Can HONDA CIVIC 1996 6.G Workshop Manual

Power Windows (contd)
- How the Circuit Works
CAUTION: You could iniure your arms, hands, or
fingers if you unintentionally switch the driver's
window to "automatic down" while working in
that door with the power on. Disconnect the
window switch conneclot or the battery when
working in the driver's door.
System Description
The operation of the power windows is controlled by
the main switch in the power window master switch.
When the main switch is in OFF, only the driver's door
window can be opened or closed. With the main
switch ON, all windows can be ooened or closed
either by swtches in the master panel, or swttches in
the doors. The driver's window switch also has an
automatic down mode which is tumed on by pushing
the switch down to its second oosition.
The power windows are driven by reversible motors.
Each motor is protect€d by a built-in circuit breaker.
lf the window switch is held on too long (with the
window obstructed, or after the window is fully up or
down), the circuit breaker opens the circuit. The
circuit breaker resets automaticallv as it cools.
Driver's Window
With the ignition switch in ON, voltage is provided to
the coil of the power window relay through fus€ 24.
The contacts of the power window relay close, and
voltage is applied to the driver's switch. When you
push the power window master switch to UP, voltage
is applied to the driver's window motor. (The motor's
ground path is back through the master power
window switch.) The driver's window motor then
drives the window up. When you push the switch to
DOWN, voltage is applied in the opposite direction
and the motor drives the window down.
Automatic Down (Driver's Window)
With the ignition switch in ON or START, voltage is
applied to the coil of the power window relay. The
contacts of the power window relay close and
voltage is applied lo the power window master
switch. When you push the driveas switch to the
AUTO DOWN position, voltage is applied through
the driver's switch to the driver's window motor. The
control unit receives pulses at the pulser input while
the motor is running. When the window is fully
down, the motor stops, and pulses are no longer
generated by the pulser. This is sensed by the
control unit at the pulser input, and voltage is no
longer applied to the driver's window motor.
Passenger Windows
With the ignition switch in ON, voltage is applied to
the coil of the power window relay through fuse 24.
The contacts of the power window relay then close,
applying voltage to the individual window switches
and the power window master switch. With the
master panel main switch ON, the passenger
windows can be ooerated from the individual
window switches or from tho master panel switches.
When you push the front passengsr's window
switch to UP, voltage is applied to the f ront
passenger's window motor. (The motor is grounded
through the contacts in the front passenger's
window switch and the oower window master
switch.) The window moves up as long as you hold
the switch in the UP position. lf you push the switch
to DOWN, voltage is applied in th€ opposite
direction to the front passenger's window motor, and
the window movss down as long as you hold the
switch in the DOWN Dosition. The window switches
in the other doors operate similarly.
When you push the front passenger's switch in the
master panel to UP, voltage is applied through the
front passenger's window switch contacts to the
front passengefs window motor. (The motor is
grounded through the contacts in the front
passenger's window switch and the power window
master switch.) The window moves up as long as
you hold the switch in the UP position. lf you push
the switch to DOWN, voltage is applied in the
opposite direction to lhe front passenger's window
motor, and the window moves down as long as you
hold the switch in the DOWN position. The other
passenger window switches in the master panel
operate similarly.
Refer to the Service Manual (Section 23, Electrical)
for specific tests or troubleshooting procedures.
120-4

Power Door Locks (cont'd)
- How the Circuit Works
Keyless Entry System
The keyless door locks combine the power door
locks with a remote keyJob transmitter. The keyless
receiver unit is part of the radio. The keyless
receiver unit receives direct inputs f rom the ignition
key switch, the passenger door switches, and an
indirect input trom the driver's door switch through
the integrated control unit.
Power Door Locks (With or Wlthout Keyless)
The power door lock system is made up of the
oower door lock control unit. driver's door lock
switch, and individual door lock actuators. The
power door locks are controlled by the driver's door
lock switch and the driver's door lock actuator
switch.
Transmitter (With Keyless Entry)
The transmitter sends coded radio wave signals to
the keyless receiver unit when one ot its buttons is
pressed. Each transmitter has a unique code that
must be 'laught" to the keyless receiver unit before
it can operate the door locks or any other lunction.
Up to 4 transmitters can be programmed to operate
the keyless door locks.
Door Locking (With or without Keyless Entry)
When you push the driver's door lock switch to the
lock position, ground is applied to the GBN/IVHT
wire to the oower door lock control unit. The control
unit then applies battery voltage to the WHT/RED
wire and ground to the YEURED wire. The
passenger door lock actuators then activate to lock
the corresponding door locks.
When you lock the driver's door with the key or door
lock knob, it is mechanically locked, and the driver's
door lock actuator switch applies ground to the
oower door lock control unit. The control unit then
applies battery voltage to the WHT/RED wire and
ground to the YEURED wire, activating the
passenger door lock actuators which lock the doors.
Dool Locking with Transmitter
When you press the LOCK button on the remote
transmitter, the power door lock control unit applies
battery voltage to the WHT/RED wire and ground to
the YEURED wire. The passenger door lock
actuators then activate and lock the doors. A ground
slgnal is also applied to the BLU/RED wire to lock
the driver's door. lf any door is open, you cannot lock
it using the remote transmitter.
Door Unlocking (With or Without Keyless Entry)
When you push the driver's power door lock switch
to the unlock position, ground is applied to the
GRN/ORN wire to the power door lock control unit.
The control unit then applies battery voltage to the
YEURED and BLU/RED wires and ground to the
WHT/RED wire. The door lock actuators then
activate to unlock the doors.
When you unlock the driver's door with the key or
the door lock knob, it is mechanically unlocked; the
other doors do not unlock.
Door Unlocking (With Transmltter)
When you press the UNLOCK button on lhe remote
transmitter once. the power door lock control unit
applies battery voltage to the WHT/RED wire and
ground to the BLU/RED wire to unlock the driver's
door. When you press the UNLOCK button twice,
the control unit then applies ground to the YEURED
wires to activate the passenger door locks. lf you do
not open a door within 30 seconds after unlocking
the doors with the transmitter, the doors
automatically relock.
Transmltter Programming
1 . Turn the ignition switch ON (ll).
2. Press and hold the Valet-Disarm button on the
radio (between the AM/FM button and the
CD/TAPE button) to enter the programming
mode. (Continue to hold the button during the
procedure, or programming will be cancelled.)
Check that the power door locks cycle to confirm
that you're in the programming mode.
3. Press the "LOCK' or "UNLOCK' button on the
transmitter. Check that the power door locks
cycle to confirm that the code was accepted.
4. Press the "LOCK" or "UNLOCK" button on each
of the remaining transmitters. (You can program
up to four transmitters per vehicle.)
5. After all the transmitters have been
programmed, release lhe Valet-Disarm button to
exit the programming mode.
Beep On/Oft Feature
'I . Press and hold the LOCK and OPTION buttons
on the transmitter.
2. Watch the transmitter's LED:
One flash: Beeo activated.
Two tlashes: Beeo deactivated.
130-4

Power Door Locks (conrd)
- How the Circuit Works
Keyless Entry System
The keyless door locks combine the power door
locks with a remote key-fob transmitter. The keyless
door lock control unit receives direct inputs from the
ignition key switch, the passenger door switches,
and an indirect inDut from the driver's door switch
through the integrated control unit.
Power Door Locks
The power door lock system rs made up ot the
keyless door lock control unit, driver's door lock
switch, and individual door lock actuators. The
power door locks are controlled by the driver's door
lock switch and the driver's door lock actuator
switch.
Transmittel
The transmitter sends coded radio wave signals to
the keyless door lock conlrol unit when one of its
buttons is pressed. Each transmitter has a unique
code that must be 'laught" to the conlrol unit before
it can operate the door locks or any other function.
Up to 4 transmitters can be programmed to operate
the keyless door locks.
Door Locking
When you push the driveas door lock switch to the
lock position, ground is applied to the GRNMHT
wire to the keyless door lock control unit. The
control unit then applies battery voltage to the
WHT/RED wire and ground to the YEURED wire.
The passenger door lock actuators then activate to
lock the corresponding door locks.
When you lock the dnver's door with the key or door
lock knob, it is mechanically locked, and the driver's
door lock actuator switch applies ground to the
oower door lock control unit. The control unit then
applies battery voltage to the WHT/RED wire and
ground to the YEURED wire, activating the
passenger door lock actuators which lock the doors.
Door Locking with Transmitter
When you press the LOCK button on the remote
transmitter, the keyless door lock control unil applies
battery voltage to the WHT/RED wire and ground to
the YEURED wire. The passenger door lock
actuators then activate and lock the doors. A ground
signal is also applied to the BLU/RED wire to lock
the driver's door. lf any door is open, you cannot lock
it using the remote transmitter.
Door Unlocking
When you push the driver's power door lock switch
to the unlock position, ground is applied to the
GRN/ORN wire to the keyless door lock control unil.
The control unit then applies battery voltage to the
YEUREO and BLU/RED wires and oround to the
WHT/RED wire. The door lock actuators then
activate to unlock the doors.
When you unlock the driver's door with the key or
the door lock knob, it is mechanically unlocked; the
other doors do not unlock.
Door Unlocking with Transmitter
When you press the UNLOCK button on the remote
transmitter once, the keyless door lock control unit
applies battery voltage to the WHT/RED wire and
ground to the BLU/RED wire to unlock the driver's
door. When you press the UNLOCK button twice,
the control unit then applies ground to the YEURED
wires lo activate the passenger door locks. lf you do
not open a door within 30 seconds after unlocking
the doors with the transmitter, the doors
automatically relock.
Transmitter Programming
. Entering the programming mode cancels all
learned transmitter codes, so none of the
previously programmed transmitters will work.
You must reprogram all the transmitters once
you're in the programming mode.
. To keep the system from exiting the
programming mode, complete each step within 5
seconds of the previous step, and program the
transmitters within 10 seconds of each other.'1 . Turn the ignition switch ON (ll).
2. Press the "LOCK" or "UNLOCK" button on one
of the transmitters. (A non-programmed
transmitter can be used for this step.)
3. Turn the ignition switch OFF (0).
4. Repeat steps 1, 2, and 3 two more times with
the transmitter used in step 2.
5. Turn the ignition switch ON (ll).
6. Press the "LOCK" or "UNLOCK" button on the
same transmitter. Check that the power door
locks cycle to confirm that you're in the
programmrng mooe.
7. Press the "LOCK" or "UNLOCK" button on each
lransmitter. (You can program up to four
lransmitters per vehicle.) Check that the power
door locks cycle after you push each transmitter
button, contirming that the system has accepted
the transmitter's code.
Beep On/Off Feature
1 . Press and hold the LOCK and OPTION buttons
on the transmitter.
2. Watch the transmitter's LED:
One flash: BeeD activated.
Two flashes: Beep deactivated.
130-14

Security System
- '96-'98 USA: HX, LX, EX; '96-'98 Canada: EX. Si
UNDER-HOODFUSE/RELAYBOX
t"'1,",*
,";;;i[ftT"fi'
'lffi;?'- 1
Dfstnoulon. fuO wnr I yEL
,-l_""__
UNDER.DASHFUSE/RELAYBOX
@@
.-"*luuu' ",-f
*'^'*'
,..1
f::T;J
I I
-Tl[3,*,,,*-"""
| |
%;1 l
FUSE 3
I I C5s1 !--Jt--JC423 (Not,i!r13 " u".al
_::;=ffi
HORNRELAY
PHA|O 129 (9A nodel)
{'96-97 models 3)
i'"---i[
il il
'98 model'96-97 models
I Horn Baitery tgnition I: control\
lgnition key II i*iiirr inilt eround IL------ -----J
- -l-s-f---- --------tiY
8LU FEo ll BLU aED I
;t,-
fon:*,
vlEw 21
8LU/FED
1
GAN
t'I
HORN
a-. =--
e.r,".o ll
, Ag::l^.aLu neo ll v,rwoo-'gr-u.neo sersarr R,I v,rw DU BLU/BEo See Seat BeltO -( and tgnition Keyeru neo ll Reminders
' + c4is
.,u*i,l( il,?l?.uo
r-{---- sTEERTNG;:E[t-:--.rsrEERrNG *.1
i l-flb'fitg"# i".e"er;;
-
|
ll-Ukevinisnition l I
:r:["_-----r
ilrff,i$t ! ilr,tlp:
lgnltion Ksy I LOCKSwftch I PHoro z1Closed with
c201
vlEw 30
133
J!@i---;""i ".*l
o"n"'o''
]t ____ __ __ _ _ _i__ _ _ _ _ _ I

';;;1; I r1-- --'I UNDE'------J-i i I 11'.1'.11 lSBi'"Driver .r ' HEADIIOriT '::
door !:t { t-- lPHo'o7unlock Unlock Lock | : L j,- -- -Jinpd input lpr,_j : -9lT1u.r^ -
---- Canada ---'------l
POWER DOOR LOCK ;CONTROL UNIT ,
k;i
L______jg:_l=,_______ juj_.r, _r_f 9_.-u:'F":;!-_ --",*tI
i !**""""I
*",*"[T*Fi
i
.",1
o*u*u'
,* -".11 t-J--'-----'-hff I
"ll-_-_il
|semooeriir f,
't
tr
18 f ia-eii,
L______d"t";tlo"n,o"n| """*",|ft"t'i fsEcuRrwLED,, L--J---------J",0. | | -liffi*
,i,Hfil _[l!,ffisHdsh
i ,of.--s L--d,---t--------cl-+-'dl "."""" !-------t - I, t - Drivgr's door Unlock Lock I Light I U
ii -F-o-:y-"1 - -:i"-1i3y. -TTi- - - - - :"ll'i - - ; 13'*" i q._"u_n'r !--1---- ---'l99,trRoL I
: \varst :l;#"b" I; ; $vitch Securiiv Bus Remote Bus Bus i I vttwte ll C422, f inqrt outDut d€,.az LED control data 0 data l , : I P1oTo 58-a- --' s Y---^a---.;f --.;Y---^;Y---:Y - - - - r ;-.tr'---
. ; UNIT
i *t Drtusr's door untock Lock i ugnt it - uavgrs ooor untocx LocK I Lrgn'
: LED control unloc* outpul outrut outpul ' flash- ': ' iontrot I sEcuRlw
--1-"' ---' I coNrRoL' 'i uNlri vatst, I VarEr tl PHQ|AT3: ; s,vitch Securiiy Bus Remote Bus Bus t)vtEwte, f inarr ornout d'de2 LED control data 0 data l :
7-1 e4re4lon
lfil Iffi;*l
[I$'':r*il
: 84 |, 85A 87A 811 |' Bt2 |' 813 |' vtEw68 | ! sae r.teadli
i i'=::t:::ti------r------s------r, -"** i : ! 8yJfu;; I I Vabt S€curity 8us Remot€ Bus Bus I Reieiver ! ; --_ _.._ ll
:i iffi$ input data2 ffiDul
datao datal iunrr !:""'"^l
(cont'd)
133-1

Security System
- '96-'98 USA: HX, LX, EX; '96-'98 Canada: EX, Si (cont'd)
I ooor
| #Iflinput
-----l sEcuRlrY
LT CRN/FED
LT GFN/RED
LT GBN/REO
a
[ "*
LT.FN,BED
i
.l:T,lT_t
i _ _ ;T_-----l Hui.'n*f' ffi i|. :-:?-'IINTEGB]ATED I PHoro 58 ll ,
!Eilf8t+ lffi'il* ! ! :
LE:E,jJ_i*- | I i
c503
c562
vtEvl 42
BLU/BLK EAA-{ i,i-"i
See GroundDislrihJtion,pag€ 1*10.
c401
------Sedan
Inpur
---{ F6,i,",. ooo. i:< "?;",o,"
trllnxswitchI CoNTROL! UNITI PHora 73
JvtEw sB
2
BLU/ALK
6
BLU/ALK
12(Sedan '15)
BLU/BLK
c411PHOIO 60vtEw 60
H
":-f
Or--<
".^ |l- G601
Light
TRUNK LATCHswrTcHClosed withvunK open.
LTGRN/FED
t___:'I______l
Tll """,
l-.'F-l DRtvER.s| 1 I DooR
Ir-Il3)lll8l,*=- ooor open.- PHOfOg6
LTGRN/REO i ; LT GFN/T,FED
*'^l ft?{,,' I iFRONTPASSENGER'S '
DOOR SWICH:Closed with :door open.PHOTO 96HH
LEFTREARDOORSWITCHClosed withdoor open.
rflf5ii' :
lCJEfii:t*,,,'i- .l^^r ^^6^ |
PHOfO 97
133-2

Security System
- '99-'00 USA: HX, LX, EX,
@
DX-V Si; '99-'00 Canada: EX, Si
@@t@
i
-
| ffii:-
- - - -
I i['"",llae' i
-
1 F;
- - - - - - -
F,...
- - -
I i"t]:.:*'
L-i:i--:::.J L-t----------i::=t s:i2 lf c353 8 Y C352 7 t' C4l9 1 v C423 {NotF#r""
",-^:"\P;!i?," ...'*lii:i',," I lft:i:3''.I::,wHr'cuN
I
*nr
l
"..
I
**l -"'"""[q
;Tto"
--^*[ftFi" --f ;ntn" "..f
t*x;,3'' u:;
-"r,"""Iq
--t----
See PowsrDisti brrtion,C4il8
i !,"1{}"' Batiery IEBP*' rsnidon f
! tgnition key vabr \.
L-----t:gg-____ _gs___ggg___-,r
lgdIon KrySwhchGbssd withkey in ignition.
-----J
STEERINGLOCK
1
ELK
c450
o
-^l
I
:':l
BLUAAIHT
See GroundDistribrtion,pag€ l+7.
fl
r: [-
- -;;----.T - - - -
--iC214 BLU/FEo I I BLU
;iP,li: 3o-.o< ffi8i?;g"'fu, I . 1"*.
".u,"?!..,u R8fr.,!3"Iii, ".^l .+i"ili""swtTcH
'l?,ii;'?,-
ffi8lli"?,1".* I Pag€ 14-6.
!---J r
133-4
HORN

a\
i
- ----'canada
;;;;-gr"Srrif,f I @
" *i'[?'29 : r1----1 qNPEE-llqgo
i r-----
: | 3;::,
-=l
i I l[+'ffi !l[?::'*'I I unlock unlock lock I : LJ,----.1
: L-j5----j!g-------':g:-j sf_e_3s-?
' 6l-----r-T-------- 1T ; wHr
lwi:iiz-
i e""e'I o"no"n!
_
o"n-"'! i iff*f{#i!
i t ffil *smi i""'iF'as€i;;, I cnnronr I or
i I Ii-,dIi""rl---]rl
i'uf---rilf------ lsYef.ify,', fillTli-ix11,,i ".u.".,.1 o"no""i *n,",1''",u,i
lEqlJF,:*:;
i, zof----f-------ttit!;k"':'f------T
i ".u".. I o"n,o"u I o"n,""' I i "ro [ "ro,c"n I
i | | | i i*i ! "'oo*
:Il
i I I I
i i ?asee'ead'sht
; zl-----8l---------qf------rJ
*""""
I
i rl-,:f'-,."",rr
-l:'.:=il
.. . :::::'.1.. i-tt'ilr'iiililil [r---l-------------'-------------------- --il'-- -": iii:;i"'" l'"i::"", 3----- ------i J 7 ^ vEw 16
i
"I-----'1------1 i i-T;-'*-'-"*trJnll'fFi"
i I I .."1 i !1.,9,.:'-'![a*:
i
*"
|
*'*'.! *..*"!
i ! lN+;** i*o'o"
i ,, [-----[-----,J i
"-i";f
"-**,-'
i i-ffi;----;;------'"i-l [ib,!".p."- i I;yJ;l*,-I i !33lY"o
i
i -- --
-; ----i*o i
"'""t1'ffi"'r3o-
I
13tr8"?*1
I
+ (cont'd)
\lr
rlr
)
133-5

Security System
- '99-'00 USA: HX, LX, EX, DX-V Si; '99-'00 Canada: EX, Si (cont'd)
LTGFN/REO
13 LT GBN/REDPHOTO 113
?-a@
c41r i
"i:,1'** I
ILr cRNi BED I
T'll------'l
I Bsl I
LT GFN/REO
LT GFN/BED
c401
------Sedan
! i-------T-'lsFs6l'"l: t ! uxr
ll:nJffeffii*4'aw"o'"! L------J-J
L_____":r----__
UNDER.DASHFUSE/RELAYBOX
RIGHTREARDOORSWITCH :Closed with ;dooropen.,
a
*l;;
'
IT GBN/FED
E
FRONTPASSENGER'SDOOR SWITCHClosed withdoor open.
LT ONN/BED
133-6
I-'r| DRIVER'SI q IDooR
Ir-\l3l3ll3T*H door open.- PHO\O 96

How the Circuit Works
Arming the Security System
The security system can be armed:
r By pressing the remote control LOCK button
(if equipped)
. 20 seconds atter closing all doors (C)UDX only)
Arming with the Transmitter
The security system can be armed by removing the
ignition key from the ignition switch, closing all
doors and the trunk, and pressing the LOCK button
on the transmitter. When you arm the system in this
way, the remote control LED comes on, the status
LED flashes once per second, the parking lights
flash once. the doors lock. and the horn sounds
once if the beeo sound mode is on.
Passive Arming (CX and Dx only)
When you turn the ignition to OFF, remove the
ignition key from the ignition switch, and close all
the doors and the trunk; the system will
automatically arm itself 20 seconds after the trunk
or last door is closed. When you arm the system
this way, the status LED tlashes 4 times per second
during the exit delay time, and once per second
after the system is armed; the parking lights will
flash once to confirm that the system is armed.
Triggering the Alarm
Atter you've armed the system, it will trigger the
alarm if any door or the trunldhatch is opened. lf the
battery is disconnected when the system is armed or
in the alarm mode, reconnecting it will immediately
trigger the alarm. When the alarm is triggered, the
following will occur for 30 seconds:
. the horn sounds
o the parking lights flash once per second
. the status LED flashes hvice oer second
. the starter is disabled
After 30 seconds, the alarm will stop and the
system will rearm. Pressing the transmitter
UNLOCK button will disarm the svstem.
tlr
133-13
Disarming the System without the Remote
Transmitter (HX, LX, and EX)
You can disarm the system by turning the ignition
switch to ON (ll) and pressing the disarm/valet
switch on the right side ol the stereo tuner face. The
disarm switch will also disarm the svstem after the
system has been triggered.
Disarming the System with the Remote
Transmitter (Hx, Lx, Ex, DX-V, and Si)
Pressing the transmitter UNLOCK button will disarm
the system. The parking lights llash t\ivice if the
alarm has not been tnggered. The parking lights
flash three times if the alarm has been triggered.
The driver's door will unlock. lf you press the unlock
button twice, it will unlock all doors. lf a door is not
opened within 30 seconds, the system will lock all
doors and rearm.
Disarming the System (CX and DX only)
lf the system arms itself, there is a 20 second delay
after you open a door before the alarm will trigger.
To disarm the system in this mode, simply turn the
ignition switch to the ON position
ldentitying Tripped Sensors
The system identifies which sensor trips the alarm
by flashing the status LED. To display the trip
sensor flash code, press the disarm/valet switch 3
times within 5 seconds after the system has been
disarmed. The status sensor will blink according to
the followino codes:
SensorsNumber of Flashes
Door
TrunldHatch
System Switches
1 blink, pause, repeat
2 blinks, pause, repeat
3 blinks, pause, repeat
For further operating instructions, see the security
syslem owner's manual.
(cont'd)