light HONDA ACCORD COUPE 2002 CL7 / 7.G Manual Online

Let the engine run f or several
minutes and check the drain bolt
and oil f ilter f or leaks.
Turn of f the engine, let it sit f or
several minutes, then check the oil
level. If necessary, add oil to bring
the level to the upper mark on the
dipstick.
Put a new washer on the drain bolt,
then reinstall the drain bolt.
Tighten it to:
Replace the engine oil f ill cap.
Start the engine. The oil pressure
indicator light should go out within
f ive seconds. If it does not, turn of f
the engine and reinspect your
work.
Refill the engine with the recom-
mended oil.
Engine oil change capacity
(including f ilter): 9. 8. 7.
6. 5.
(Special Edition, EX, and U.S. LX)
(EX-V6 and the U.S. LX-V6) (EX-V6 and the U.S. LX-V6) (Special Edition, EX, and U.S. LX)
Engine Oil
Maint enance252
33 lbf·ft (44 N·m , 4.5 kgf·m)
29 lbf·ft (39 N·m , 4.0 kgf·m)
4.5 US qt (4.3
, 3.8 Imp qt)
4.6 US qt (4.4
, 3.9 Imp qt) Improper disposal of engine oil can be
harmf ul to the environment. If you
change your own oil, please dispose of
the used oil properly. Put it in a sealed
container and take it to a recycling
center. Do not discard it in a trash bin
or dump it on the ground.

Check the level in the windshield
washer reservoir at least monthly
during normal usage. In bad weather,
when you use the washers of ten,
check the level every time you stop
for fuel.
The windshield washer reservoir is
located behind the driver’s side
headlight.
The windshield washer reservoir is
located behind the passenger’s side
headlight.
The low washer level indicator will
light when the level is low (see page).
Check the reservoir’s f luid level by
removing the cap and looking at the
level gauge attached to the cap. Fill the reservoir with a good-quality
windshield washer f luid. This
increases the cleaning capability and
prevents f reezing in cold weather.
When you ref ill the reservoir, clean
the edges of the windshield wiper
blades with windshield washer f luid
on a clean cloth. This will help to
condition the blade edges.
62
4-cylinder models
6-cylinder modelsOn Canadian models
Windshield Washers
Maint enance260
L LEE V
V E
EL
L G
GAAU
UG GEE
4
4- -c
cy yl liinn d
de
err m
m o
od
de
ellss 6
6--c
cy yl liinn d
de
err m
m o
od
de
ellss
L
LE
E V
V E
EL
L G
GAAU
UG GEE
Do not use engine antif reeze or a
vinegar/water solution in the
windshield washer reservoir.
Antif reeze can damage your car’s paint,
while a vinegar/water solution can
damage the windshield washer pump.
Use only commercially-available
windshield washer f luid.

Run the air conditioning at least once
a week during the cold weather
months. Run it f or at least ten
minutes while you are driving at a
steady speed with the engine at
normal operating temperature. This
circulates the lubricating oil con-
tained in the ref rigerant.If the air conditioning does not get as
cold as before, have your dealer
check the system. Recharge the
system with Ref rigerant HFC-134a
(R-134a). (See Specif ications on
pages and .)
Your car’s air conditioning is a sealed
system. Any major maintenance,
such as recharging, should be done
by a qualif ied mechanic. You can do
a couple of things to make sure the
air conditioning works ef f iciently.
Periodically check the engine’s
radiator and air conditioning
condenser f or leaves, insects, and
dirt stuck to the f ront surf ace. These
block the air f low and reduce cooling
ef f iciency. Use a light spray f rom a
hose or a sof t brush to remove them. 344 346
Maint enance
A ir Condit ioning Syst em
279
A A
I
IRR C
COON NDDI
ITT I
IOON NIINNG G
C
CO ON NDDE
EN
NS SEER
R
Whenever you have the air conditioning
system serviced, make sure the service
f acility uses a ref rigerant recycling
system. This system captures the
ref rigerant f or reuse. Releasing
ref rigerant into the atmosphere can
damage the environment.
The condenser and radiator f ins bend
easily. Only use a low-pressure spray
or sof t-bristle brush to clean them.

Check the operation of your car’s
exterior lights at least once a month.
A burned out bulb can create an
unsaf e condition by reducing your
car’s visibility and the ability to
signal your intentions to other
drivers.
Lights
Maint enance288
H HE
EA
A D
DL
LIIGGH HT
T H
HI
IGGH H B
BEEA
A M
M
T
TU
UR RNN S
SIIGGN NAAL
L//S
SI IDD E
E
M
M A
AR
RKKEER
R L
LIIGGH HT
T
H
H
E
EA
A D
DL
LIIGGH HT
T L
LOOW W B
BEEA
A M
M
P
P A
A R
RKKIINNG G L
LIIGGH HT
T

Check the f ollowing:Headlights (low and high beam)
Parking lights
Taillights
Brake lights
High-mount brake light
Turn signals
Back-up lights
Hazard light f unction
License plate light
Side marker lights
Daytime running lights
(Canadian models)
If you f ind any bulbs are burned out,
replace them as soon as possible.
Refer to the chart on pages and to determine what type of
replacement bulb is needed. 347 345
Lights
Maint enance289
T T
U
UR RNN S
SIIGGN NAAL
L//T
T A
A I
ILLL LIIGGH HT
T H
HI
IGGH H-
-M
M O
OUUNNTT B
BRRAA K
KEE L
LIIGGH HT
T
B
BA A C
CKK--U
UP P L
LIIGGH HT
T
R
RE EA
A R
R S
SIIDD E
E M
M A
AR
RKKEER
R L
LIIGGH HT
T S
STTO
OP P/
/T
T A
A I
ILLL LIIGGH HT
T L
LI
ICCE EN
NS SEE
P
P L
LAA T
TE
E L
LIIGGH HT
TS
S

Your car has two bulbs on each side,
four in total. Make sure you are
replacing the bulb that is burned out.
Your car uses halogen headlight
bulbs. When replacing a bulb, handle
it by its plastic case and protect the
glass from contact with your skin or
hard objects. If you touch the glass,
clean it with denatured alcohol and a
clean cloth.
Theheadlightswereproperlyaimed
when your car was new. If you
regularly carry heavy items in the
trunk or pull a trailer, readjustment
may be required. Adjustment of the
headlights should be perf ormed by a
Honda technician or other qualif ied
mechanic.
Open the hood.
If you need to change the head-
light bulb on the passenger’s side,
remove the radiator reserve tank
and the air intake duct.
If you need to change the
headlight bulb on the driver’s side,
remove the radiator reserve tank.
1.
4-cylinder models
6-cylinder models
Replacing a Headlight Bulb
Headlight A iming
Lights
Maint enance290
4 4- -c
cy yl liinn d
de
err m
m o
od
de
ellss A
A
I
IRR I
INNT TA
A K
KEE
D
D U
UC CTT
Halogen headlight bulbs get very hot
when lit. Oil, perspiration, or a scratch
on the glass can cause the bulb to
overheat and shatter.

Remove the electrical connector
f rom the bulb by squeezing the
connector to unlock the tab, then
slide the connector of f the bulb.
Remove the bulb by turning it
approximately one-quarter turn
counterclockwise.Reinstall the radiator reserve tank. (Driver’s side) Reinstall the radiator reserve tank
and the air intake duct. (Passenger’s side) Turn on the headlights to test the
new bulb. Push the electrical connector back
onto the bulb. Make sure it is on
all the way. Insert the new bulb into the hole
and turn it one-quarter turn clock-
wise to lock it in place.
2.
3. 4.
7. 6. 5.
6-cylinder models
4-cylinder models
Lights
Maint enance291
B BU
UL LBB
T
T A
A B
B

Testthelightstomakesurethe
new bulb is working. Insert the socket back into the
headlight assembly. Turn it
clockwise to lock it in place. Install the new bulb in the socket.
Turn it clockwise to lock it in place. Remove the burned out bulb f rom
thesocketbypushingitinand
turning the bulb counterclockwise
until it unlocks.
Remove the socket from the
headlight assembly by turning it
one-quarter turn counterclockwise.
If you are changing the bulb on
the driver’s side, start the engine,
turn the steering wheel all the way
to the right, and turn off the
engine. If you are changing the
bulb on the passenger’s side, turn
the steering wheel to the left.
Use a f lat-tipped screwdriver to
remove the holding clip f rom the
inner f ender.
Pull the inner f ender cover away
f rom the f ender and bumper.
Put the inner f ender cover in place.
Install the holding clip. Lock it in
place by pushing on the center.
1.
3. 2.
4.5.
6.
7.
8.
9.
Replacing Front Turn Signal and
Side Marker L ight Bulbs
Lights
Maint enance292
H H
O
OL LDD I
INNG G C
CLLIIPP

Pull the bulb straight out of its
socket.
Push the new bulb straight into
the socket until it bottoms.
Open the hood. The f ront parking
light is next to the headlight bulb. Insert the socket back into the
headlight assembly. Turn it
clockwise to lock it in place.
Turn on the parking lights to
make sure the new bulb works.
(Passenger’s side)
Reinstall the radiator reserve tank.
(Driver’s side)
If you need to change a bulb on the driver’s side, remove the
radiator reserve tank.
Remove the socket from the
headlight assembly by turning it
one-quarter turn counterclockwise.
(Driver’s side)
Reinstall the power steering f luid
tank.
Reinstall the radiator reserve tank.
If you need to change a bulb on
the passenger’s side, remove the
radiator reserve tank. On the
driver’s side, remove the power
steering f luid tank. 2. 3.
1. 4.
5.
6.
4-cylinder models
6-cylinder models
6-cylinder models 4-cylinder models
Replacing a Parking L ight Bulb
Lights
Maint enance293
P P
O
OW WE ER
R S
STTE
EE
ER
RI INNG G F
FLLUUI IDD T
TA
A N
NK K
H
H O
OL LDD E
ER
R

Open the trunk.
Remove the fastener from the side
of the trunk lining by turning it
counterclockwise with a coin. Pull
the lining back.Determine which of the two bulbs
is burned out: stop/taillight or turn
signal/taillight.Remove the socket by turning it
one-quarter turn counterclockwise.
Pull the bulb straight out of its
socket.
Push the new bulb straight into
the socket until it bottoms.
Reinstall the socket into the light
assembly by turning it clockwise
until it locks.
Testthelightstomakesurethe
new bulb is working.
Reinstall the trunk lining. Make
sure it is installed under the edge
of the trunk seal.
1.
3.
2. 4.
5.
6.
7.
8.
Replacing Rear Bulbs
(in Fenders)
Maint enance
Lights
294
F FA
A S
STTE
EN
NE ER
R