engine oil HONDA CR-V 2005 RD4-RD7 / 2.G User Guide

Honda Motor Oil is the pref erred
5W-20 lubricant f or your vehicle. It is
highly recommended that you use
Honda Motor Oil in your vehicle f or
optimum engine protection. Make
sure the API Certif ication Seal says
‘‘For Gasoline Engines.’’
The oil viscosity or weight is
provided on the container’s label.
5W-20 oil is f ormulated f or year-
round protection of your vehicle to
improve cold weather starting and
f uel economy.
Unscrew and remove the engine oil
fill cap on top of the valve cover.
Pour in the oil slowly and caref ully so
you do not spill any. Clean up any
spills immediately. Spilled oil could
damage components in the engine
compartment.
Reinstall the engine oil f ill cap, and
tighten it securely. Wait a f ew
minutes, and recheck the oil level on
the engine oil dipstick. Do not f ill
above the upper mark; you could
damage the engine.
Oil is a major contributor to your
engine’s perf ormance and longevity.
Always use a premium-grade 5W-20
detergent oil displaying the API
Certif ication Seal. This seal indicates
the oil is energy conserving, and that
it meets the American Petroleum
Institute’s latest requirements.
A dding Engine Oil
A dding Engine Oil
Recommended Engine Oil
Maint enance
193
ENGINE OIL FILL CAP
API CERTIFICATION SEAL
Ambient Temperature

Your vehicle does not require any oil
additives. Additives may adversely
af f ect the engine or transmission
perf ormance and durability.
Always change the oil and f ilter
according to the recommendations in
the maintenance schedule. The oil
and f ilter collect contaminants that
can damage your engine if they are
not removed regularly.
Changing the oil and f ilter requires
special tools and access f rom
underneath the vehicle. The vehicle
should be raised on a service station-
type hydraulic lif t f or this service.
Unless you have the knowledge and
proper equipment, you should have
this maintenance done by a skilled
mechanic.
Run the engine until it reaches
normal operating temperature,
then shut it off.
Open the hood, and remove the
engine oil f ill cap. Remove the oil
drain bolt and washer f rom the
bottom of the engine. Drain the oil
into an appropriate container.
You may use a synthetic motor oil if
it meets the same requirements
given f or a conventional motor oil, it
displays the API Certif ication Seal
and it is the proper weight. You must
f ollow the oil and f ilter change
intervals given in the maintenance
schedule.
1.
2.
A dding Engine Oil, Changing the Oil and Filter
Synthetic Oil
Engine Oil A dditives
Changing the Oil and Filter
194
WASHER
OIL DRAIN BOLT

Refill the engine with the recom-
mended oil.
Engine oil change capacity
(including f ilter):
Replace the engine oil f ill cap.
Start the engine. The oil pressure
indicator should go out within 5
seconds. If it does not, turn of f the
engine, and check your work.
Let the engine run f or several
minutes, then check the drain bolt
and oil f ilter f or leaks.
Turn of f the engine and let it sit
f or several minutes, then check
the oil level on the dipstick. If
necessary, add more oil.
Remove the oil f ilter, and let the
remaining oil drain. A special
wrench (available from your
dealer) is required.
Put a new washer on the drain bolt,
then reinstall the drain bolt.
Tighten the drain bolt to:
Install a new oil f ilter according to
the instructions that come with it.
Check the oil f ilter to make sure
its gasket did not stick to the
engine block. A stuck gasket could
cause an oil leak.
4.
3.
5.
6.
7.
8.
9.
10.
Changing the Oil and Filter
Maint enance
195
OIL FILTER
33 lbf·ft (44 N·m , 4.5 kgf·m)
4.4 US qt (4.2)
Improper disposal of engine oil can be
harmf ul to the environment. If you
change your own oil, please dispose of
the used oil properly. Put it in a sealed
container and take it to a recycling
center. Do not discard it in a trash bin
or dump it on the ground.

Check the f luid level with the
transmission at normal operating
temperature and the vehicle sitting
on level ground. Remove the
transmission f iller bolt and caref ully
f eel inside the bolt hole with your
f inger. The f luid level should be up
to the edge of the bolt hole. If it is
not, add Honda Manual
Transmission Fluid (MTF) until it
starts to run out of the hole.
Put a new washer on the f iller bolt,
then reinstall the f iller bolt and
tighten it securely.
If Honda MTF is not available, you
may use an SAE 10W-30 or 10W-40
viscosity motor oil with the API
Certif ication seal that says ‘‘FOR
GASOLINE ENGINES’’ as a
temporary replacement. However,
motor oil does not contain the proper
additives, and continued use can
cause stiffer shifting. Replace as
soon as it is convenient.
The transmission should be drained
and ref illed with new f luid according
to the time and distance
recommendations in the
maintenance schedule.
Insert the dipstick all the way back
into the transmission securely as
shown in the illustration.
If you are not sure how to add f luid,
contact your dealer.
The transmission should be drained
and ref illed with new f luid according
to the time and distance recommen-
dations in the maintenance schedule.
If you are not sure how to check and
add f luid, contact your dealer.
6.
T ransmission Fluid
Manual Transmission Fluid
200
WASHER FILLER BOLT
Correct level

Fill the f uel tank.
Change the engine oil and f ilter.
Wash and dry the exterior
completely.
Cleantheinterior.Makesurethe
carpeting, floor mats, etc., are
completely dry.Block the rear wheels.
If the vehicle is to be stored f or a
longer period, it should be
supported on jackstands so the
tires are of f the ground.
Cover the vehicle with a
‘‘breathable’’ cover, one made
f rom a porous material such as
cotton. Non-porous materials, such
as plastic sheeting, trap moisture,
which can damage the paint.
If you need to park your vehicle f or
an extended period (more than 1
month), there are several things you
should do to prepare it f or storage.
Proper preparation helps prevent
deterioration and makes it easier to
get your vehicle back on the road. If
possible, store your vehicle indoors. Leave one window open slightly (if
the vehicle is being stored
indoors).
Disconnect the battery.
Support the f ront and rear wiper
blade arms with a f olded towel or
ragsotheydonottouchthe
windshield.
To minimize sticking, apply a
silicone spray lubricant to all door
and tailgate seals. Also, apply a
vehiclebodywaxtothepainted
surfaces that mate with the door
and tailgate seals.If possible, periodically run the
engine until it reaches f ull
operating temperature (the
cooling f ans cycle on and of f
twice). Pref erably, do this once a
month.
If you store your vehicle f or 1 year or
longer, have your dealer perf orm the
inspections called f or in the 2 years/
30,000 miles (48,000 km)
maintenance schedule (Normal
Conditions) as soon as you take it
out of storage (see page ). The
replacements called f or in the
maintenance schedule are not
needed unless the vehicle has
actually reached that time or mileage.
Leave the parking brake off. Put
the transmission in reverse
(manual) or Park (automatic).
187
Vehicle Storage
218

This section covers the more
common problems that motorists
experience with their vehicles. It
gives you inf ormation about how to
safely evaluate the problem and what
to do to correct it. If the problem has
stranded you on the side of the road,
you may be able to get going again.
If not, you will also f ind instructions
on getting your vehicle towed.....................
Changing a Flat Tire .220
.............
If the Engine Won’t Start . 227
................................
Jump Starting .229
..............
If the Engine Overheats . 231
.........
Low Oil Pressure Indicator . 233
..........
Charging System Indicator . 233
.......
Malf unction Indicator Lamp . 234
...............
Brake System Indicator . 235
..................
Closing the Moonroof . 236
..............................................
Fuses .237
..............................
Fuse Locations .240
......................
Emergency Towing .242
Taking Care of the Unexpected
T aking Care of t he Unexpect ed
219

Let the vehicle sit f or a minute.
Open the hood, and check the oil
level (see page ). An engine
very low on oil can lose pressure
during cornering and other driving
maneuvers.
If necessary, add oil to bring the
level back to the full mark on the
dipstick (see page ).If the charging system
indicator comes on brightly
when the engine is running, the
battery is not being charged.
Immediately turn of f all electrical
accessories. Try not to use other
electrically operated controls such as
the power windows. Keep the engine
running; starting the engine will
discharge the battery rapidly.
Go to a service station or garage
where you can get technical
assistance.
Saf ely pull of f the road, and shut
of f the engine. Turn on the hazard
warning lights.
This indicator should never
come on when the engine is
running. If it starts f lashing or stays
on, the oil pressure has dropped very
low or lost pressure. Serious engine
damage is possible, and you should
take immediate action.
Start the engine, and watch the oil
pressure indicator. If it does not go
out within10seconds, turn of f the
engine. There is a mechanical
problem that needs to be repaired
bef ore you can continue driving
(see on page
).
1.
2.
4. 3.
145
193
242
L ow Oil Pressure Indicator
Charging System Indicator
Emergency T owing
L ow Oil Pressure Indicator, Charging System Indicator
T aking Care of t he Unexpect ed
233
Running the engine with low oil
pressure can cause serious mechanical
damage almost immediately. Turn of f
the engine as soon as you can saf ely get
the vehicle stopped.

µµ
Î
Î
No. No. Circuits Protected Amps. Circuits Protected Amps.
No. Amps. Circuits Protected
: On Canadian models
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
Option
Lef t Headlight
Door Lock
Right Headlight
ABS F/S
Battery
Ignition 1
Spare Fuses
20 A
30 A
15 A
20 A
15 A
15 A
15 A
15 A
10 A
30 A
20 A
40 A
40 A
Condenser Fan
Engine
Interior Light
Cooling Fan
Hazard
Small Light
Horn, Stop
DBW
Back Up
ABS Motor
Rear Defroster
Heater Motor
Power Window
40 A
20 A
20 A
20 A
30 A
100 A
50 A
1
2
3
4
20 A
7.5 A
15 A
15 A
LAF Heater
Daytime running lights
FI ECU (ECM/PCM)
IG Coil
21 257.5A 30A
Fuse Locations
T aking Care of t he Unexpect ed
241
Primary Fuse Box
Secondary Fuse Box
PRIMARY
SECONDARY
UNDER-HOOD FUSE BOXES

Î
Î
Î
Î
Î Î
Î
Specif ications
246
Capacities
Engine
Weights
Dimensions Capacities 181.0 in (4,597 mm)1.43 US gal (5.4)1.88 US gal (7.1)
1.45 US gal (5.5) 1.90 US gal (7.2)
3.3 US qt (3.1) 3.1 US qt (2.9)
7.6 US qt (7.2) 6.9 US qt (6.5)2.0 US qt (1.9)2.4 US qt (2.3)
1.1 US qt (1.0) 1.3 US qt (1.2)
4.8 US qt (4.5) 2.6 US qt (2.5)
0.16 US gal (0.6)
Excluding the oil remaining in the engine Including the coolant in the reserve tank and that remaining in theengineReserve tank capacity:
Fuel tank
Engine oil
5.6 US qt (5.3) 4.2 US qt (4.0)4.4 US qt (4.2)
15.3 US gal (58)
Type
BorexStroke DisplacementCompression ratioSpark plugs
Gross vehicle weight rating
Length
Width HeightWheelbaseTrack
See the certification label attached to the driver’s doorjamb.
SKJ20DR-M11 IZFR6K-119.6 : 1144 cu-in (2,354 cm)3.43 x 3.90 in (87.0 x 99.0 mm)
60.6 in (1,538 mm) 60.4 in (1,533 mm)103.1 in (2,620 mm)66.2 in (1,682 mm)70.2 in (1,782 mm)181.8 in (4,617 mm)Engine coolant
Automatic transmissionfluid
Manual transmissionfluidReardifferentialfluid (4WD)Windshieldwasherreservoir
Water cooled 4-stroke DOHC i-VTEC 4-cylinder gasoline engine
Approx.
Front Rear
Change
Without filter Total
1: 2:
Change Total
Change TotalChange4WD2WDTotal4WD2WDChangeTotal
Change Total
U.S. Vehicles CanadaVehicles (NGK) (DENSO)
1 : U.S. SE model and Canada EX-L model
Automatic Transmission
Manual Transmission
1
2
2
1
Including filter

CONT INUED
BatteryCharging System ...........................
Indicator .56, 233
............................
Jump Starting .229
..............................
Maintenance .217
............................
Specif ications .247
..............................
Bef ore Driving .141
....................................
Belts,Seat .8,18
...........................
Beverage Holders .91
..................................
Booster Seats .47
Brakes ...........
Anti-lock System (ABS) . 168
.............
Break-in, New Linings . 142
....................
Bulb Replacement .205
...........................................
Fluid .201
.........................................
Parking .68
.................
System Indicator . 56,235 ..........................
System Design .167
........................
Wear Indicators .167
.............................
Braking System .167
.................
Break-in, New Vehicle . 142
..
Brightness Control, Instruments . 67
..................
Brights, Headlights . 66,67
...................................
Built-in Table .91
Bulb Replacement ..........................
Back-up Lights .205
..............................
Brake Lights .205
................
Front Parking Lights . 205
........
Front Side Marker Lights . 205
.................................
Headlights .203
.........
High-mount Brake Light . 207
.........
Rear Side Marker Lights . 205
............................
Specif ications .247
....................
Turn Signal Lights . 205
..............................
Bulbs, Halogen .203
............................
Capacities Chart .246
.............
Carbon Monoxide Hazard . 50
..............................................
Cargo .150
....................................
Accessories .148
ACCESSORY (Ignition Key .......................................
Position) .72
..............
Accessory Power Sockets . 95
....................
Additives, Engine Oil . 193
.......
Adjusting the Steering Wheel . 69
...........................
Advanced Airbags .25
...............................
Airbag (SRS) .9, 21
................
Air Conditioning System . 98
.........................................
Usage .100
.......................
Air Pressure, Tires .213
.......................
Alcohol in Gasoline .142
......................................
Antif reeze .196
Anti-lock Brakes (ABS) ...............................
Indicator .57, 168
...................................
Operation .168
..............
Anti-thef t, Audio System . 136
.
Anti-thef t Steering Column Lock . 72
................................
Audio System .103
...
Automatic Seat Belt Tensioners . 19
.............
Automatic Speed Control . 138
..............
Automatic Transmission . 161
..........................
Capacity, Fluid .246
...............
Checking Fluid Level . 199....................................
D3 Mode .163
.......................................
Shif ting .161
Shif t Lever Position ...............................
Indicators .161
................
Shif t Lever Positions . 162
....................
Shif t Lock Release . 165
Index
A
B
C
INDEX
I