clock reset HONDA ACCORD COUPE 2009 8.G Quick Guide

* Check the owner’s manual for additional information and instructions. Inst Panel/TPMS/Cruise/Compass
Cruise Control
Set/Decel button: Sets cruise control (CRUISE
CONTROL indicator lit) if speed is above 25 mph,
or decreases the set speed if cruise control is set.
Res/Accel button: Resumes set speed if the
cruise control was canceled, or increases set
speed if cruise control is set.
Cancel button: Cancels cruise control. It does not
turn off the cruise control system. You can resume
a set speed if the cruise control was canceled. You
can also cancel the cruise control by tapping the
brake pedal.
Setting the Clock
(without Navigation)
1. With the ignition ON (II), press the CLOCK button until you hear a beep.
2. Press and hold the H button (Preset 4) to set the hour.
3. Press and hold the M button (Preset 5) to set the minutes.
4. Press the CLOCK button again.
Note: On vehicles with navigation, the clock is set
automatically by the navigation system. Cruise control master
button:
Turns the cruise
control system on
(CRUISE MAIN indicator
lit) and off. It does not
set the cruise control.
Compass Operation(EX-L, EX-L V6 w/o Navi)Your vehicle is equipped with a self-calibrating
compass system. Overall operation of this
system can be affected when you drive:
• Near power lines or stations
• Across bridges
• Through tunnels
• Over railroad crossings
• Past large vehicles
• Near large objects that can cause a magnetic
disturbance.
It can also be affected by accessories such as
antennas and roof racks that are mounted by
magnets.
Compass Zone Selection
In most areas, there is a variation between
magnetic north and true north. Zone selection
is required so the compass can compensate for
this variation. See the owner’s manual for zone
selection information.
Calibration
At times, the compass may need to be
manually calibrated after exposure to a strong
magnetic field. If the compass seems to be
continuously showing the wrong direction and
is not self-calibrating, or if the compass display
is blinking with the CAL indicator on, follow the
calibration procedure found in the owner’s
manual.
09 AccordCoupe:09 Accord Coupe.qxd 6/16/2008 1:41 PM Page 4

SOUND AdjustmentSound level adjustment is accessed by pressing
the SOUND button. On EX and EX-L models, the
selector knob (non-navigation models) can be
used. For these models, do this:
1. Press and release the MENU button.
2. Turn the selector knob to move to any of these settings:
BASS TREBLE FADER BALANCE SUBW (EX-
L only) SVC CLOCK ADJUST (on 6-CD system, this is
accessed by the MENU button).
3. Press the selector knob to choose the desired setting.
4. Turn the selector knob to adjust the setting up or down.
5. Press MENU to return to the original display.
Using the Remote Audio Controls
VOL buttons: Adjusts the
volume.
MODE button: Changes
the system to the next
mode: AM/FM1/FM2/CD/
XM1/XM2.
CH buttons
Radio: • Press and release to change to the next or previous preset station.
• Press and hold until you hear a beep. The next station (+ or -) is selected.
CD: Skips to the beginning of the next track or
the start of the current track.
* Check the owner’s manual for additional information and instructions.
(EX, EX-L display shown)
Audio DisplayAudio information is shown in the center display.
Note: With headlights on, the instrument panel
brightness control knob can be used to adjust
audio illumination.
Selector Knob/Interface Dial (if equipped)
Most audio system functions can be controlled by
standard controls. You can access some audio
and navigation functions by using the selector
knob/interface dial on the audio system. Press
ENTER to select an item.
Interface Dial (models with Navigation)
The dial consists of:
• KNOB: Turns left and right to scroll through the display items and adjust the levels.
• SELECTOR (ENTER): Use to select items.
(Navigation display shown)
Selector KnobInterface Dial
Enter
Knob
Selector
09 Accord Coupe 13ab:ExtraPages.qxd 6/16/2008 1:43 PM Page a13