manual transmission HONDA ELEMENT 2003 1.G User Guide

Fill the reserve tank to the MAX
mark. Install the reserve tank cap.
Install the radiator cap, and
tighten it to the first stop.Remove the radiator cap. Fill the
radiator with coolant up to the
base of the f iller neck.
Start the engine and hold it at
1,500 rpm until the radiator f an
comes on. Turn of f the engine.
Check the coolant level in the
radiator and add coolant if needed.
Install the radiator cap, and
tighten it fully.
If necessary, f ill the reserve tank
to the MAX mark. Install the
reserve tank cap.
Start the engine and let it run until
the radiator cooling f an comes on
at least twice. Then stop the
engine.
Start the engine and let it run f or
about 30 seconds. Then turn of f
the engine.
Check the level in the radiator,
add coolant if needed.
The cooling system capacity is:
9.
10. 11.
12.
13.14.
15.
16.
17.
With automatic transmission:
With manual transmission:
Maint enance
Cooling Syst em
229
1.43 US gal (5.4)
1.45 US gal (5.5
)

Insert the dipstick all the way back
into the transmission securely as
shown in the illustration.
The transmission should be drained
and ref illed with new f luid according
to the time and distance recommen-
dations in the maintenance schedule.
Check the f luid level with the
transmission at normal operating
temperature and the vehicle sitting
on level ground. Remove the
transmission f iller bolt and caref ully
f eel inside the bolt hole with your
f inger. The f luid level should be up
to the edge of the bolt hole. If it is
not, add Honda Manual
Transmission Fluid (MTF) until it
starts to run out of the hole.Put a new washer on the f iller bolt,
then reinstall the f iller bolt and
tighten it securely.
If you are not sure how to add f luid,
contact your Honda dealer. If Honda MTF is not available, you
may use an SAE 10W-30 or 10W-40
viscosity motor oil with the API
Certif ication seal that says ‘‘FOR
GASOLINE ENGINES’’ as a
temporary replacement. However,
motor oil does not contain the proper
additives, and continued use can
cause stif f er shif ting. Replace as
soon as it is convenient.
The transmission should be drained
and ref illed with new f luid according
to the time and distance recommen-
dations in the maintenance schedule.
6.
5-speed Manual Transmission
T ransmission Fluid
Maint enance232
WASHER FILLER BOLT
Correct level

The f luid level should be between
theMINandMAXmarksontheside
of the reservoir. If the level is at or
below the MIN mark, your brake
system needs attention. Have the
brake system inspected f or leaks or
worn brake pads.
Always use Honda Heavy Duty
Brake Fluid DOT 3. If it is not
available, you should use only DOT 3
or DOT 4 f luid, f rom a sealed
container, as a temporary
replacement. However, the use of
any non-Honda brake fluid can cause
corrosion and decrease the lif e of the
system. Have the brake system
f lushed and ref illed with Honda
Heavy Duty Brake Fluid DOT 3 as
soon as possible.
Check the f luid level in the reser-
voirs monthly. There are up to two
reservoirs, depending on the model.
They are:
Brake f luid reservoir (all models)
Clutch f luid reservoir
(manual transmission only)
The brake f luid should be replaced
according to the time recommenda-
tion in the maintenance schedule. Brake f luid marked DOT 5 is not
compatible with your vehicle’s
braking system and can cause
extensive damage.Brake System
Brake and Clutch Fluid
Maint enance234
MIN
MAX

If you need to park your vehicle f or
an extended period (more than one
month), there are several things you
should do to prepare it f or storage.
Proper preparation helps prevent
deterioration and makes it easier to
get your vehicle back on the road. If
possible, store your vehicle indoors.Block the rear wheels.
If the vehicle is to be stored f or a
longer period, it should be
supported on jackstands so the
tires are of f the ground.
Leave one window open slightly (if
the vehicle is being stored
indoors).Cover the vehicle with a
‘‘breathable’’ cover, one made
f rom a porous material such as
cotton. Nonporous materials, such
as plastic sheeting, trap moisture,
which can damage the paint.
Fill the f uel tank.
Change the engine oil and f ilter
(see page ).
Wash and dry the exterior
completely.
Cleantheinterior.Makesurethe
carpeting, floor mats, etc. are
completely dry. To minimize sticking, apply a
silicone spray lubricant to all door
and tailgate seals. Also, apply a
vehiclebodywaxtothepainted
surfaces that mate with the door
and tailgate seals. Support the f ront and rear wiper
blade arms with a f olded towel or
ragsotheydonottouchthe
windshield. Disconnect the battery.
Leave the parking brake off. Put
the transmission in Reverse
(5-speed manual) or Park
(automatic). If possible, run the engine f or a
while periodically (pref erably once
amonth).
If you store your vehicle f or 12
months or longer, have your Honda
dealer perf orm the inspections called
f or in the 24 months maintenance
schedule (Normal Conditions) as
soon as you take it out of storage
(see page ). The replacements
called f or in the maintenance
schedule are not needed unless the
vehicle has actually reached that
time or mileage.
223
212
St oring Your Vehicle
Maint enance266

If you have a f lat tire while driving,
stop in a saf e place to change it.
Stopping in traf f ic or on the shoulder
of a busy road is dangerous. Drive
slowly along the shoulder until you
gettoanexitoranareatostopthat
is far away from the traffic lanes.Park the vehicle on f irm, level and
non-slippery ground, away f rom
traffic. Put the transmission in
Park (automatic) or Reverse
(manual). Apply the parking brake.
Turn on the hazard warning lights,
and turn the ignition switch to
LOCK (0). Have all the
passengers get out of the vehicle
while you change the tire. If you are towing a trailer, unhitch
the trailer.Open the hatch and the tailgate.
The spare tire, jack, and tools are
under the cargo area f loor.
1.
2. 3.
4.
CONT INUED
Changing a Flat T ire
T aking Care of t he Unexpect ed277
JACK SPARE TIRETOOLS
The vehicle can easily roll off
the jack, seriously injuring
anyone underneath.
Follow the directions for
changing a tire exactly, and
never get under the vehicle
when it is supported only by the
jack.

Diagnosing why your engine won’t
start f alls into two areas, depending
on what you hear when you turn the
key to START (III):You hear nothing, or almost
nothing. The engine’s starter
motor does not operate at all, or
operates very slowly.
You can hear the starter motor
operating normally, or the starter
motor sounds like it is spinning
f aster than normal, but the engine
does not start up and run. Turn the ignition switch to ON (II).
Turn on the headlights and check
their brightness. If the headlights
are very dim or don’t light at all,
the battery is discharged. See
on page .
When you turn the ignition switch to
START (III), you do not hear the
normal noise of the engine trying to
start. You may hear a clicking sound
or series of clicks, or nothing at all.
Check these things:
Turn the ignition switch to START
(III). If the headlights do not dim,
check the condition of the f uses. If
the f uses are OK, there is proba-
bly something wrong with the
electrical circuit f or the ignition
switch or starter motor. You will
need a qualif ied technician to
determine the problem. (See on page .)
Check the transmission interlock.
If you have a manual transmission,
the clutch pedal must be pushed
all the way to the f loor or the
starter will not operate. With an
automatic transmission, it must be
in Park or Neutral. 285
301
CONT INUED
Nothing Happens or the Starter
Motor Operates Very Slowly Jump Starting
Emergency T owing
If Your Engine Won’t Start
T aking Care of t he Unexpect ed283

The Engine Number is stamped into
the engine block.
The Transmission Number is on a
label on top of the transmission.
Identif ication Numbers
T echnical Inf ormation305
ENGINE NUMBERMANUAL TRANSMISSION NUMBER
AUTOMATIC TRANSMISSION NUMBER

ÎÎ
ÎÎ
Î
Specif ications
T echnical Inf ormation306
Dimensions
Weights
Capacities Engine
169.3 in (4,300 mm)
71.5 in (1,815 mm)
70.4 in (1,788 mm)
101.4 in (2,575 mm)
62.1 in (1,577 mm)
62.3 in (1,582 mm)
1.88 US gal (7.1
)
1.90 US gal (7.2
)
3.3 US qt (3.1
)
7.6 US qt (7.2
)
2.0 US qt (1.9
)
Length
Width
Height
Wheelbase
Track
Gross vehicle weight rating
1.43 US gal (5.4
)
3.1 US qt (2.9
)
1.45 US gal (5.5
)
6.9 US qt (6.5
)
5.6 US qt (5.3
)
4.2 US qt (4.0)
4.4 US qt (4.2)
15.9 US gal (60
)
Fuel tank
Engine oil Type
BorexStroke
Displacement
Compression ratio
Spark plugs 9.7 : 1
144 cu-in (2,354 cm
)
3.43 x 3.90 in (87.0 x 99.0 mm) Water cooled 4-stroke DOHC
VTEC 4-cylinder gasoline engine
See the certification label attached
to the driver’s doorjamb (front
edge of rear door).
See spark plug maintenance
section page 239 .
0.145 US gal (0.55
)
Including the coolant in the reserve tank and that remaining in the
engine.
Reserve tank capacity: Excluding the oil remaining in the engine.
Engine
coolant
Automatic
transmission
fluid
Manual
transmission
fluid
Rear
differential
fluid (4WD)
Windshield
washer
reservoir
4.8 US qt (4.5
)
2.6 US qt (2.5)
1.3 US qt (1.2
)
1.1 US qt (1.0)
2.4 US qt (2.3
)
2.3 US qt (2.2)
Approx.
Front
Rear
Change
Without filter
Total 1:
2:Change
Total
Change
Total
Change
4WD
2WD
Total 4WD
2WD
Change
Total 4WD
2WD
Change
Total
U.S. Vehicles
Canada
Vehicles
Automatic Transmission
Manual Transmission
1 2
2
Including filter

If you take your vehicle f or a state
emissions test shortly af ter the
battery has been disconnected or
gone dead, it may not pass the test.
This is because of certain ‘‘readiness
codes’’ that must be set in the on-
board diagnostics f or the emissions
systems. These codes are erased
when the battery is disconnected,
and set again only after several days
of driving under a variety of
conditions.If the testing f acility determines that
the readiness codes are not set, you
will be requested to return at a later
date to complete the test. If you must
get the vehicle re-tested within the
next two or three days, you can
condition the vehicle for re-testing
by doing the f ollowing.
Make sure the gas tank is nearly,
but not completely, f ull (around
3/4).
Make sure the vehicle has been
parked with the engine of f f or 8
hours or more.
Make sure the ambient
temperature is between 20° and
95°F. Without touching the accelerator
pedal, start the engine and let it
idle f or 20 seconds.
Keep the vehicle in Park
(automatic transmission) or
Neutral (manual transmission).
Increase the engine speed to 2,000
rpm and hold it there until the
temperature gauge rises to at least
1/4of thescale(approximately3
minutes).
T esting of Readiness Codes
St at e Emissions T est ing
T echnical Inf ormation316

CONT INUED
......................
Power Door Locks .87
..........
DOT Tire Quality Grading . 308
Downshif ting, 5-speed Manual
.............................
Transmission .176
.......................................
Drive Belt .248
...........................................
Driving .171
....................................
Economy .164
.........................
In Bad Weather .189
................
In Foreign Countries . 312
........................
Driving Guidelines .172
..................
Dust and Pollen Filter . 246
..............................
Economy, Fuel .164
............
Emergencies on the Road . 275
.............
Battery, Jump Starting . 285
...........
Brake System Indicator . 294
................
Changing a Flat Tire . 277
.....
Charging System Indicator . 291
..................
Checking the Fuses . 296
.....
Low Oil Pressure Indicator . 290
...
Malf unction Indicator Lamp . 292
..................
Overheated Engine . 288
.........................
Emergency Brake .111
......................
Emergency Flashers .81 ......................
Emergency Towing .301
.......................
Emissions Controls .313
.............
Emissions Testing, State . 316
Engine ....
Coolant Temperature Gauge . 74
...................................
Drive Belt .248
......
Engine Speed Limiter . 177,182
Malf unction Indicator ................................
Lamp .66, 292
........
Oil Pressure Indicator . 66,290
..............
Oil, What Kind to Use . 221
...............................
Overheating .288
............................
Specif ications .306
.......................................
Starting .174
......................
Ethanol in Gasoline .311
.
Evaporative Emissions Controls . 313
...............................
Exhaust Fumes .60
Expectant Mothers, Use of Seat ........................................
Belts by .21
..................
Exterior, Cleaning the . 268
............................
Fabric, Cleaning .271
...................................
Fan, Interior .118 Features, Comfort and
..............................
Convenience .117
....................
Filling the Fuel Tank . 159
Filters ................................
Air Cleaner .236
.........................
Dust and Pollen .246
...............................................
Oil .223
5-speed Manual Transmission ...............
Checking Fluid Level . 232
................................
Shif ting the .176
.............
Flashers, Hazard Warning . 81
...................
Flat Tire, Changing a . 277
Fluids ..........
Automatic Transmission . 231
..........................................
Brake .234
.........................................
Clutch .235
..............
Manual Transmission . 232
..........................
Power Steering .235
.......................
Rear Differential .233
..................
Windshield Washer . 230
FM Stereo Radio ...................................
Reception .143
...........................
Folding Rear Seat .99
.....
Foreign Countries, Driving in . 312
Index
E
F
III