remove seats HONDA ELEMENT 2004 1.G Owners Manual

CONT INUED
Your vehicle is equipped with
LATCH (Lower Anchors and
Tethers f or Children) at the rear
seats. The lower anchors are located
between the seat-back and seat
bottom, and are to be used only with
a child seat designed f or use with
LATCH.Make sure there are no objects
near the anchors that could
prevent a secure connection
between the child seat and
anchors.
To install a LATCH-compatible child
seat:
Place the child seat on the vehicle
seat, and attach the seat to the
lower anchors according to the
child seat maker’s instructions.
Some LATCH-compatible seats
have a rigid-type connection as
shown above.
Remove both anchor covers by
pulling f orward.
The location of each lower anchor is
marked with a small button above
the point. 1. 2.
3.
Installing a Child Seat Using
LATCH
Installing a Child Seat
Driver and Passenger Saf ety39
Rigid type
MARKS
ANCHOR COVER
—
—y
y
(+
yy

Other LATCH-compatible seats have
a f lexible-type connection as shown
above.Whatever type you have, f ollow
the child seat maker’s instructions
f or adjusting or tightening the f it. Remove the head restraint (see
page ). Make sure the removed
head restraints are secured in the
cargo area, and reinstalled when
the child seat is removed.
Slide the anchor cover open.
Route the tether strap over the top
of the seat-back, making sure the
strap is not twisted.
5.
4. 6.7.
75
Installing a Child Seat
Driver and Passenger Saf ety40
Flexible type TETHER ANCHOR
ANCHOR COVER
—
—y
y
(+
yy

See page f or important saf etyinf ormation and a warning about how toproperly position the head restraints. 14
The head restraints help protect you
and your passengers f rom whiplash
and other injuries. They are most
ef f ective when you adjust them so
the back of the occupant’s head rests
against the center of the restraint.
Your vehicle is equipped with head
restraints in all seating positions. The head restraints adjust f or height.
To raise it, pull upward. To lower the
restraint, push the release button
sideways and push the restraint
down.
To remove a head restraint f or
cleaning or repair, pull it up as f ar as
it will go. Push the release button,
then pull the restraint out of the seat-
back.
The rear seat passengers can get out
through the passenger’s door. Push
down on the release lever at the base
of the f ront passenger’s seat-back,
and push the seat-back forward. The
seat-back will tilt f orward and the
entire seat will move forward.
Make sure the seat is upright and
f ully latched bef ore sitting in it.
Seats
Inst rument s and Cont rols
Head Restraints Rear Seat Access
75
RELEASE BUTTONRELEASE LEVER
—
—y
y
(+
yy

You can recline the seat-backs on the
f ront seats so they are level with the
rear seat cushions, making a large
cushioned area. To do this:Adjust the front seats forward as
f ar as they will go. Pull up the seat-
back angle adjustment lever and
pivot the seat-back backward until
it is level with the rear seat
cushion.
Move the f ront seat backward
until it touches the rear seat.
Adjust the rear seat-back to the
desired position.
Reverse this procedure to return the
f ront and rear seats to the upright
position. Make sure you install the
head restraints and the seats are
locked securely bef ore driving.
When you return the seat-back to
the upright position, hold the seat-
back to keep it f rom going up too
quickly.
Remove the head restraints f rom
the f ront seats (see page ), and
store them in the side pockets of
the cargo area.
1. 2. 3. 4.
75
Reclining the Front Seats
Seats
Inst rument s and Cont rols76
—
—y
y
(+
y
y

Both seats can be removed to give
more cargo capacity. To remove a
seat:Pull the release strap on the seat
support to unlock the seat support. Remove the cover between the
seat cushion and the side wall by
pulling the tab and pulling the
cover straight up.
Push the lock lever f orward to
unlock the seat.
1. 3.
2.
CONT INUED
Removing the Rear Seats
Seats
Inst rument s and Cont rols79
RELEASE STRAP
COVERTAB
LOCK LEVER STEEL HANDLE
—
—y
y
(+
yy

Hold the steel handle next to the
lock lever and the holding strap at
the outside edge of the seat
cushion, and remove the entire
seat by pulling it up and backward.Reverse this procedure to reinstall
the seat. Make sure the seat is
securely locked.
Always remove an unsecured seat
f rom the vehicle bef ore driving. A
seat that is not locked in place could
be thrown about and cause injury in
a sudden stop or crash.
4.
Seats
Inst rument s and Cont rols80
STEEL HANDLE
HANDLE STRAP
—
—y
y
(+
yy