key HONDA FIT 2008 1.G User Guide

µµ
µ Press this button once
to unlock the driver’s door. Push it
twice to unlock the remaining doors
and the tailgate. Some exterior lights
will f lash twice each time you press
the button.
The ceiling light (if the ceiling light
switch is in the door activated
position) will come on when you
press the UNLOCK button. If you do
not open any door or the tailgate
within 30 seconds, the light f ades out.
If you relock the doors and the
tailgate with the remote transmitter
bef ore 30 seconds have elapsed, the
light will go of f immediately.
If you do not open any door or the
tailgate within 30 seconds, they will
automatically relock and the security
system will set. Pressthisbuttonfor
about 2 seconds to attract attention:
the horn will sound, and the exterior
lights will f lash f or about 30 seconds.
To cancel panic mode, press any
other button on the remote
transmitter, or turn the ignition
switch to the ON (II) position.
Press this button once to
lock all doors and the tailgate. Some
exterior lights will f lash once. When
you push LOCK twice within 5
seconds, the horn will sound to
verify that the doors and the tailgate
arelockedandthesecuritysystem
has set. You cannot lock the doors
and the tailgate if any door or the
tailgate is not f ully closed or the key
is in the ignition switch.
CONT INUED
On Sport model
UNL OCK PA NIC
LOCK
Remote Transmitter
Inst rument s and Cont rols
83
LED
UNLOCK
BUTTON LOCK
BUTTON
PANIC
BUTTON
\f—\f—y\f
y
(
\fy\f\fy
2008 Fit

´
As required by the FCC:This device complies with Part 15 of theFCC rules. Operation is subject to thef ollowing two conditions: (1) This devicemay not cause harmf ul interf erence, and(2) this device must accept anyinterf erence received, includinginterf erence that may cause undesiredoperation.
Changes or modif ications not expresslyapproved by the party responsible f orcompliance could void the user’sauthority to operate the equipment.
This device complies with IndustryCanada Standard RSS-210.Operation is subject to the f ollowing twoconditions: (1) this device may not causeinterf erence, and (2) this device mustaccept any interf erence that may causeundesired operation of the device.Remove the old battery, and insert
a new battery into the back of the
cover with the side f acing down.
An improperly disposed of battery
can hurt the environment.
Always conf irm local regulations
for battery disposal.
Install the parts in reverse order.
Separate the transmitter by prying
its middle seam with your
f ingernail.
Inside the transmitter, separate
the inner cover f rom the keypad
by releasing the two tabs on the
cover. 5.
4.
2.
3.
Remote Transmitter
Inst rument s and Cont rols
85
TAB BATTERY
\f—\f—y\fy
(
\fy\f\f\fy
2008 Fit

The ceiling light has a three-position
switch; ON, Door Activated, and
OFF. In the Door Activated (center)
position, the light comes on when
you:Open any door.
Unlock the doors and the tailgate
with the key or the remote
transmitter (if equipped). After all doors are closed tightly, the
light f ades out in about 30 seconds.
The ceiling light (with the switch in
the door activated position) comes
on when you remove the key f rom
the ignition switch. If you do not
open a door, the light f ades out in
about 30 seconds.
To use the accessory power socket,
pull up the cover. The ignition switch
must be in the ACCESSORY (I) or
ON (II) position.
It will not power an automotive type
cigarette lighter element.
To use the sun visor, pull it down.
Whenusingthesunvisorforthe
side window, remove the support rod
f rom the clip, and swing it out.
This socket is intended to supply
power f or 12 volt DC accessories
that are rated 120 watts or less (10
amps).
If you leave any door open without
the key in the ignition switch, the
ceiling light will go of f af ter 3
minutes.
Ceiling L ight
A ccessory Power Socket
Sun Visor
Interior Convenience Items, Interior L ights
Inst rument s and Cont rols
99
DOOR ACTIVATED
OFF ON
\f—\f—y\fy
(
\fy\f
\fy
2008 Fit

Once the security system is set,
opening any door, the tailgate, or the
hood without using the key or the
remote transmitter, will cause it to
alarm. It also alarms if the radio is
removed f rom the dashboard or the
wiring is cut.The security system will not set if
the hood, tailgate, or any door is not
f ully closed. If the system will not set,
check the door and tailgate open
indicator on the instrument panel
(see page ) to see if the doors and
tailgatearefullyclosed.Sinceitis
notpartofthemonitordisplay,
manually check the hood.
To see if the system is set
af ter you exit the vehicle, press the
LOCK button on the remote
transmitter within 5 seconds. If the
system is set, the horn will beep
once.
Do not attempt to alter this system
or add other devices to it.
The security system helps to protect
your vehicle and valuables f rom thef t.
The horn sounds and a combination
of headlights, position lights, side
marker lights and taillights f lashes if
someone attempts to break into your
vehicle or remove the audio unit.
This alarm continues f or 2 minutes,
then the system resets. To reset an
alarming system before the 2
minutes have elapsed, unlock the
driver’s door with the key or the
remote transmitter.
The alarm will also be activated if
the passenger inside the locked
vehicle turns the ignition switch on.
The security system automatically
sets 15 seconds after you lock the
doors, hood, and the tailgate. For the
system to activate, you must lock the
doorsandthetailgatefromthe
outside with the key, driver’s lock
tab, door lock master switch, or
remote transmitter. The security
system indicator on the instrument
panel starts blinking immediately to
show you the system is setting itself . 62
On Sport model
Security System
130
NOTE:SECURITY SYSTEM
INDICATOR
\f—\f—y\f
y
(
\fy\f
y
2008 Fit

Apply the parking brake.
In cold weather, turn of f all
electrical accessories to reduce
the drain on the battery.Without touching the accelerator
pedal, turn the ignition key to the
START (III) position. Do not hold
the key in the START (III)
position f or more than 15 seconds
at a time. If the engine does not
start right away, pause for at least
10 seconds bef ore trying again.
Make sure the shif t lever is in
Park. Press on the brake pedal.
Press the clutch pedal down all the
way. The START (III) position
does not f unction unless the clutch
pedal is pressed.
If the engine does not start within
15 seconds, or starts but stalls
right away, repeat step 4 with the
accelerator pedal pressed halfway
down. If the engine starts, release
pressure on the accelerator pedal
so the engine does not race.If the engine fails to start, press
the accelerator pedal all the way
down, and hold it there while
starting to clear flooding. If the
engine still does not start, return
to step 5.
1.
2.
3. 4.
5.6.
Manual transmission:
Automatic transmission:
Starting the Engine
154
T he immobilizer system protects your
vehicle f rom thef t. If an improperly-
coded key (or other device) is used, the
engine’s f uel system is disabled. For
more inf ormation, see page . The engine is harder to start in cold
weather. Also, the thinner air f ound at
altitudes above 8,000 f eet (2,400
meters) adds to this problem.
77
\f—\f—y\fy
(
\fy\f
y
2008 Fit

µThis position mechani-
cally locks the transmission. Use
Park whenever you are turning of f or
starting the engine. To shif t out of
Park, you must press on the brake
pedal and have your f oot of f the
accelerator pedal. Press the release
buttononthefrontof theshiftlever
to move it.
If you have done all of the above and
still cannot move the lever out of
Park, see on
page .
To avoid transmission damage, come
to a complete stop bef ore shif ting
into Park. You must also press the
release button to shift into Park. The
shif t lever must be in Park bef ore
you can remove the key f rom the
ignition switch. 161To shift from:
PtoR
RtoP
NtoR DtoS
StoD
DtoN
NtoD RtoN Do this:
Press the brake pedal, and
press the shift lever release
button.
Press the shift lever release
button.
Move the shift lever.
Do this:
Press the brake pedal, and
press the shift lever release
button.
Press the shift lever release
button.
Move the shift lever.
To shift from:
PtoR
RtoP
NtoR
Dto2 2to1
1to2
2toD
DtoD DtoN
DtoD NtoDRtoN
3
3
3
3
All models except Sport Sport modelPark (P)
Shif t L ock Release
Automatic Transmission
158
\f—\f—y\fy
(
\fy\f
y
2008 Fit

This allows you to move the shif t
lever out of Park if the normal
method of pushing on the brake
pedal and pressing the release
button does not work.Set the parking brake.
Remove the key from the ignition
switch.
Push down on the key while you
pressthereleasebuttononthe
shif t lever and move the shif t lever
out of Park to neutral.
Insert the key in the shift lock
release slot.Remove the key from the shift
lock release slot, then reinstall the
cover. Make sure the notch on the
cover is on the lef t side. Press the
brake pedal, and restart the engine.
If you need to use the shif t lock
release, it means your vehicle is
developing a problem. Have it
checked by your dealer.
Putaclothonthenotchof the
shif t lock release slot cover. Using
a small f lat-tipped screwdriver or a
metal f ingernail f ile, caref ully pry
on the notch of the cover to
remove it.
1.
2.
3.
4.
5.6.
Shif t L ock Release
Automatic Transmission
Driving
161
COVER
RELEASE
BUTTON
SHIFT LOCK RELEASE SLOT
NOTCH
\f—\f—y\f
y
(
\fy\f
y
2008 Fit

Turn the ignition switch to the
START (III) position. If the
headlights do not dim, check the
condition of the f uses. If the f uses
areOK,thereisprobably
something wrong with the
electrical circuit for the ignition
switch or starter motor. You will
need a qualif ied technician to
determine the problem. Seeon page .
If the headlights dim noticeably or
go out when you try to start the
engine, either the battery is
discharged or the connections are
corroded. Check the condition of the
battery and terminal connections
(see page ). You can then try
jump starting the vehicle from a
booster battery (see page ). In this case, the starter motor’s
speed sounds normal, or even f aster
than normal, when you turn the
ignition switch to the START (III)
position, but the engine does not run.
Are you using the proper starting
procedure? Ref er to on page .
Are you using a properly coded
key? An improperly coded key will
cause the immobilizer system
indicator in the instrument panel
to blink rapidly (see page ). Do you have f uel? Check the f uel
gauge; the low f uel indicator may
not be working.
There may be an electrical
problem, such as no power to the
f uel pump. Check all the f uses
(see page ).
If youfindnothingwrong,youwill
need a qualif ied technician to f ind
the problem. See on page .
154 77
238
214 226 233
238
If theEngineWon’tStart
Emergency T owing T he Starter Operates Normally
Starting the
Engine Emergency
Towing
T aking Care of t he Unexpect ed
225
\f—\f—y\fy
(
\fy\f\fy
2008 Fit

CONT INUED
....................................
Accessories .144
ACCESSORY (Ignition Key
.......................................
Position) .78
...............
Accessory Power Socket .99
....................
Additives, Engine Oil .188
.......
Adjusting the Steering Wheel .75
...........................
Advanced Airbags .27
...............................
Airbag (SRS) .9,22
..............
Air Conditioning System .102
.........................................
Usage .103
.......................
Air Pressure, Tires .210
.......................
Alcohol in Gasoline .136
......................................
Antif reeze .190
Anti-lock Brakes (ABS)
...............................
Indicator .62,168
...................................
Operation .168
..............
Anti-thef t, Audio System .128
.
Anti-thef t Steering Column Lock .78
................................
Audio System .107
...
Automatic Seat Belt Tensioners .20
.............
Automatic Speed Control .131
..............
Automatic Transmission .157
..........................
Capacity, Fluid .244
...............
Checking Fluid Level .193 ..........................
Paddle Shif ters .162
.......................................
Shif ting .157
Shif t Lever Position
...............................
Indicators .157
................
Shif t Lever Positions .158
....................
Shif t Lock Release .161
......................
Auxiliary Input Jack .127
............................
Capacities Chart .244
.............
Carbon Monoxide Hazard .53
Battery
Charging System ...........................
Indicator .60,230
............................
Jump Starting .226
..............................
Maintenance .214
............................
Specif ications .245
..............................
Bef ore Driving .135
....................................
Belts,Seat.8,18
...........................
Beverage Holders .98
..................................
Booster Seats .50
Brakes
...........
Anti-lock System (ABS) .168
.............
Break-in, New Linings .136
....................
Bulb Replacement .201
...........................................
Fluid .195
.........................................
Parking .96 .................
System Indicator .60,232
..........................
System Design .167
........................
Wear Indicators .167
.............................
Braking System .167
.................
Break-in, New Vehicle .136
..
Brightness Control, Instruments .74
..................
Brights, Headlights .72,73
Bulb Replacement
..........................
Back-up Lights .201
..............................
Brake Lights .201
Front Parking Lights/
...
Front Side Marker Lights .198
.................................
Fog Lights .199
.................................
Headlights .196
.........
High-mount Brake Light .202
............................
Specif ications .245
....................................
Taillights .201
............
Turn Signal Lights .198,201
..............................
Bulbs, Halogen .196
Index
A
B
C
INDEX
I
\f—\f—y\f\fy
(
\fy\fy
2008 Fit

ÎÎ
...............
Gas Mileage, Improving .141
..........................................
Gasohol .136
.........................................
Gasoline .136
.....................
Low Fuel Indicator .62
...........................................
Gauge .68
................
Octane Requirement .136
........................
Tank, Ref ueling .137
................
Gas Station Procedures .137
Gauges
...............................................
Fuel .68
Gearshif t Lever Positions ..........
Automatic Transmission .158
..............
Manual Transmission .155 ........................................
Glove Box .98
Gross Vehicle Weight Rating
.....................................
(GVWR) .148
.................................................
Fuel .136
..........
Check Fuel Cap Indicator .68
......................
Fill Door and Cap .137
.....................
Low Fuel Indicator .62
...........................................
Gauge .68
................
Octane Requirement .136
...............................
Oxygenated .136
........................
Tank, Ref ueling .137
...............................
Fuel Economy .141
.....................
Fuses, Checking the .234 .............
Halogen Headlight Bulbs .196
..............
Hazard Warning Flashers .74
Headlights
........................................
Aiming .196
.......
Daytime Running Lights .73
..................
High Beam Indicator .65
.........................
Reminder Chime .73
........
Replacing Halogen Bulbs .196
...................................
Turning on .73
..............................
Head Restraints .87
.....................
Heating and Cooling .102
............................
High Beam Lever .73
.......................
Hood, Opening the .138
..............................................
Horn.4,70
...........................
Hydraulic Clutch .195
...
Identif ication Number, Vehicle .242 Ignition
..............................................
Keys .76
...........................................
Switch .78
............
Timing Control System .252
........................
Immobilizer System .77
.........
Important Safety Precautions .6
Index
G H
I
IV
\f—\f—y\f\fy
(
\fy\f
y
2008 Fit