
Follow all instructions in the vehicle owner’s manual regarding accessories
and modifications.
WARNING

98 || 99
DRIVING
DRIVING
Towing a Trailer
Your vehicle can tow a trailer if you carefully observe the load limits, use the proper 
equipment, and follow the towing guidelines. Check the load limits before driving 
(see page 96).
Total Trailer Weight
Maximum allowable weight of the trailer, cargo, and 
everything in or on it must not exceed 1,000 lbs (450 
kg). Towing loads in excess of this can seriously
affect vehicle handling and performance and can
damage the engine and drivetrain.
Tongue Load
The weight of the tongue with a fully loaded trailer
on the hitch should be approximately 10% of the 
total trailer weight.
• 
excessive tongue load reduces front tire traction
and steering control. Too little tongue load can
make the trailer unstable and cause it to sway.
• To achieve a proper tongue load, start by loading 
60% of the load toward the front of the trailer and 
40% toward the rear. Readjust the load as needed.
Pre-tow Checklist
When preparing to tow, and before driving away, ensure the following:
• The vehicle has been properly serviced, and the suspension and the cooling 
system are in good operating condition.
•  Avoid towing a trailer during your vehicle’s first 600 miles (1,000 km).
• 
The trailer has been properly serviced and is in good condition.
•  All weights and loads are within limits. Never exceed the gross weight r\
atings.
• 
Check if all loads are within limits at a public scale. If a public scale is not 
available, add the estimated weight of your cargo load to the weight of your 
trailer (as quoted by the manufacturer) and the tongue load.
•  The hitch, safety chains, and any other attachments are secure.
•  All items in or on the trailer are properly secured and cannot shift whi\
le you drive.
exceeding any load limit or improperly loading your vehicle and trailer c\
an
cause a crash in which you can be seriously hurt or killed.
Check the loading of your vehicle and trailer carefully before starting to drive.
WARNING
To ngue Load
Total load
Tongue LoadTongue load
Remote Engine Start*
Start your vehicle’s engine using the remote transmitter before you enter the vehicle.
Make sure the vehicle is in a safe location when using remote engine start (i.e., a
well-ventilated area, away from any flammable materials).
Starting the Engine
Press the Lock button, then press and hold the Engine button within 5 seconds to 
remotely start the engine.
The engine runs for up to 10 minutes. To extend the run time for another 10
minutes, repeat the procedure during the initial 10 minutes.
While the engine is running, the climate control system adjusts the cabin 
temperature, the security system remains on, and lights and accessories remain
off.
Stopping the Engine
Press and hold the Engine button.
The engine will also stop if it has been running for more than 10 minutes, or if any 
door is opened without using the remote or smart entry.
Engine exhaust contains toxic carbon monoxide gas.
Breathing carbon monoxide can kill you or cause unconsciousness.
Never use the remote engine starter when the vehicle is parked in a gara\
ge or
other area with limited ventilation.
WARNING
Lock button
Engine button
*if equipped