bulb HONDA ACCORD SEDAN 2001 Owner's Manual (in English)

Indicator Lights

Traction Control System(TCS) Indicator

On all V6 models

This indicator has three functions:
1. It comes on as a reminder that you have turned off the Traction
Control System.
2. It flashes when the TCS is regulating wheelspin.
3. If it comes on and stays on when the Traction Control System is on,it indicates that there is a problem
in the TCS.
This light also comes on when you turn the ignition ON (II) and goes offafter the engine starts. See page
206 for more information on the

TCS.
Door and Brake Lamp Monitor
The appropriate light comes on in this display if the trunk or any dooris not closed tightly. If a brake light does not work, the BRAKE LAMP
indicator comes on when you push
the brake pedal with the ignition switch ON (II).
A burned out brake light is a hazard when drivers behind you cannot tell
you are braking. Have your brakelights repaired right away.
All the lights in the monitor display
come on for a few seconds when you
turn the ignition switch ON (II). Turn Signal and
Hazard WarningIndicators
The left or right turn signal light blinks when you signal a lane changeor turn. If the light does not blink or
blinks rapidly, it usually means oneof the turn signal bulbs is burned out (see page 277 ). Replace the bulb as
soon as possible, since other drivers
cannot see that you are signalling.
When you turn on the Hazard
Warning switch, both turn signal lights blink. All turn signals on the
outside of the car should flash.
Instruments and Controls

TCS

Maintenance

This section explains why it is important to keep your car well
maintained and to follow basic
maintenance safety precautions.
This section also includes Maintenance Schedules for normaldriving and severe driving conditions,
a Maintenance Record, and instruc-
tions for simple maintenance tasks
you may want to take care of
yourself.
If you have the skills and tools to per-
form more complex maintenance
tasks on your Honda, you may want
to purchase the Service Manual. See page 345 for information on how toobtain a copy, or see your Honda

dealer.
Maintenance Safety....................... 220

Important Safety Precautions ..221

Maintenance Schedule.................. 222

Maintenance Record..................... 229
Owner Maintenance Checks........ 231

Fluid Locations............................... 232

Engine Oil....................................... 234
Adding Oil................................... 234Recommended Oil..................... 235
Synthetic Oil............................... 235

Additives..................................... 235
Changing the Oil and Filter...... 236

Cooling System.............................. 239
Adding Engine Coolant............. 239Replacing Engine Coolant........ 241

Windshield Washers..................... 246

Transmission Fluid........................ 247
Automatic
Transmission.......................... 247

5-speed Manual
Transmission.......................... 249

Brake and Clutch Fluid................. 251
Brake System............................. 251
Clutch System............................ 252

Power Steering............................... 252

Air Cleaner Element...................... 253
Hood Latch..................................... 256

Spark Plugs..................................... 256

Replacement............................... 256

Specifications............................. 257

Battery............................................ 260

Wiper Blades.................................. 263
Air Conditioning System............... 265
Air Conditioning Filter.................. 266 Drive Belts...................................... 266
Timing Belt..................................... 267
Tires................................................ 267
Inflation...................................... 268

Inspection................................... 270
Maintenance............................... 270
Tire Rotation.............................. 271 Replacing Tires and Wheels .... 271
Wheels and Tires....................... 272 Winter Driving........................... 273
Snow Tires.............................. 273

Tire Chains............................. 273
Lights.............................................. 274 Replacing Bulbs......................... 276
Storing Your Car............................ 285
Maintenance

Lights

Check the operation of your car's
exterior lights at least once a month.
A burned out bulb can create an unsafe condition by reducing yourcar's visibility and the ability tosignal your intentions to other
drivers.
HEADLIGHT
TURN SIGNAL/SIDE MARKER LIGHT
PARKING LIGHT
Maintenance

Lights

HIGH-MOUNT BRAKE LIGHT

BACK-UP LIGHT

STOP/TAILLIGHT

TURN SIGNAL LIGHT

TAILLIGHT
Check the following:
Headlights (low and high beam)
Parking lights
Taillights Brake lightsHigh-mount brake light
Turn signals Back-up lights
Hazard light functionLicense plate light
Side marker lights
Daytime running lights (Canadian models)
If you find any bulbs are burned out,
replace them as soon as possible.
Refer to the chart on page 327 to determine what type of replacement
bulb is needed.
Maintenance

Lights

Headlight Aiming

The headlights were properly aimed when your car was new. If youregularly carry heavy items in the
trunk, readjustment may be required.
Adjustment of the headlights should be performed by a Honda technicianor other qualified mechanic.
Replacing a Headlight Bulb
Your car has two bulbs on each side, four in total. Make sure you arereplacing the bulb that is burned out.
Your car uses halogen headlight bulbs. When replacing a bulb, handleit by its plastic case and protect the
glass from contact with your skin or
hard objects. If you touch the glass,clean it with denatured alcohol and a
clean cloth.
BULB

1. Open the hood. If you need to change a bulb on
the passenger's side (on the driver's side on 6-cylinder models),
remove the radiator reserve tank.
2. Remove the electrical connector from the bulb by squeezing theconnector to unlock the tab, thenslide the connector off the bulb. 3. Remove the bulb by turning it
approximately one-quarter turn
counterclockwise.
4. Insert the new bulb into the hole and turn it one-quarter turn clock-
wise to lock it in place.
5. Push the electrical connector back onto the bulb. Make sure it is on
all the way.
6. Turn on the headlights to test the new bulb.
7. (Passenger's side on 4-cylinder models, driver's side on 6-cylindermodels)
Reinstall the radiator reserve tank.

Halogen headlight bulbs get very hot when lit. Oil, perspiration, or a scratch
on the glass can cause the bulb to
overheat and shatter.

Maintenance
NOTICE

TAB

Lights

Replacing Front Turn Signal and Side Marker Light Bulbs
HOLDING CLIP
1. If you are changing the bulb on the driver's side, start the engine,
turn the steering wheel all the wayto the right, and turn off the
engine. If you are changing the
bulb on the passenger's side, turn the steering wheel to the left. 2. Use a flat-tipped screwdriver to
remove the holding clip from the
inner fender.
3. Pull the inner fender cover away from the fender and bumper.
4. Remove the socket from the headlight assembly by turning itone-quarter turn counterclockwise. 5. Remove the burned out bulb from
the socket by pushing it in and
turning counterclockwise until it

unlocks.

6. Install the new bulb in the socket. Turn it clockwise to lock it in place.
7. Insert the socket back into the headlight assembly. Turn itclockwise to lock it in place.
8. Test the lights to make sure the new bulb is working.
9. Put the inner fender cover in place. Install the holding clip. Lock it in
place by pushing on the center.

Maintenance

Lights

Replacing a Parking Light Bulb
1. The parking light bulb is under the headlight bulb.
Turn the bulb holder one-quarter turn counterclockwise to remove it
from the lens.
2. Pull the bulb straight out of its
socket.

Push the new bulb straight into
the socket until it bottoms. 3. Put the bulb holder back into its
hole in the lens, and turn it
clockwise until it locks.
4. Turn on the parking lights to make sure the new bulb works.

Maintenance

Lights

Replacing Rear Bulbs (in Fenders)
1. Open the trunk. Remove the fastener from the side
of the trunk lining by turning it
counterclockwise with a coin. Pull
the lining back. 2. Determine which of the two bulbs
is burned out: stop/taillight or turn
signal.

3. Remove the socket by turning it one-quarter turn counterclockwise. 4. Pull the bulb straight out of its

socket.

Push the new bulb straight into
the socket until it bottoms.
5. Reinstall the socket into the light assembly by turning it clockwise
until it locks.
6. Test the lights to make sure the new bulb is working.
7. Reinstall the trunk lining. Make sure it is installed under the edge
of the trunk seal.
8. Put the fastener in the hole on the side of the trunk lining and push
on the center until it locks (the
center is flush with the head).
Maintenance

FASTENER

Lights

Replacing Rear Bulbs

(in Trunk Lid)
1. Open the trunk.
2. Determine which of the two bulbs is burned out: taillight or back-up
light.
3. Remove the socket by turning it
one-quarter turn counterclockwise.
4. Remove the burned out bulb from the socket by pulling it straight outof its socket. 5. Install the new bulb in the socket.
6. Reinstall the socket into the light

assembly.

7. Test the lights to make sure the new bulb is working.
Maintenance

Lights

Replacing a High-mount Brake
Light Bulb
1. Open the trunk and remove the socket from the light assembly by
turning it one-quarter turn counter-
clockwise.

2. Remove the burned-out bulb by pulling it straight out of the socket.
3. Install the new bulb and reinstall the socket. Make sure the new
bulb is working. Replacing a Rear License Bulb
1. Remove the license light assembly by carefully prying on the leftedge of the lens with a flat-tipscrewdriver and pulling the
assembly out. 2. Remove the lens from the bulb
holder by pulling the lens whilesqueezing the tabs on both sides
of the holder.

CONTINUED

Maintenance

BULB