ABS HONDA INSIGHT 2001 1.G User Guide

Remove the blade f rom its holder
by grasping the tabbed end of the
blade. Pull f irmly until the tabs
come out of the holder.Examine the new wiper blades. If
they have no plastic or metal rein-
f orcement along the back edge,
remove the metal reinf orcement
strips f rom the old wiper blade and
install them in the slots along the
edge of the new blade.Slide the new wiper blade into the
holder until the tabs lock.
Slide the wiper blade assembly
onto the wiper arm. Make sure it
locks in place.
Lower the wiper arm down against
the windshield.
3. 4. 5. 6. 7.
Wiper Blades
Maint enance
188
BBLLAADDEEBBLLAADDEE
RREEIINNFFOORRCCEEMMEENNTT

CONT INUED
Unclip the end of the hold-down
wire f rom its slot. Pivot it out of
the way and remove the bulb.
Insert the new bulb into the hole,
making sure the tabs are in their
slots. Pivot the hold-down wire
back in place and clip the end into
the slot.
Install the rubber seal over the
back of the headlight assembly.
Make sure it is right side up; it is
marked ‘‘TOP.’’
Push the electrical connector onto
the tabs of the new bulb. Make
sure it locks in place.
Turn on the headlights to test the
new bulb.
Reinstall the radiator reserve tank.Remove the socket from the
headlight assembly by turning it
one-quarter turn counterclockwise.
Pull the bulb straight out of its
socket.
Install the new bulb into the
socket.Insert the socket back into the
headlight assembly. Turn it
clockwise to lock it in place.
Testthelightstomakesurethe
new bulb is working.
If you are changing the bulb on
the driver’s side, start the engine,
turn the steering wheel all the way
to the right, and turn off the
engine. If you are changing the
bulb on the passenger’s side, turn
the steering wheel to the left.
4. 5. 6. 7. 8.
1.
1. 2. 3. 4. 5.
Lights
Maint enance
Replacing the Front Parking
Lights
Replacing the Front Side Marker/
Turn Signal and Parking L ightBulb
201

Removethelensbycarefully
prying on the edge of the lens in
the middle with a f ingernail f ile or
a small f lat-tip screwdriver. Do not
pry on the edge of the housing
around the lens.
Remove the bulb by pulling it
straight out of its metal tabs.
Push the new bulb into the metal
tabs. Snap the lens back in place.Removethelensbycarefully
prying on the edge of the lens in
the middle with a f ingernail f ile or
a small f lat-tip screwdriver. Do not
pry on the edge of the housing
around the lens.
1. 2. 3. 1.
Lights
Maint enance
Replacing an Interior L ight Bulb Replacing the Cargo A rea L ight
205
IINNTTEERRIIOORRLLIIGGHHTT

ÝÔ
CONT INUED
Tighten the wheel nuts securely in
the same crisscross pattern. Have
the wheel nut torque checked at
the nearest automotive service
f acility.
Tighten the wheel nuts to: Tighten the two stud fasteners.
Do not catch your clothes or
hands on the hooks on the rear
f ender when you replace the
wheel. To install the rear wheel skirt,
place the skirt against the body.
Line up the slots on the skirt with
the tabs in the body, then push the
skirt upward.
Make sure the wheel skirt is
installed correctly.
Alignthe marksonthestud
fastener with the marks on the
wheel skirt.
11. 12. 13.
Changing a Flat T ire
T aking Care of t he Unexpect ed
221
TTAABB
SSLLOOTT
80 lbf·ft (108 N·m , 11 kgf·m) It is not recommended to drive your car
without the wheel skirts.
It will af f ect the f uel consumption.

µµ
No. Amps. Circuits Protected No. Amps. Circuits Protected
1 23456789
10 50 A
80 A
30 A
10 A
15 A
10 A
15 A
15 A
15 A IG1 Main
Battery
ABS Motor
Hazard
IMA
Horn Stop
Fuel Pump
Lef t Headlight
Not used
Right Headlight 1112131415161718192030 A
40 A
30 A
20 A
40 A
30 A
40 A
7.5 A 20 A Cooling Fan
Heater Motor
Rear Defroster
ABS F/S
Power Steering
Back Up, ACC
Power Window
IMA ECU
Condenser Fan
Spare Fuse
Fuses
T aking Care of t he Unexpect ed
237
UNDER-HOOD FUSE BOX