ECO mode HONDA CIVIC COUPE 2006 8.G User Guide

The auto door locking f eature has
two or three possible settings,
depending on the transmission type
(A/T or M/T):Make sure the shif t lever is in
Park (P), and close the driver’s
door.
Turn the ignition switch to the ON
(II) position.Set the parking brake.
Push and hold the brake pedal,
then move the shift lever out of
Park (P).
Pushandholdthefrontof the
master door lock switch on the
driver’s door. You will hear a
clicking sound, and af ter about 5
seconds, you will hear another
clicking sound.
Release the switch, move the shif t
lever to Park (P), and turn the
ignition switch to the LOCK (0)
position within 5 seconds.
Close the driver’s door.
Turn the ignition switch to the ON
(II) position.
The doors lock when the vehicle
speed reaches 9 mph (15 km/h).
On vehicles with automatic
transmission, the doors lock
whenever you move the shif t lever
out of the Park position.
The auto door locking is
deactivated all the time.
This is the def ault setting when
the vehicle leaves the f actory.
1.
2. 1. 3.
4.
5.
6.
2.
Locks both doors when the vehicle’s
speed reaches about 9 mph (15 km/h).
On vehicles with automatic transmission On vehicles with manual transmission
CONT INUED
Door L ocks
To activate either auto door lockmode:A uto Door L ocking
Inst rument s and Cont rols
79
——y
y
(+yy

Open the driver’s door.
On vehicles with automatic
transmission, make sure the shif t
lever is in Park (P).
Turn the ignition switch to the ON
(II) position.
Set the parking brake.Pushandholdthefrontof the
master door lock switch on the
driver’s door. You will hear a
clicking sound, and af ter about 5
seconds, you will hear another
clicking sound.
Release the switch, and turn the
ignition switch to the LOCK (0)
position within 5 seconds.
The auto door unlocking f eature has
two or three of these possible
settings, depending on the
transmission type (A/T or M/T):
The driver’s door unlocks
whenever you turn the ignition
switch to the LOCK (0) position.
On vehicles with automatic
transmission, the driver’s door
unlocks when you move the shif t
lever to the Park position.
This is the def ault setting when
the vehicle leaves the f actory. The auto door unlocking is
deactivated all the time.
4.
5.
1.
2.
3.
CONT INUED
Door L ocks
To turn the auto door lock modes off:A uto Door Unlocking
Inst rument s and Cont rols
81
——y
y
(+yy

Turn the ignition switch to the ON
(II) position. Make sure the shif t lever is in
Park (P), and close the driver’s
door.Set the parking brake.
Push and hold the brake pedal,
then move the shift lever out of
Park (P).
Pushandholdtherearof the
master door lock switch on the
driver’s door. You will hear a
clicking sound, and af ter about 5
seconds, you will hear another
clicking sound.
Release the switch, move the shif t
lever to Park (P), and turn the
ignition switch to the LOCK (0)
position within 5 seconds.
Close the driver’s door.
Turn the ignition switch to the ON
(II) position.
Pushandholdtherearof the
master door lock switch on the
driver’s door. You will hear a
clicking sound, and af ter about
5
seconds, you will hear another
clicking sound.
Release the switch, and turn the
ignition switch to the LOCK (0)
position within 5 seconds. Set the parking brake.
1.
2. 3.
4.
5.
6.
1.
2.
3.
4.
5.
On vehicles with automatic transmission
Unlocks the driver’s door when the
ignition switch is out of the ON (II)position. On vehicles with manual transmission
Door L ocks
To activate either auto door unlock
mode:
82
——y
y
(+yy

Unlocks driver’s door when the shiftlever is moved to Park (P).On vehicles with automatic transmissiononly
Make sure the shif t lever is in
Park (P), and close the driver’s
door.
Turn the ignition switch to the ON
(II) position.
Set the parking brake. Pushandholdtherearof the
master door lock switch on the
driver’s door. You will hear a
clicking sound, and af ter about 5
seconds, you will hear another
clicking sound.
Release the switch, and turn the
ignition switch to the LOCK (0)
position within 5 seconds.
Open the driver’s door.
On vehicles with automatic
transmission, make sure the shif t
lever is in Park (P).
Turn the ignition switch to the ON
(II) position.
Set the parking brake.
1.
2.
3. 4.
5.
1.
2.
3.
CONT INUED
Door L ocks
To turn the auto door unlock modesoff:
Inst rument s and Cont rols
83
——y
y
(+yy

µ
µ
CONT INUED
The ceiling light (if the ceiling light
switch is in the center position) and
the spotlights (if the switch is in the
Door position on EX and Si models)
will come on when you press the
UNLOCK button. If you do not open
either door within 30 seconds, the
lights f ade out. If you relock the
doors with the remote transmitter
bef ore 30 seconds have elapsed, the
lightsgoesoff immediately.
If you do not open either door within
30 seconds, the doors automatically
relock, and the security system sets
(onU.S.LX,EX,andSimodels).You
cannot unlock it if the key is in the
ignition switch.
Press this button once
to unlock the driver’s door. Push it
twice to unlock the passenger’s door.
Some exterior lights will f lash twice
each time you push the button.
Press this button once to
lock both doors. Some exterior lights
will f lash once. When you push
LOCK twice within 5 seconds, you
will hear a beep to verify that the
doors are locked and that the
security system has set (on U.S. LX,
EX and Si models). You cannot lock
the doors if either door is not f ully
closed or the key is in the ignition
switch.
U.S.:LX,EX,Si
Canada: DX-G, LX, EX, Si
Remote Transmitter
UNL OCK
LOCK
Inst rument s and Cont rols
85
UNLOCK
BUTTON LOCK
BUTTON
TRUNK
RELEASE
BUTTON
PANIC
BUTTON LED
U.S. EX and Si models
UNLOCK
BUTTON LOCK
BUTTON
PANIC
BUTTON LED
U.S.: LX Canada: DX-G, LX, EX, Si
——y
y
(+yy

µ
µ
If it takes several pushes on the
button to lock or unlock the doors,
replace the battery as soon as
possible.
Battery type: CR1616
To replace the battery:Remove the screw at the base of
the transmitter with a small
Phillips-head screwdriver.
Avoid dropping or throwing the
transmitter.
Protect the transmitter from
extreme temperature.
Do not immerse the transmitter in
any liquid.
If you lose a transmitter, the
replacement needs to be
reprogrammed by your dealer.
Press this
button f or about 1 second to open
the trunk. You cannot open the trunk
if the key is in the ignition switch.
Pressthisbuttonfor
about 2 seconds to attract attention:
the horn will sound, and the exterior
lights will f lash f or about 30 seconds.
To cancel panic mode, press any
other button on the remote
transmitter, or turn the ignition
switch to the ON (II) position.
1.
OnU.S.EXandSimodels
Remote Transmitter
Replacing the Transmitter
Battery
T RUNK REL EA SE
PA NICRemote Transmitter Care
86
SCREW
U.S. EX and Si models are shown.
——y
y
(+yy

Af ter both doors are closed tightly,
the light dims slightly, then f ades out
in about 30 seconds.
The ceiling light (with the switch in
the center position) comes on when
you remove the key f rom the ignition
switch. If you do not open a door, the
light stays on, then f ades out in
about 30 seconds.
If you leave either door open without
the key in the ignition switch, the
ceiling light goes of f af ter 3 minutes.
The ceiling light has a three-position
switch; ON, Door Activated, and
OFF. In the Door Activated (center)
position, the light comes on when
you:
Open either door.
Unlock the doors with the key or
the remote transmitter. Turn on a spotlight by pushing the
lens. Push the lens again to turn it
of f . You can use the spotlights at all
times.
On LX model
Interior Lights
Spotlights
Ceiling L ight
106
DOOR ACTIVATED
ON
OFF
——y
y
(+y
y

Your audio system shows a welcome
message on the display when you
turn the ignition switch to the
ACCESSORY (I) or the ON (II)
position. You can see a message
‘‘WELCOME’’ on the display when
your vehicle was new.
You can also customize this welcome
message to your liking with the
audio controls.To change the letter, select the
previous segment by pushing the
bottom of the SEEK button.
Turn the TUNE knob to change a
letter.
Push the top of the SEEK button
to select the next segment, then
turn the TUNE knob to select a
letter. Repeat this procedure to set
your message.
Youcansetuptoabout16
characters on the display.
To select a character:
Make sure the audio system is of f .
PushandholdtheTUNEknob,
then push the power/volume knob
on the audio control panel. You
will see the f irst letter blinking. The system will return to the audio
display about 5 seconds af ter you
stop selecting a letter.
2. 3.
4.
1. To Customize a Message
Audio System (Models without navigation system)
116
EX model is shown. TUNE KNOB
POWER/VOLUME
KNOB
SEEK BUTTON
——y
y
(+y

y

µ
µ µ
The ignition switch must be in the
ACCESSORY (I) or ON (II) position.
Turn the system on by pushing the
power/volume knob or the AM or
FM button (the AM/FM button on
models with XM radio available).
Adjust the volume by turning the
power/volume knob.
The band and f requency that the
radio was last turned to are displayed.
To change bands, press the AM or
FM button (AM/FM button on
models that are XM radio capable).
On the FM band, ST will be
displayed if the station is
broadcasting in stereo. Stereo
reproduction in AM is not available. You can use any of f ive methods to
f ind radio stations on the selected
band: the
preset buttons, and .
Use the TUNE knob to
tune the radio to a desired f requency.
Turn the knob to the right to tune a
higher f requency, and turn it to the
lef t to tune a lower f requency.
The SEEK f unction
searches up and down from the
current f requency to f ind a station
with a strong signal. To activate it,
press the or side of the
SEEK button, then release it. The scan f unction samples
all stations with strong signals on the
selected band. To activate it, press
the SCAN button, then release it.
You will see SCAN in the display.
The system will scan f or a station
with a strong signal. When it f inds
one, it will stop and play that station
f or about 10 seconds.
If you do nothing, the system will
then scan f or the next strong station
and play it f or 10 seconds. When it
plays a station you want to listen to,
press the SCAN button again.
To Select a Station
TUNE,SEEK,SCAN, AUTO SELECT
TUNE
SEEK SCAN
To Play the AM/FM Radio
Audio System (Models without navigation system)
118
——y
y
(+y

y

µµ µ
Each side of the buttons
(1 through 6) can store one
f requency on AM, and two
f requencies on FM.
Select the desired band, AM or
FM. FM1 and FM2 let you store
two f requencies with each side of
the preset button.
Usethetune,seek,orscan
function to tune the radio to a
desired station.
Pick a preset number (1 6), and
hold it until you hear a beep.
Repeat steps 1 through 3 to store a
total of six stations on AM and
twelve stations on FM. If you are
traveling far from home and can no
longer receive your preset stations,
you can use the auto select feature to
find stations in the local area.
Press the A. SEL button. You will see
A. SEL f lashing in the display, and
the system goes into scan mode f or
several seconds. It stores the
f requencies of six AM, and twelve
FM stations in the preset buttons.
You will see a ‘‘0’’ displayed af ter
pressing a preset button if auto
select cannot f ind a strong station f or
every preset button. If you do not like the stations auto
select has stored, you can store
other f requencies on the preset
buttons as previously described.
,pressthe
A. SEL button. This restores the
presets you originally set.
For inf ormation on AM/FM radio
f requencies and reception, see page .
1.
2.
3.
4. 167
To turn of f auto select
Preset
A UT O SEL ECT
Audio System (Models without navigation system)
Features
119
——y
y
(+y
y