reset HONDA ACCORD COUPE 2007 CL7 / 7.G User Guide

µ´ µ´
If you select an empty slot in the
magazine, the changer will search
f or the next available CD to load and
play.
If there are no CDs in the changer,
the display will f lash, and you will
have to select another mode.
Press the eject button ( ) to
remove the CD. If you eject the CD,
but do not remove it f rom the slot,
the system will automatically reload
the CD af ter 15 seconds and put it in
pause mode. To begin playing, press
the CD/AUX button.
Press the AM/FM button to switch
to the AM/FM radio while a CD is
playing. To play the CD, press the
CD/AUX button.
If a tape is in the optional tape player,
press the CD/AUX button to switch
to the tape while a CD is playing.
Press the CD/AUX button again to
switch back to the CD player. To select the CD changer, press the
CD/AUX button. The disc and track
numbers will be displayed. To select
a dif f erent disc, use the preset 5
(DISC ) side or preset 6 (DISC )
side of the preset bar. To select the
previous disc, press the preset 5
(DISC ), or preset 6 (DISC ) to
select the next disc in sequence.
If you turn the system of f while a CD
is playing, either with the AUDIO
PWR knob or by turning of f the
ignition, the disc will stay in the drive.
When you turn the system back on,
the CD will begin playing where it
left off. An optional six or eight disc CD
changer is available f or your vehicle
f rom your dealer.
This disc changer uses the same
controls used f or the in-dash CD
player or the radio.
Load the desired CDs into the
magazine, and load the magazine
into the changer according to the
instructions that came with the unit.
To Stop Playing a CD Operating the Optional CD
Changer
AM/FM/CD Player
Features
131
——y
y
(#y
y

Û
The ignition switch must be in the
ACCESSORY (I) or the ON (II)
position. Make sure the open side of
thetapeisfacingright,theninsert
thetapemostof thewayintotheslot.
Thesystemwillpullthetapeinthe
rest of the way and begin to play it.
Thetapedirectionindicatorcomes
on to show you which side of the
tape is playing. The indicates the
sideyouinsertedupwardisnow
playing. If you want to play the other
side, press the preset 3 (PLAY/
PROG) side of the preset bar. When
the player reaches the end of the
tape, it will automatically reverse
direction and play the other side.
Optional
To Play a Tape
AM/FM/CD Player
134
TAPE DIRECTION INDICATOR
CD/AUX
BUTTON REPEAT
INDICATOR
AM/FM BUTTON
SEEK/SKIP BAR PRESET BARS
LX models
RPT BUTTON
DOLBY
INDICATOR
AUDIO PWR KNOB
——y
y
(#y
y

Î
µµ
µ
Î
Dolby noise reduction is manuf actured under
license from Dolby Laboratories Licensing
Corporation. ‘‘DOLBY’’ and the double-D symbol are trademarks of Dolby Laboratories
Licensing Corporation.
To switch to the AM/FM radio or
CD player while a tape is playing,
press the AM/FM or CD/AUX
button. To change back to the tape
player, push the CD/AUX button.
To rewind the tape,
push the preset 1 (REW) side of the
preset bar. You will see REW in the
display. To f ast f orward the tape,
push the preset 2 (FF) side of the
preset bar. You will see FF displayed.
Press the preset 1, 2, or 3 side of the
bars to take the system out of rewind
or fast forward. Press the side to f ind
the beginning of the current song or
passage. Press the side to f ind
the beginning of the next song or
passage. When the system reaches
the beginning of a song or passage, it
begins to play it.
Press the RPT button
to continuously play a song or
passage. You will see RPT displayed.
The track will repeat until you press
the RPT button again.
The skip and repeat
f unctions use silent periods on the
tape to find the end of a song or
passage. These f eatures may not
work if there is almost no gap
between selections, a high noise
level, or a silent period in the middle
of a selection.
Dolby noise reduction comes on
when you insert a tape. The
indicator in the display also
comeson.If thetapewasnot
recorded in Dolby, turn it of f by
pressing the preset 4 (NR) side of
the preset bar. Dolby remains of f
until you press the preset bar again.
To remove the tape, press the eject
button on the tape player. If you
want to turn the player off, press the
AUDIO PWR knob or turn of f the
ignition. The tape will remain in the
drive. When you turn the system
back on, the tape will be in pause
mode. Press the preset 3 (PLAY/
PROG) side of the preset bar.
To Stop Playing a Tape
FF/REW
T ape Search Functions SK IP
REPEAT
AM/FM/CD Player
Features
135
NOTE:
——y
y
(#y
y

The band and f requency that the
radio was last tuned to is displayed.
To change bands, press the AM/FM
button. On the FM band, ST will be
displayed if the station is broadcast-
ing in stereo. Stereo reproduction in
AM is not available.
For inf ormation on XM satellite radio,
see page .
The ignition switch must be in the
ACCESSORY (I) or ON (II) position.
Turn the system on by pushing the
AUDIO PWR knob or the AM/FM
button. Adjust the volume by turning
the AUDIO PWR knob.
139
On U.S. EX-L and EX-V6 models
To Play the AM/FM Radio
A M/FM/CD Changer
136
TUNE BAR
SOUND BUTTON
AM/FM BUTTON
STEREO INDICATOR
SEEK BAR
SCAN BUTTON PRESET
BARSA.SEL
BUTTON
NOTE: This illustration shows the U.S. EX-L and EX-V6 models.
Other models are similar. AUDIO PWR KNOB
EX, EX-L, SE, and all V6 models without navigation system
——y
y
(#y

y

µ
µ µµ
µ
µ
You can use any of f ive methods to
f ind radio stations on the selected
band: TUNE, SEEK, SCAN, the
preset bars, and AUTO SELECT.
Use the TUNE bar to tune
the radio to a desired f requency.
Press the side of the bar to tune
to a higher f requency, and press the side to tune to a lower
f requency.
The seek f unction
searches up and down f rom the
current f requency to f ind a station
with a strong signal. To activate it,
press the or side of the
bar, then release it. The scan f unction samples
all the stations with strong signals on
the selected band. To activate it,
press the SCAN button, then release
it. You will see SCAN in the display.
The system will scan f or a station
with a strong signal. When it f inds
one, it will stop and play that station
f or about 5 seconds. If you do
nothing, the system will then scan
f or the next strong station and play it
for 5 seconds. When it plays a station
that you want to listen to, press the
SCAN button again. Each side of the bars
Select the desired band, AM or
FM. FM1 and FM2 let you store
two f requencies with each side of
the preset bar.
function to tune the radio to a
desired station.
Pick a preset number (1 6), you
want for that station. Press the left
or right side of the bar, and hold it
until you hear a beep.
1. 3.
To Select a Station
TUNE SEEK SCA N Preset
A M/FM/CD Changer
Features
137
——y
y
(#y
y
AM and two f requencies on FM. 2.
Usethetune,seek,orscan
(1 6) can store one f requency on

µµ
µ
µ
µ
Repeat steps 1 through 3 to store a
total of six stations on AM and
twelve stations on FM.
The preset f requencies may be lost if
your vehicle’s battery goes dead, is
disconnected, or the radio f use is
removed. If you are
traveling far from home and can no
longer receive your preset stations,
you can use the auto select feature to
find stations in the local area. You will see a ‘‘0’’ displayed af ter
pressing a preset bar if auto select
cannot f ind a strong station f or every
preset bar.
,pressthe
A. SEL (auto select) button. This
restores the presets you originally
set.
Press the A. SEL button. ‘‘A.SEL’’
f lashes in the display, and the system
goes into scan mode f or several
seconds. It stores the f requencies of
six AM, and twelve FM stations in
the preset bars. If you do not like the stations auto
select has stored, you can store
other f requencies on the preset bars
as previously described.
Press the SOUND button repeatedly
to display the bass (BAS), treble
(TRE), f ader (FAD), and balance
(BAL) settings.
The system will return to the audio
display about 5 seconds af ter you
stop adjusting a mode.Adjusts the bass.
Adjusts the balance, or side-
to-side strength of the sound. Adjusts the treble.
Adjusts the fader, or the
f ront-to-back strength of the sound.
Eachmodeisshowninthedisplayas
it changes. Turn the AUDIO PWR
knob to adjust the setting to your
liking. When the level reaches the
center, you will see a ‘‘ ’’ in the
display.
4.
To turn of f auto select
AUTO SELECT
Adjusting the Sound
BAS
BAL
TRE
FAD
A M/FM/CD Changer
138
——y
y
(#y
y

Your vehicle is capable of receiving XM
Satellite Radio anywhere in the
United States except Hawaii and
Alaska. It is not available in Canada. XM
is a registered trademark of
XM Satellite Radio, Inc.
Satellite radio is available on U.S.
models only.
The ignition switch must be in the
ACCESSORY (I) or the ON (II)
position.
Turn the system on by pushing the
AUDIO PWR knob or the CD/AUX/
XM button.
Turn the AUDIO PWR knob to
adjust the volume.
U.S. EX-L and EX-V6 models
A M/FM/CD Changer
To Play XMSatellite Radio
XM
Satellite Radio
Features
139
PRESET BARS
CATEGORY INDICATOR
SEEK/SKIP BAR SCAN BUTTON TUNE BAR
DISP
BUTTON
U.S. EX-L and EX-V6 models
CD/AUX/XM
BUTTON
AUDIO PWR KNOB
——y
y
(#y
y

µµ
µ
µ µ The scan f unction samples
all channels f or 5 seconds. To
activate the function, push the SCAN
button. Push it again to get out of the
sequence.
Each side of the preset
bar can store one channel in XM1
and one in XM2.
Repeat steps 1 through 3 to store a
total of six stations on XM1 and
six on XM2.
The
seek/skip f unction selects the
various categories in XM, such as
Jazz/Blues, Rock, Classical, etc.
Push the to change the
category f orward. Push the to
change the category backward. To
search f or channels within a
category, press the TUNE bar .
Press the TUNE bar to change
channel selections. Press f or
higher numbered channels and
f or lower numbered channels.
When in the satellite radio mode,
you can use any of f our methods to
f ind channels: TUNE, SEEK/SKIP
(CATEGORY), SCAN, and the
preset bars.
Push the CD/AUX/XM button.
(You will see XM1 or XM2.)
Press and release this
button to change the display. The
display changes in this sequence:
channel name, channel number,
category, artist name, and music title. Usethetune,seek,orscan
function to tune the radio to a
desired station.
Pick a preset icon or number, and
hold it until you hear a beep.
1. 2. 3. 4.
T o Select a Channel
SCA N
Preset
SEEK /SK IP (CA T EGORY)
TUNE DISP
A M/FM/CD Changer
140
——y

y
(#y
y

Î
Î
CONT INUED
To load or play CDs, the ignition
switch must be in the ACCESSORY
(I) or the ON(II) position.
On models with Satellite Radio You operate the CD changer with
the same controls used f or the radio.
To select the CD changer, press the
CD/AUX button (CD/AUX/XM
button on models with satellite
radio). The number of the track
playing is shown in the display. With
the in-dash CD changer, the disc and
track numbers are displayed. The
system will continuously play a CD
until you change modes.
You cannot load and play 3-inch
(8-cm)discsinthissystem.
:
To Play a CD
A M/FM/CD Changer
Features
141
CD/AUX
BUTTON
EJECT
BUTTON
SEEK/SKIP
BAR
LOAD BUTTON CD LOAD INDICATORCD SLOT
TRACK NUMBER
AM/FM BUTTON
DISC NUMBER RPT BUTTON
RDM
BUTTON
PRESET
BARS
NOTE: This illustration shows the U.S. EX-L and EX-V6 models.
Other models are similar. CD/AUX/XM
BUTTON
AUDIO PWR KNOB
EX, EX-L, SE, and all V6 models without navigation system
——y
y
(#y
y

µ
µµ ´ µ
µThe scan f unction samples
all the tracks on the selected disc in
the order they are recorded on the
CD. To activate it, press and release
the SCAN button. You will see SCAN
in the display. You will get a 10
second sampling of each track on the
selected CD. Press the SCAN button
again to get out of the system.
You can also load a CD into an empty
position while a CD is playing by
pressing the appropriate side of a
preset bar. The system stops playing
the current CD and starts the
loading sequence. It plays the CD
just loaded.
You operate the CD changer with
the same controls used f or the radio.
The numbers of the disc and track
playingareshowninthedisplay.
To select a dif f erent disc, press the
appropriate side of a preset bar
(1 6) or use the preset 5 (DISC )
to select the previous disc or preset 6
(DISC ) to select the next disc in
sequence. If you select a loaded
position in the CD changer, the
system will try to load the CD in the
next available slot. Each time you
press and release , the system
skips forward to the beginning of the
next track. Press and release to
skip backward to the beginning of
the current track. Press it again to
skip to the beginning of the previous
track.
To move rapidly within a track, press
and hold or . This f unction samples
the first track of each disc in the
order they are loaded in the CD
changer. To activate it, select D-
SCAN by pressing and holding the
SCAN button. You will see D-SCAN
in the display. You will get a 10
second sampling of the f irst track on
each CD. Press the SCAN button
again to get out of D-SCAN.
SCAN
To Change or Select Tracks
SEEK /SK IP
D-SCAN
A M/FM/CD Changer
Features
143
——y
y
(#y
y