HONDA CR-V 2020 Owner's Manual (in English)
Manufacturer: HONDA, Model Year: 2020, Model line: CR-V, Model: HONDA CR-V 2020Pages: 671, PDF Size: 33.11 MB
Page 591 of 671

589
uuChecking and Maintaining Wiper Blades uChanging the Rear Wiper Blade Rubber
Maintenance
5. Slide the new wiper bl ade onto the holder.
u Make sure it is engaged correctly, then 
install the wiper blade assembly onto the 
wiper arm.
Holder
20 CR-V PET ELP_MAP_HMIN_HCM_J-31TLA6310.book  589 ページ  2019年10月3日 木曜日 午後4時55分 
Page 592 of 671

590
Maintenance
Checking and Maintaining Tires
Checking Tires
To safely operate your vehicle, your tires must be of the proper type and size, in 
good condition with adequate tread, and properly inflated.
■Inflation guidelines
Properly inflated tires provide  the best combination of handling, tread life, and comfort. 
Refer to the driver’s doorjamb label or spec ifications page for the specified pressure.
Underinflated tires wear unevenly, adversely affect handling and fuel economy, and 
are more likely to fail from overheating.
Overinflated tires make your vehicle ride harshly, are more prone to road hazards, 
and wear unevenly.
Every day before you drive, look at each of  the tires. If one looks lower than the 
others, check the pressure with a tire gauge.
At least once a month or before long trips, use a gauge to measure the pressure in 
all tires, including the spare. Even tires in good condition can lose 1–2 psi 
(10–20 kPa, 0.1–0.2 kgf/cm
2) per month.
■Inspection guidelines
Every time you check inflation, also  examine the tires and valve stems.
Look for:
• Bumps or bulges on the side or in the tread. Replace the tire if you find any cuts, 
splits, or cracks in the si de of the tire. Replace it if you see fabric or cord.
• Remove any foreign objects  and inspect for air leaks.
• Uneven tread wear. Have a deal er check the wheel alignment.
• Excessive tread wear.
2 Wear Indicators  P. 595
•Cracks or other damage around valve stem.
1Checking Tires
Measure the air pressure when tires are cold. This 
means the vehicle has been parked for at least three 
hours, or driven less than 1 mile (1.6 km). If 
necessary, add or releas e air until the specified 
pressure is reached.
If checked when hot, tire pressure can be as much as 
4–6 psi (30–40 kPa, 0.3–0.4 kgf/cm
2) higher than if 
checked when cold.
Whenever tire pressure is adjusted, you must 
calibrate the TPMS. 2 Tire Pressure Monitoring System (TPMS)  
P. 522
Have a dealer check the tires if you feel a consistent 
vibration while driving. Ne w tires and any that have 
been removed and reinst alled should be properly 
balanced.
Check the spare tire pressu re once a month or before 
long trips.
3WARNING
Using tires that are excessively worn or 
improperly inflated can cause a crash in 
which you can be seriously hurt or killed.
Follow all instruction s in this owner’s 
manual regarding ti re inflation and 
maintenance.
20 CR-V PET ELP_MAP_HMIN_HCM_J-31TLA6310.book  590 ページ  2019年10月3日 木曜日 午後4時55分 
Page 593 of 671

591
uuChecking and Maintaining Tires uTire and Loading Information Label
Continued
Maintenance
Tire and Loading Information Label
The label attached to the driver’s doorj amb provides necessary tire and loading 
information.
Tire Labeling
The tires that came on your vehicle have a 
number of markings. Those you should be 
aware of are described below.
Whenever tires are replaced,  they should be replaced with tires of the same size.
1Tire and Loading Information Label
The tire and loading informat ion label attached to the 
driver’s doorjamb contains:
aThe number of people your vehicle can carry.
bThe total weight your vehicle can carry. Do not 
exceed this weight.
cThe original tire sizes for front, rear, and spare.
dThe proper cold tire pressure for front, rear, and 
spare.
Label 
Example
Example Tire Size
Tire 
Identification 
Number (TIN)
Maximum 
Tire Load
Maximum 
Tire Pressure
Tire Size
■Tire Sizes
1 Tire Sizes
Following is an example  of tire size with an 
explanation of what  each component means.
P235/60 R18 102T
P: Vehicle type (P indi cates passenger vehicle).
235: Tire width in millimeters.
60: Aspect ratio (the tire’s section height as a 
percentage of its width).
R: Tire construction code  (R indicates radial).
18: Rim diameter in inches.
102: Load index (a numerical  code associated with 
the maximum load the tire can carry).
T: Speed symbol (an alphabetical code indicating the 
maximum speed rating).
20 CR-V PET ELP_MAP_HMIN_HCM_J-31TLA6310.book  591 ページ  2019年10月3日 木曜日 午後4時55分 
Page 594 of 671

uuChecking and Maintaining Tires uTire Labeling
592
Maintenance
The tire identification number (TIN) is a gr oup of numbers and letters that look like 
the example in the side co lumn. TIN is located on the sidewall of the tire.
Cold Tire Pressure  – The tire air pressure when the vehicle has been parked for at 
least three hours or driven  less than 1 mile (1.6 km).
Load Rating  – Means the maximum load that a ti re is rated to carry for a given 
inflation pressure.
Maximum Inflation Pressure  – The maximum tire air pressure that the tire can 
hold.
Maximum Load Rating  – Means the load rating for a tire at the maximum 
permissible inflation pr essure for that tire.
Recommended Inflation Pressure  – The cold tire inflation pressure recommended 
by the manufacturer.
Treadwear Indicators (TWI)  – Means the projections within the principal grooves 
designed to give a visual indication of the degrees of wear of the tread.
■Tire Identification Number (TIN)
■Glossary of Tire Terminology
1 Tire Identification Number (TIN)
DOT B97R FW6X 2209
DOT: This indicates that the tire meets all 
requirements of the  U.S. Department of 
Transportation.
B97R: Manufacturer's identification mark.
FW6X: Tire type code.
22 09: Date of manufacture.
Year
Week
20 CR-V PET ELP_MAP_HMIN_HCM_J-31TLA6310.book  592 ページ  2019年10月3日 木曜日 午後4時55分 
Page 595 of 671

593
uuChecking and Maintaining Tires uDOT Tire Quality Grading (U.S. Vehicles)
Continued
Maintenance
DOT Tire Quality Grading (U.S. Vehicles)
The tires on your vehicle m eet all U.S. Federal Safety 
Requirements. All tires are also  graded for treadwear, traction, 
and temperature performance according to Department of 
Transportation (DOT) standards.  The following explains these 
gradings.
Quality grades can be found where applicable on th e tire sidewall 
between tread shoulder and maximum section width.
The treadwear grade is a comparative rating based on the wear 
rate of the tire when tested un der controlled conditions on a 
specified government test course.  For example, a tire graded 150 
would wear one and one-half (1 1/2) times as well on the 
government course as a tire graded 100. The relative performance 
of tires depends upon the actual conditions of their use, however, 
and may depart significantly from  the norm due to variations in 
driving habits, service practi ces and differences in road 
characteristics and climate.
■Uniform Tire Quality Grading
■Treadwear
1 Uniform Tire Quality Grading
For example:
Treadwear 200
Traction AA
Temperature A
All passenger car tires must conform 
to Federal Safety Requirements in 
addition to these grades.
20 CR-V PET ELP_MAP_HMIN_HCM_J-31TLA6310.book  593 ページ  2019年10月3日 木曜日 午後4時55分 
Page 596 of 671

uuChecking and Maintaining Tires uDOT Tire Quality Grading (U.S. Vehicles)
594
Maintenance
The traction grades, from highest to  lowest, are AA, A, B, and C. 
Those grades represent the tire's  ability to stop on wet pavement 
as measured under controlled conditions on specified 
government test surfaces of asphalt and concrete. A tire marked 
C may have poor traction performance.
The temperature grades are A (the highest), B, and C, 
representing the tire's resistance  to the generation of heat and its 
ability to dissipate h eat when tested under  controlled conditions 
on a specified indoor laboratory test wheel. Sustained high 
temperature can cause the material  of the tire to degenerate and 
reduce tire life, and excessive temp erature can lead to sudden tire 
failure. The grade C corresponds to a level of performance which 
all passenger car tires must meet under the Federal Motor Vehicle 
Safety Standard No. 109. Grades  B and A represent higher levels 
of performance on the laboratory  test wheel than the minimum 
required by law.
■Traction
■Temperature
1 Traction
Warning: The traction grade 
assigned to this tire is based on 
straight-ahead braking traction tests, 
and does not include acceleration, 
cornering, hydroplaning, or peak 
traction characteristics.
1Temperature
Warning: The temperature grade for 
this tire is establishe d for a tire that is 
properly inflated and not 
overloaded. Excessive speed, 
underinflation, or excessive loading, 
either separately or in combination, 
can cause heat buildup and possible 
tire failure.
20 CR-V PET ELP_MAP_HMIN_HCM_J-31TLA6310.book  594 ページ  2019年10月3日 木曜日 午後4時55分 
Page 597 of 671

595
uuChecking and Maintaining Tires uWear Indicators
Maintenance
Wear Indicators
The groove where the wear indicator is 
located is 1/16 inch (1.6 mm) shallower than 
elsewhere on the tire. If  the tread has worn so 
that the indicator is ex posed, replace the tire. 
Worn out tires have po or traction on wet 
roads.
Tire Service Life
The life of your tires is dependent on many factors, including driving habits, road 
conditions, vehicle loading, inflation pressure, maintenance history, speed, and 
environmental conditions (even wh en the tires are not in use).
In addition to regular inspections and in flation pressure maintenance, it is 
recommended that you have annual inspections  performed once the tires reach five 
years old. All tires, including the spare, should be removed from service after 10 
years from the date of manufacture, regardle ss of their condition or state of wear.
Example of a Wear 
Indicator mark
20 CR-V PET ELP_MAP_HMIN_HCM_J-31TLA6310.book  595 ページ  2019年10月3日 木曜日 午後4時55分 
Page 598 of 671

596
uuChecking and Maintaining Tires uTire and Wheel Replacement
Maintenance
Tire and Wheel Replacement
Replace your tires with radials of the sa me size, load range, speed rating, and 
maximum cold tire pressure ra ting (as shown on the tire‘s sidewall). Using tires of a 
different size or construction can cause ce rtain vehicle systems such as the ABS and 
Vehicle Stability Assist
TM (VSA ®) system to work incorrectly.
It is best to replace all four tires at the  same time. If that isn’t possible, replace the 
front or rear tires in pairs.
Make sure that the wheel’s specifications match thos e of the original wheels.
1Tire and Wheel Replacement
3WARNING
Installing improper tires on your vehicle can 
affect handling and stability. This can cause 
a crash in which you can be seriously hurt or 
killed.
Always use the size and type of tires 
recommended in this owner’s manual.
20 CR-V PET ELP_MAP_HMIN_HCM_J-31TLA6310.book  596 ページ  2019年10月3日 木曜日 午後4時55分 
Page 599 of 671

597
uuChecking and Maintaining Tires uTire Rotation
Maintenance
Tire Rotation
Rotating tires according to the maintena nce messages on the driver information 
interface helps to distribute wear  more evenly and increase tire life.
■Tires without rotation marks
Rotate the tires as shown here.
■Tires with rotation marksRotate the tires as shown here.
1Tire Rotation
Tires with directional trea d patterns should only be 
rotated front to back (not fr om one side to the other).
Directional tires should be  mounted with the rotation 
indication mark  facing forward, as shown below.
Whenever tires are rotated, you must calibrate the 
TPMS. 2 Tire Pressure Monitoring System (TPMS)  
P. 522
Front
Direction MarkFront
Front
20 CR-V PET ELP_MAP_HMIN_HCM_J-31TLA6310.book  597 ページ  2019年10月3日 木曜日 午後4時55分 
Page 600 of 671

598
uuChecking and Maintaining Tires uWinter Tires
Maintenance
Winter Tires
If driving on snowy or frozen roads, mount all season marked “M+S” tires, snow 
tires, or tire chains; reduce speed; and ma intain sufficient distance between vehicles 
when driving.
Be particularly careful when operating  the steering wheel or brakes to prevent 
skidding.
Use tire chains, snow tires, or all season ti res when necessary or according to the law.
When mounting, refer to  the following points.
For winter tires:
• Select the size and load ranges that  are the same as the original tires.
• Mount the tires to all four wheels.
For tire chains:
• Install them on the front tires only.
• Because your vehicle has limited tire cl earance, we strongly recommend using the 
chains listed below:
• Follow the chain manufacturer's instruction when installing. Mount them as 
tightly as you can.
• Check that the chains do not to uch the brake lines or suspension.
• Drive slowly.
Cable-type: SCC RADIAL CHAIN TC2111MM
Cable-type: SCC RADIAL CHAIN TC2212MM
1Winter Tires
NOTICE
Traction devices that are the wrong size or improperly 
installed can damage your  vehicle's brake lines, 
suspension, body, and wheels. Stop driving if they are 
hitting any part  of the vehicle.
When tire chains are mounted, follow the chain 
manufacturer's instructi ons regarding vehicle 
operational limits.
If your vehicle is equipp ed with summer tires, be 
aware that these tires are not designed for winter 
driving conditions. For more information, contact a 
dealer.
3WARNING
Using the wrong chains, or not properly 
installing chains, can damage the brake 
lines and cause a crash in which you can be 
seriously injured or killed.
Follow all instruction s in this owner's 
manual regarding the selection and use of 
tire chains.
Models with 235/65R17 tires
Models with 235/55R19 tires
Models with 235/60R18 tires
20 CR-V PET ELP_MAP_HMIN_HCM_J-31TLA6310.book  598 ページ  2019年10月3日 木曜日 午後4時55分