ABS HONDA CIVIC HATCHBACK 2003 7.G User Guide

µ
Î ÌÌÌ
Î
Maint enance
160 Service at the indicated distance or time whichever comes first. miles x
1,000
km x 1,000
months
Service the following items at the recommended intervals.
Every 110,000 miles (176,000 km)
Inspect every 110,000 miles (176,000 km), otherwise adjust only if noisy
At 120,000 miles (192,000 km) or 10 years,
then every 60,000 miles (96,000 km) or 5 years Every 3 years (independent of mileage)
See dust and pollen filter on page for replacement information under special driving conditions.
See information on maintenance and emissions warranty, last column, page . Check oil and coolant at each fuel stop
Every 15,000 miles (24,000 km) in dusty conditions, otherwise use normal schedule
Replace every 5,000 miles (8,000 km) or 6 months
Check engine oil and coolant
Replace engine oil
Rotate tires (Check tire inflation and condition at least once per month)
Replace engine oil filter
Inspect front and rear brakes
Lubricate all hinges, locks, and latches
Visually inspect the following items:
Tie rod ends, steering gear box and boots
Suspension components
Driveshaft boots
Check parking brake adjustment
Visually inspect the following items: Brake hoses and lines (including ABS)
All fluid levels and condition of fluidsExhaust system, Fuel lines and connections
Lights and controls, Vehicle underbody
Inspect and adjust drive belts
Replace dust and pollen filter
Replace transmission fluid
Replace air cleaner element
Replace spark plugs
Inspect valve clearance
Inspect idle speed
Replace engine coolant
Replace brake fluid 10 16
203230484064 5080609670
112 80
128 90
144 100160110176120192
Every 160,000 miles (256,000 km) or 8 years 24 48 72
12 36 60
:: 157
190
Maintenance Schedule for Severe Conditions

µµ
Ø Ø Ø ØØØØØØØØØØ Ø ØØØØØØ
ÌÌ
Î
Î Ì
CONT INUED
Maint enance 161
U.S. Owners
Canadian Owners
A, B, C, D, E
AB C D E
Refer to page to determine which schedule to use.
Use the Maintenance Schedule for Severe Conditions.
Service at the indicated distance or time, whichever comes first. Do the items in as required for each distance/time.
5,000 mi/8,000 km/6 mos
10,000 mi/16,000 km/1 yr
15,000 mi/24,000 km
15,000 mi/24,000 km/1-½yrs
20,000 mi/32,000 km/1 yr
25,000 mi/40,000 km/2 yrs
30,000 mi/48,000 km
30,000 mi/48,000 km/2 yrs
35,000 mi/56,000 km/2-½yrs
40,000 mi/64,000 km/2 yrs
45,000 mi/72,000 km
45,000 mi/72,000 km/3 yrs
3yrs
50,000 mi/80,000 km/3 yrs
55,000 mi/88,000 km/3-½yrs
60,000 mi/96,000 km
60,000 mi/96,000 km/3 yrs
65,000 mi/104,000 km/4 yrs
70,000 mi/112,000 km/4 yrs
75,000 mi/120,000 km
75,000 mi/120,000 km/4-½yrs
80,000 mi/128,000 km/4 yrs
85,000 mi/136,000 km/5 yrs
90,000 mi/144,000 km
90,000 mi/144,000 km/5 yrs
95,000 mi/152,000 km/5-½yrs
100,000 mi/160,000 km/5 yrs
105,000 mi/168,000 km
105,000 mi/168,000 km/6 yrs Do item in A.
Do items in A, B.
Do item in E.
Do item in A.
DoitemsinA,B,C.
Do item in A.
Do item in E.
DoitemsinA,B,D.
Do item in A.
DoitemsinA,B,C.
Do item in E.
Do item in A.
Replace brake fluid (independent of mileage).
Do items in A, B.
Do item in A.
Do item in E.
Replace transmission fluid.
DoitemsinA,B,C,D.
Do item in A.
Do items in A, B.
Do item in E.
Do item in A.
DoitemsinA,B,C.
Do item in A.
Do item in E.
DoitemsinA,B,D.
Do item in A.
Do item in A, B, C.
Do item in E.
Do item in A. Replace engine oil.
Replace engine oil filter.
Inspect front and rear brakes.
Rotate tires (follow pattern on page 196 ).
Lubricate all hinges, locks, and latches.
Inspect tie rod ends, steering gear box and boots.
Inspect suspension components.
Inspect driveshaft boots.
Check parking brake adjustment.
Inspect brake hoses and lines (including ABS).
Check all fluid levels, condition of fluids, and check
for leaks.
Inspect exhaust system.
Inspect fuel lines and connections.
Check all lights.
Inspect the underbody.
Inspect and adjust drive belts.
Replace dust and pollen filter .
Replace air cleaner element every 15,000 mi/
24,000 km (independent of time) under dusty
conditions, otherwise use Normal Conditions
schedule.
156
Check engine oil and coolant at each fuel stop.
Check and adjust valve clearance, cold engine, only if noisy.See information on maintenance and emissions warranty, last
column, page .
See dust and pollen filter on page for replacement information
under special driving conditions.
157
NOTE: : :
190
Maintenance Schedule for Severe Conditions (listed by distance/time)

Remove the blade f rom its holder
by grasping the tabbed end of the
blade. Pull f irmly until the tabs
come out of the holder.Examine the new wiper blades. If
they have no plastic or metal rein-
f orcement along the back edge,
remove the metal reinf orcement
strips f rom the old wiper blade and
install them in the slots along the
edge of the new blade.Slide the new wiper blade into the
holder until the tabs lock.
Slide the wiper blade assembly
onto the wiper arm. Make sure it
locks in place.
Lower the wiper arm down against
the windshield.
Lower the passenger’s side f irst,
then the driver’s side.
3. 4. 5. 6. 7.
CONT INUED
Maint enance
Wiper Blades
187
BLADE
BLADE
REINFORCEMENT

Reinstall the dust and pollen f ilter
cover.
Remove the f irst f ilter by pulling it
straight out of the air conditioning
unit. Remove the second f ilter by
sliding it to the lef t, then pulling it
out.
Install the dust and pollen f ilters
into the air conditioning unit.
Make sure the ‘‘AIR FLOW’’
arrows on the f ilter point
downward. Pivot the glove box up into
position. Install the tabs back in
place.
Close the glove box.
If you are not sure how to replace
the dust and pollen f ilters, have them
replaced by your Honda dealer.
5. 6. 7.
3. 4.
Dust and Pollen Filt er
Maint enance 191
DUST AND POLLEN FILTERS

´
Wheels:
Tires:
See page f or inf ormation about
DOT Tire Quality Grading. Tires that are marked ‘‘M S’’ or
‘‘All Season’’ on the sidewall have an
all-weather tread design. They
should be suitable f or most winter
driving conditions. Tires without
these markings are designed f or
optimum traction in dry conditions.
They may not provide adequate
perf ormance in winter driving.
For the best perf ormance in snowy
or icy conditions, you should install
snow tires or tire chains. They may
be required by local laws under
certain conditions.
TheABSworksbycomparingthe
speed of the wheels. When replacing
tires, use the same size originally
supplied with the car. Tire size and
construction can af f ect wheel speed
and may cause the system to work
inconsistently.
If you ever need to replace a wheel,
make sure the wheel’s specif ications
match those of the original wheel
that came on your car. Replacement
wheels are available at your Honda
dealer.
252
Wheels and Tires Winter Driving
Tires
Maint enance
198 15x6J
195/60R15 88V

Remove the rubber weather seal
by pulling on the tab.
Insert the new bulb into the hole,
making sure the tabs are in their
slots. Pivot the hold-down wire
back in place and clip the end into
the slot.
Install the rubber seal over the
back of the headlight assembly.
Make sure it is right side up; it is
marked ‘‘TOP.’’
Push the electrical connector onto
the tabs of the new bulb. Make
sure it locks in place.
Turn on the headlights to test the
new bulb.Use a f lat-tipped screwdriver to
remove the holding clip f rom the
inner f ender.
Pull the inner f ender cover back.
Unclip the hold-down wire f rom its
slot by pushing it in and up. Pivot
it out of the way and remove thebulb.
If you are changing the bulb on
the driver’s side, start the engine,
turn the steering wheel all the way
to the right, and turn off the
engine. If you are changing the
bulb on the passenger’s side, turn
the steering wheel to the left.
3. 4. 5. 6. 7. 1.
3.
2.
CONT INUED
Replacing a Front T urn Signal Bulb
Lights
Maint enance
203
HOLDING CLIP

Open the hatch.Put your fingers between the
interior trim and the hatch glass
on either side of the high-mount
brake light. Caref ully pull down on
the trim to unsnap the clips f rom
the hatch. Work your way toward
each end of the trim. Remove the
trim.Remove the bulb holder f rom the
light assembly by pushing the tabs
on both sides and pulling the bulb
holder down.
Pull the bulb straight out of its
bulb holder. Push the new bulb in
until it bottoms in the bulb holder.
1.
3.
2.
4.
CONT INUED
Replacing the High-mount Brake
Light Bulb
Lights
Maint enance207
BULB HOLDER

Slide the lens to the right until the
lef t side of the lens pops out of the
body. Pull out the light assembly.Remove the lens f rom the socket
by pulling the lens while squeezing
the tabs on both sides of the
socket.
Pull the bulb straight out of its
socket. Push the new bulb in until
it bottoms in the socket.Put the lens back on the bulb
holder and push it until it latches.
Slide the right side of the light
assembly into the hole. Push on
theleftsidetolatchtheassembly
into place.
Turn on the parking lights and
check that the new bulb is
working.
1. 3.
2. 6.
4. 5.
Replacing a Rear License Plate Bulb
Maint enance
Lights
209
BULB
SOCKET

The ceiling lights and spotlights
come apart the same way, but they
do not use the same type of bulbs.Center ceiling light:Pry on the side edge of the lens in
the middle.
Removethelensbycarefully
prying on the edge of the lens with
a f ingernail f ile or a small f lat-tip
screwdriver. Do not pry on the
edge of the housing around the
lens.
Remove the bulb by pulling it
straight out of its metal tabs.
Push the new bulb into the metal
tabs. Snap the lens back in place.
Front ceiling light/spotlights:
Pry on the f ront edge of the lens in
the middle.
1.
2. 3.
Replacing Ceiling and Spotlight Bulbs
Lights
Maint enance
210 FRONT CEILING LIGHT/SPOTLIGHTS CENTER CEILING LIGHT
SOCKET
BULB
BULB

Remove the wrench. Reinstall the
round plug.
To remove the round plug in the
center of the headliner, turn the
plug by using a screwdriver or
coin, then pry it out. Make sure to
align the tabs on the round plug to
the notches on the ceilling as
shown in the illustration.
If the electric motor will not close
the moonroof , do the f ollowing:
Check the f use f or the moonroof
motor (see page ). If the f use
is blown, replace it with one of the
same or lower rating.
Try closing the moonroof . If the
new f use blows immediately or the
moonroof motor still does not
operate, you can close the
moonroof manually.
Get the moonroof wrench out of
the tool kit in the cargo area. Insert the moonroof wrench into
the socket behind this plug. Turn
the wrench until the moonroof is
f ully closed.
1.
2. 3. 4.
5. 6.
240
Closing t he Moonroof
T aking Care of t he Unexpect ed
239
Front
ROUND PLUG
SOCKET