automatic transmission HONDA ELEMENT 2007 1.G Owner's Manual

Fill the f uel tank.
Change the engine oil and f ilter.
Wash and dry the exterior
completely.
Cleantheinterior.Makesurethe
carpeting, floor mats, etc., are
completely dry.Block the rear wheels.
If the vehicle is to be stored f or a
longer period, it should be
supported on jackstands so the
tires are of f the ground.
Cover the vehicle with a
‘‘breathable’’ cover, one made
f rom a porous material such as
cotton. Non-porous materials, such
as plastic sheeting, trap moisture,
which can damage the paint.
If you need to park your vehicle f or
an extended period (more than 1
month), there are several things you
should do to prepare it f or storage.
Proper preparation helps prevent
deterioration and makes it easier to
get your vehicle back on the road. If
possible, store your vehicle indoors. Leave one window open slightly (if
the vehicle is being stored
indoors).
Disconnect the battery.
Support the f ront and rear wiper
blade arms with a f olded towel or
ragsotheydonottouchthe
windshield.
To minimize sticking, apply a
silicone spray lubricant to all door
and tailgate seals. Also, apply a
vehiclebodywaxtothepainted
surfaces that mate with the door
and tailgate seals.
Leave the parking brake off. Put
the transmission in reverse
(manual) or Park (automatic). If possible, periodically run the
engine until it reaches f ull
operating temperature (the
cooling f ans cycle on and of f
twice). Pref erably, do this once a
month.
Vehicle Storage
Maint enance
215

If you have a f lat tire while driving,
stop in a saf e place to change it.
Drive slowly along the shoulder until
you get to an exit or an area to stop
that is far away from the traffic lanes.Open the hatch and the tailgate.
The spare tire, jack, and tools are
under the cargo area f loor.
Park the vehicle on f irm, level, and
non-slippery ground. Put the
transmission in Park (automatic)
or reverse (manual). Apply the
parking brake.
If you are towing a trailer, unhitch
the trailer.
Turn on the hazard warning lights,
and turn the ignition switch to the
LOCK (0) position. Have all
passengers get out of the vehicle
while you change the tire.
1.
2.
3.
4.
CONT INUED
Changing a Flat Tire
T aking Care of t he Unexpect ed
219
TOOLS
SPARE TIRE
JACK
The vehicle can easily roll off
the jack, seriously injuring
anyone underneath.
Follow the directions for
changing a tire exactly, and
never get under the vehicle
when it is supported only by the
jack.

Diagnosing why the engine won’t
start falls into two areas, depending
on what you hear when you turn the
ignition switch to the START (III)
position: Wh
en you turn the ignition switch to
the START (III) position, you do not
hear the normal noise of the engine
trying to start. You may hear a
clicking sound, a series of clicks, or
nothing at all. Turn
the ignition switch to the
START (III) position. If the
headlights do not dim, check the
condition of the fuses. If the fuses
areOK,thereisprobably
something wrong with the
electrical circuit for the ignition
switch or starter motor. You will
need a qualified technician to
determine the problem. See
on page .
If the headlights dim noticeably or
go out when you try to start the
engine, either the battery is
discharged or the connections are
corroded. Check the condition of the
battery and terminal connections
(see page ). You can then try
jump starting the vehicle from a
booster battery (see page ).
You
hear nothing, or almost
nothing. The engine’s starter
motor does not operate at all, or
operates very slowly.
You can hear the starter motor
operating normally, or the starter
motor sounds like it is spinning
faster than normal, but the engine
does not start up and run.
Turn the ignition switch to the ON
(II) position. Turn on the
headlights, and check their
brightness. If the headlights are
very dim or do not come on at all,
the battery is discharged (see on page ).
Check the transmission interlock.
If you have a manual transmission,
the clutch pedal must be pushed
all the way to the f loor or the
starter will not operate. With an
automatic transmission, the shif t
lever must be in Park or neutral.
Check these things:
227 227
214 239
CONT INUED
Nothing Happens or the Starter
Motor Operates Very Slowly
Emergency T owing
Jump Starting
If theEngineWon’tStart
T aking Care of t he Unexpect ed
225

Although this seems like a simple
procedure, you should take several
precautions.
You cannot start your vehicle with an
automatic transmission by pushing
or pulling it.The numbers in the illustration show
you the order to connect the jumper
cables.
Turn of f all the electrical
accessories: heater, A/C, audio
system, lights, etc. Put the
transmission in neutral (M/T) or
Park (A/T), and set the parking
brake. Open the hood, and check the
physical condition of the battery.
In very cold weather, check the
condition of the electrolyte. If it
seems slushy or f rozen, do not try
jump starting until it thaws.
1.
2.
CONT INUED
To Jump Start Your Vehicle:
Jump Starting
T aking Care of t he Unexpect ed
227
BOOSTER BATTERY
A battery can explode if you do
not follow the correct procedure,
seriously injuring anyone
nearby.
Keep all sparks, open flames,
and smoking materials away
from the battery.
If a battery sits in extreme cold, the
electrolyte inside can f reeze.
Attempting to jump start with a f rozen
battery can cause it to rupture.

If the indicator comes on repeatedly,
even though it may turn off as you
continue driving, have your vehicle
checked by your dealer as soon as
possible.
If
this indicator comes on
while driving, it means one
of the engine’s emissions control
systems may have a problem. Even
though you may feel no difference in
your vehicle’s performance, it can
reduce your fuel economy and cause
increased emissions. Continued
operation may cause serious damag e.
If you have recently refueled your
vehicle, the indicator coming on
could be due to a loose or missing
fu el fill cap. You will also see a
‘‘CHECK FUEL CAP’’ message on
the information display. Tighten the
cap until it clicks at least once.
Tightening the cap will not turn the
indicator off immediatel y; it can take
several days of normal driving. If
your vehicle has an automatic
transmission, the malfunction
indicator lamp may also come on
with the ‘‘D’’ indicator. Tocheckiftheyareset,turnthe
ignitionswitchtotheON(II)
position,wi
thoutstartingtheengine.
Them alfunctionindicato rlampwill
comeonfo r20seconds.Ifi tthen
goesoff,thereadinesscodesareset.
Ifitblinksfi vetimes,thereadiness
codesarenotset.Ifpossible,donot
take your vehicle for a state
emissions test until the readiness
codes are set. Ref er to for more information
(see page ). If your vehicle’s battery has been
disconnected or gone dead, these
codes are erased. It takes several
days of driving under various
conditions to set the codes again.
Your vehicle has certain " readiness
codes" that are part of the on-board
diagnostics f or the emissions
systems. In some states and
provinces, part of the emissions testing is to make sure these codes
are set. If they are not set, the test
cannot be completed.
254
Malf unction Indicator L amp
Emissions
T esting
R
ea
d ines
sC

odes
232
If you keep driving with the
malf unction indicator lamp on, you can
damage your vehicle’s emissions
controls and engine. Those repairs may
not be covered by your vehicle’s
warranties.

The transmission number is on a
label on top of the transmission. The engine number is stamped into
the engine block.
Identif ication Numbers
Technical Inf ormation
243
AUTOMATIC TRANSMISSION NUMBER
ENGINE NUMBER MANUAL TRANSMISSION NUMBER

Î
Î
Î
Î
Î
ÎÎÎ
Î
ÎÎ
Î
Î
Î
Î
Î Î
ÎÎ
Î
Specif ications
244
Capacities Engine Weights Dimensions 169.3 in (4,300 mm)
1.90 US gal (7.2
)
1.93 US gal (7.3
)
2.6 US qt (2.5
)
7.6 US qt (7.2
)
2.0 US qt (1.9
)
1.35 US gal (5.1
)
2.7 US qt (2.6
)
1.37 US gal (5.2
)
7.4 US qt (7.0
)
1.3 US qt (1.2
)
1.1 US qt (1.0)
2.4 US qt (2.3
)
2.3 US qt (2.2)
Engine
coolant
Automatic
transmission
fluid
Manual
transmission
fluid
Rear
differential
fluid (4WD)
Windshield
washer
reservoir
4.8 US qt (4.5
)
Fuel tank
Engine oil 5.6 US qt (5.3
)
4.2 US qt (4.0)
4.4 US qt (4.2)
15.9 US gal (60
)
0.16 US gal (0.6
)
Including the coolant in the reserve tank and that remaining in the
engine
Reserve tank capacity: Excluding the oil remaining in the engine
Type
BorexStroke
Displacement
Compression ratio
Spark plugs
SKJ20DR-M11 IZFR6K-119.7 : 1
144 cu-in (2,354 cm
)
3.43 x 3.90 in (87.0 x 99.0 mm) Water cooled 4-stroke DOHC
i-VTEC 4-cylinder gasoline engine
See the certification label attached
to the driver’s doorjamb (front
edge of rear door).
Gross vehicle weight rating 62.5 in (1,587 mm) 62.3 in (1,582 mm)
62.1 in (1,578 mm)
62.1 in (1,577 mm)
101.4 in (2,575 mm) 70.4 in (1,788 mm) 71.5 in (1,815 mm)
Length
Width
Height
Wheelbase
Track 170.9 in (4,341 mm) 170.3 in (4,326 mm)
69.4 in (1,763 mm)
Approx. 1:
2:
NGK:
DENSO:
Front
Rear
3:
4:
Change
Without filter
Total Change
Total
Change
Total
Change
4WD
2WD
Total 4WD
2WD
Change
Total 4WD
2WD
Change
Total
LX model
EX model
SC model
5:
Automatic Transmission
Manual Transmission
4 1, 2
3
1, 2
3
1
5
5
3 2
1, 2
3
Including filter

The PGM-FI system uses sequential
multiport f uel injection. It has three
subsystems: air intake, engine
control, and f uel control. The
powertrain control module (PCM) in
automatic transmission vehicles or
the engine control module (ECM) in
manual transmission vehicles uses
various sensors to determine how
much air is going into the engine. It
then controls how much f uel to inject
under all operating conditions.The emissions control systems are
designed and certif ied to work to-
gether in reducing emissions to
levels that comply with the Clean Air
Act. To make sure the emissions
remain low, you should use only new
Honda replacement parts or their
equivalent f or repairs. Using lower
qualitypartsmayincreasethe
emissions f rom your vehicle.
The exhaust emissions controls
include three systems: PGM-FI,
ignition timing control, and three
way catalytic converter. These three
systems work together to control the
engine’s combustion and minimize
the amount of HC, CO, and NOx that
comes out the tailpipe. The exhaust
emissions control systems are
separate f rom the crankcase and
evaporative emissions control
systems. The emissions control systems are
covered by warranties separate from
the rest of your vehicle. Read your
warranty manual for more informa-
tion.
The three way catalytic converter is
in the exhaust system. Through
chemical reactions, it converts HC,
CO, and NOx in the engine’s exhaust
to carbon dioxide (CO ), nitrogen
(N ), and water vapor. This system constantly adjusts the
ignition timing, reducing the amount
of HC, CO, and NOx produced.
2
2
Exhaust Emissions Controls Replacement PartsPGM-FI System
Three Way Catalytic Converter
Ignit ion T iming Cont rol Syst em
Emissions Cont rols
252

Without touching the accelerator
pedal, start the engine, and let it
idle f or 20 seconds.
If you take your vehicle f or an
emissions test shortly af ter the
battery has been disconnected or
gone dead, it may not pass the test.
This is because of certain " readiness
codes" that must be set in the on-
board diagnostics f or the emissions
systems. These codes are erased
when the battery is disconnected,
and set again only after several days
of driving under a variety of
conditions. If the testing f acility determines that
the readiness codes are not set, you
will be requested to return at a later
date to complete the test. If you must
get the vehicle retested within the
next two or three days, you can
condition the vehicle f or retesting by
doing the f ollowing.
Make sure the f uel tank is nearly,
but not completely f ull (around
3/4). Keep the vehicle in Park
(automatic transmission) or
neutral (manual transmission).
Increase the engine speed to 2,000
rpm,andholditthereuntilthe
temperature gauge rises to at least
1/4of thescale(about3minutes).
Make sure the vehicle has been
parked with the engine of f f or 6
hours or more.
Make sure the ambient
temperature is between 40° and
95°F. Without touching the accelerator
pedal, start the engine, and let it
idle f or 20 seconds.
T esting of Readiness Codes
Emissions T esting
254

CONT INUED
....................................
Accessories .143
ACCESSORY (Ignition Key
.......................................
Position) .79
..............
Accessory Power Sockets .97
....................
Additives, Engine Oil .190
.........
Advice f or Pregnant Women .18
.............................
Airbag (SRS) . 11, 24
...
Airbags, Additional Information .24
...
Additional Safety Precautions .36
.............................
Airbag Service .35
How the Passenger Airbag Of f
......................
Indicator Works .34
How the Side Airbag Of f ......................
Indicator Works .34
..
How the SRS Indicator Works .33
How Your Front Airbags
.........................................
Work .27
...
How Your Side Airbags Work .31
How Your Side Curtain Airbags
.........................................
Work .32
........................
SRS Components .24
..............
Air Conditioning System .102
.........................................
Usage .103
.......................
Air Pressure, Tires .209 ......................................
Alignment .245
......................................
Antif reeze .192
Anti-lock Brakes (ABS)
...............................
Indicator . 61, 162
...................................
Operation .161
..............
Anti-thef t, Audio System . 129
.
Anti-thef t Steering Column Lock . 79
......................
Armrests, Front Seat .84
................................
Audio System .107
...
Automatic Seat Belt Tensioners . 22
.............
Automatic Speed Control . 133
..............
Automatic Transmission . 155
..........................
Capacity, Fluid .244
...............
Checking Fluid Level . 194
.......................................
Shif ting .155
.
Shif t Lever Position Indicator . 155
................
Shif t Lever Positions . 155
....................
Shif t Lock Release . 158
......................
Auxiliary Input Jack .125
Battery Charging System ...........................
Indicator . 60, 231
............................
Jump Starting .227 ..............................
Maintenance .214
............................
Specif ications .245
..............................
Bef ore Driving .137
..................................
Belts, Seat . 10, 20
...........................
Beverage Holders .97
...................................
Body Panels .197
..................................
Booster Seats .52
Brakes ...........
Anti-lock System (ABS) . 161
.............
Break-in, New Linings . 138
....................
Bulb Replacement . 203
...........................................
Fluid .196
.........................................
Parking .93
.................
System Indicator . 60, 233
........................
Wear Indicators .161
.............................
Braking System .160
.................
Break-in, New Vehicle . 138
..
Brightness Control, Instruments . 72
........................
Brights, Headlights .72
Index
A
B
INDEX
I