ignition HONDA CR-V 2006 RD4-RD7 / 2.G Owner's Manual

µµ
Avoid dropping or throwing the
transmitter.
Protect the transmitter from
extreme temperature.
Do not immerse the transmitter in
any liquid.
If you lose a transmitter, the
replacement needs to be
reprogrammed by your dealer.
If it takes several pushes on the
button to lock or unlock the doors
and the tailgate, replace the battery
as soon as possible.
Battery type: CR1616
To replace the battery:Remove the screw at the base of
the transmitter with a small
Phillips-head screwdriver.
Pressthisbuttonfor
about 2 seconds to attract attention:
the horn will sound, and the exterior
lights will f lash f or about 30 seconds.
To cancel panic mode, press any
other button on the remote
transmitter, or turn the ignition
switch to the ON (II) position. Press this button f or about 1 second
to open the hatch glass. You cannot
open the hatch glass if the key is in
the ignition switch. Even if the hatch
glass is open, the tailgate can be
locked with the remote transmitter.
1.
Remote Transmitter
Replacing the Transmitter
Battery
PA NIC HATCH GLASS RELEASERemote Transmitter Care
76
SCREW

Do not use the seat heaters when the
engine is of f or when idling f or a
long period of time. They can drain
the battery, making your vehicle
hard to start.Turn the ignition switch to the ON
(II) position to raise or lower any
window. To open the window, push
the switch down and hold it. Release
the switch when you want to stop the
window. Pull back on the switch and
hold it to close the window.
Both f ront seats are equipped with
seat heaters in the seat bottoms only.
Because of sensors f or the side
airbag system, there are no heaters
in the seat-back in either the driver
or passenger seats. The ignition
switch must be in the ON (II)
position to use them. Push the
heater switch to turn the power on or
of f . The indicators will come on and
remain on while the heaters are on.
If equipped
Seat Heaters, Power Windows
Seat Heaters
Power Windows
86
DRIVER’S SEAT HEATER SWITCH
PASSENGER’S SEAT HEATER SWITCH DRIVER’S WINDOW SWITCH
MAIN SWITCH

If equippedKeep the inside and outside mirrors
clean and adjusted f or best visibility.
Be sure to adjust the mirrors bef ore
you start driving.
The inside mirror has day and night
positions. The night position reduces
glare f rom headlights behind you.
Flip the tab on the bottom edge of
the mirror to select the day or night
position.
Turn the ignition switch to the ON
(II) position, and use the switch
under the lef t dashboard vent to
operate the moonroof .
To tilt up the back of the moonroof ,
press and hold the center button
().
To close the moonroof , press and
hold the top of the switch ( ).
To open the moonroof , press and hold the bottom of the switch
().
Moonroof
Mirrors
Moonroof , Mirrors
88
TABOpening or closing the
moonroof on someone’s hands
or fingers can cause serious
injury.
Make sure all hands and fingers
are clear of the moonroof
before opening or closing it.
If you try to open the moonroof in
below-f reezing temperatures, or when
it is covered with snow or ice, you can
damage the moonroof panel or motor.

Turn the ignition switch to the ON
(II) position.Push the appropriate edge of the
adjustment switch to move the
mirrorright,left,up,ordown.
When you f inish, move the
selector switch to the center (off)
position. This turns the
adjustment switch of f to keep your
settings.
The outside mirrors are heated to
remove fog and frost. With the
ignition switch in the ON (II)
position, turn on the heaters by
pressing the rear window def ogger
button. The indicator in the button
comesonasareminder.Pressthe
button again to turn the heaters and
the def ogger of f .
Move the selector switch to L
(driver’s side) or R (passenger’s
side).
2. 1. 3.
4.If equipped
Mirrors
Adjusting the Power Mirrors
Power Mirror Heaters
Inst rument s and Cont rols
89
SELECTOR SWITCH
ADJUSTMENT SWITCH REAR WINDOW DEFOGGER/
HEATED MIRRORS BUTTON

These sockets are intended to supply
power f or 12 volt DC accessories
that are rated 120 watts or less (10
amps).
To use an accessory power socket,
the ignition switch must be in the
ACCESSORY (I) or ON (II) position.
None of the sockets will power an
automotive type cigarette lighter
element. When more than one
socket is being used, the combined
power rating of the accessories
should be 120 watts or less
(10 amps).Open the center pocket by pulling
the handle.
To use the sun visor, pull it down.
Whenusingthesunvisorforthe
side window, remove the support rod
f rom the clip, and swing it out.The ceiling light has a three-position
switch; ON, Door Activated, and
OFF. In the Door Activated (center)
position, the light comes on when
you:
Open any door.
Unlock the doors and the tailgate
with the key or remote transmitter.
Only on models with an automatictransmission
CONT INUED
A ccessory Power Sockets Center Pocket
Sun Visor Ceiling L ight
Interior Convenience Items, Interior L ights
Inst rument s and Cont rols
95
ON
OFF DOOR ACTIVATED

After all doors are closed tightly, the
light f ades out in about 30 seconds.
The ceiling light (with the switch in
the center position) comes on when
you remove the key f rom the ignition
switch. If you do not open a door, the
light f ades out in about 30 seconds.
If you leave any door or the tailgate
open with the key not in the ignition
switch, the ceiling light will go of f
af ter 3 minutes.Turn on the spotlight by pushing the
button. Push the button again to turn
it of f . You can use the spotlights at
all times.
The ignition switch light comes on
when you open the driver’s door. It
f ades out in about 30 seconds af ter
the door is closed.The cargo area light has a three-
position switch. In the OFF position,
the light does not come on. In the
center position, the light comes on
when you open the tailgate or the
hatch glass. In the ON position, the
light stays on continuously.
Interior Lights
Spotlights
Ignition Switch L ightCargo A rea L ight
96
OFF
ON
TAILGATE/HATCH GLASS ACTIVATED

µ
µ ÓÓ µ
´µ
You can use any of f ive methods to
f ind radio stations on the selected
band:
the
preset buttons, and .
Use the TUNE knob to
tune the radio to a desired f requency.
Turn the knob right to tune to a
higher f requency, or lef t to tune to a
lower f requency.
The SEEK f unction
searches up and down from the
current f requency to f ind a station
with a strong signal. To activate it,
press the or SEEK button, then
release it.
The ignition switch must be in the
ACCESSORY (I) or ON (II) position.
Turn the system on by pushing the
PWR/VOL knob or the AM or FM
button. Adjust the volume by turning
the PWR/VOL knob.
The SCAN f unction
samples all stations with strong
signals on the selected band. To
activate it, press the SCAN button,
then release it. You will see SCAN in
the display. The system will scan f or
a station with a strong signal. When
it f inds one, it will stop and play that
station f or about 10 seconds.
If you do nothing, the system will
scan f or the next strong station and
play it f or 10 seconds. When it plays
a station that you want to listen to,
press the SCAN button again.
The band and f requency that the
radio was last tuned to is displayed.
To change bands, press the AM or
FM button. On the FM band, ST will
be displayed if the station is
broadcasting in stereo.
Stereo reproduction on AM is not
available. To Play the Radio
TUNE,SEEK,SCAN,AUTO SELECT
To Select a Station
TUNE
SEEK SCAN
Playing the Radio
106

µÓ
Ó
ÓÓ
µ
´
µ
´µ
If you turn the system of f while a CD
is playing, either with the PWR/VOL
knob or by turning off the ignition,
the disc will stay in the drive. When
youturnthesystembackon,theCD
will begin playing where it lef t of f . To play the tape when a CD is
playing, insert a tape in the player. If
a tape is in the player, press the
TAPE button. Press the CD button
again to switch back to the CD
player. To play the radio when a CD is
playing, press the AM or FM button.
Press the CD button again to switch
back to the CD player.
To load or play CDs, the ignition
switch must be in the ACCESSORY
(I) or the ON(II) position.
You operate the CD player with the
same controls used f or the radio. To
select the CD player, press the CD
button. The number of the track
playing is shown in the display. The
system will continuously play a CD
until you change modes.
Insert a CD into the CD slot. The
drive will pull the CD in the rest of
the way to play it. When the system
reaches the end of the disc, it will
return to the beginning and play the
disc again.
You can also play 3-inch (8-cm) discs
without using an adapter ring. Each time you press and
release the skip button, the player
skips forward to the beginning of the
next track. Press and release the
skip button, to skip backward to the
beginning of the current track. Press
it again to skip to the beginning of
the previous track.
To move rapidly within a track, press
andholdthe or skipbutton.
To continuously replay
a track, press and release the RPT
button. You will see REPEAT in the
display. Press it again to turn it of f .
T o Play a CD
T o Change or Select T racks
SK IP
REPEAT
Playing a Disc
110
Do not use discs with adhesive labels.
The label can curl up and cause the
disc to jam in the unit.

µ
µ
µ
´
This f eature plays the
tracks in random order. To activate
random play, press and release the
RDM button. You will see RDM in
the display. Press it again to return
to normal play.
The SCAN f unction
samples all the tracks on the disc in
the order they are recorded on the
CD. To activate it, press and hold the
SCAN button. You will see SCAN in
the display. You will get a 10 second
sampling of each track on the CD.
Press the SCAN button again to get
out of the system and play the last
track sampled.
Press the eject button ( ) to
remove the CD. If you eject the CD,
but do not remove it f rom the slot,
the system will automatically reload
the CD af ter 10 seconds and put it in
pause mode. To begin playing, press
the CD button. Press the AM or FM button to
switch to the radio while a CD is
playing. To play the CD, press the
CD button.
If a tape is in the tape player, press
the TAPE button to switch to the
tape while a CD is playing. Press the
CD button again to switch back to
the CD player.
If you turn the system of f while a CD
is playing, either with the PWR/VOL
knob or by turning off the ignition,
the disc will stay in the drive. When
youturnthesystembackon,theCD
will begin playing where it lef t of f .
For inf ormation on how to handle
and protect discs, see page .
An optional six disc CD changer is
available f rom your dealer.
This disc changer uses the same
controls used f or the in-dash CD
player or the radio.
Load the desired CDs in the
magazine, and load the magazine in
the changer according to the
instructions that came with it.
To select the CD changer, press the
CD button. The CD and track
numbers will be displayed. To select
a dif f erent CD, use the preset 5
(DISC ) button to select the
previous disc, or the preset 6 (DISC
) button to select the next disc in
sequence. If you select an empty slot
in the magazine, the changer will
search for the next available CD to
load and play.
134
Playing a Disc
RANDOM
SCAN
T o Stop Playing a CD
Protecting Discs Operating Optional CD Changer
Features
111

Î
Î
Ûµ
µÓ Ó
µ
´
Dolby noise reduction is manufactured under
license from Dolby Laboratories Licensing
Corporation. ‘‘DOLBY’’ and the double-D symbol are trademarks of Dolby Laboratories
Licensing Corporation.
Dolby noise reduction turns on
when you insert a tape. The indicator will light in the
display. If the tape was not recorded
in Dolby, turn it of f by pressing the button. Dolby remains of f until
you press the button again.
To remove the tape, press the eject
button. If you want to turn the player
off, press the PWR/VOL knob or
turn off the ignition. The tape will
remain in the drive. When you turn
the system back on, the tape will
begin playing where it lef t of f .
The ignition switch must be in the
ACCESSORY (I) or the ON (II)
position. Make sure the open side of
thetapeisfacingright,theninsert
thetapemostof thewayintotheslot.
Thesystemwillpullthetapeinthe
rest of the way and begin to play it.
Thetapedirectionindicatorinthe
display comes on to show you which
side of the tape is playing. The
indicates the side you inserted
upward is now playing. If you want to
play the other side, press the PROG
button. When the player reaches the
end of the tape, it will automatically
reverse direction and play the other
side.
To switch to the radio or CD player
while a tape is playing, press the AM,
FM, or CD button. To change back
to the tape player, press the TAPE
button.
To rewind the tape,
push the REW button. You will see
REW in the display. To fast forward
the tape, push the FF button. You
will see FF displayed. Press the FF,
REW, or PLAY button to take the
system out of rewind or f ast f orward.
Press the button to find
the beginning of the current song or
passage. Press the button to f ind
the beginning of the next song or
passage. When the system reaches
the beginning of a song or passage, it
begins to play it.
To Play a Tape
To Stop Playing a TapeT ape Search Functions
FF/REW
SK IP
Playing a T ape
114