HONDA INSIGHT 2002 1.G Owners Manual

Î
Î
Your Honda’s audio system provides
clear reception on both AM and FM
bands, while the preset buttons allow
you to easily select your f avorite
stations.
The cassette system f eatures Dolby
noise reduction, automatic sensing of
chromium-dioxide (CrO ) tape, and
auto-reverse f or continuous play.
2
Dolby noise reduction manuf actured under
license from Dolby Laboratories Licensing Corpo-
ration. ‘‘DOLBY’’ and the double-D symbol are trademarks of Dolby Laboratories
Licensing Corporation.
A M/FM/Cassette Stereo A udio
System
Audio System
Comf ort and Convenience Feat ures98

µµ
Û
Ý
You can use any of f our methods to
f ind radio stations on the selected
band: TUNE, SEEK, SCAN or the
Preset buttons.
Use the TUNE bar to tune
the radio to a desired f requency.
Press the upper part ( ) to tune
toahigherfrequency,orthelower
part ( ) to tune to a lower
f requency. The f requency numbers
will start to change rapidly. Release
the bar when the display reaches the
desired f requency. To change the
f requency in small increments, press
and release the TUNE bar quickly. The SEEK f unction
searches the band for a station with
a strong signal. To activate it, push
the SEEK switch up or down, then
release it. Depending on which way
you push the switch, the system
scans upward or downward f rom the
current f requency. It stops when it
finds a station with a strong signal.
The ignition switch must be in
ACCESSORY (I) or ON (II) to
operate the audio system. Turn the
system on by pushing the PWR/
VOL knob.
Adjust the volume by turning the
PWR/VOL knob.
The band and f requency that the
radio was last tuned to is displayed.
To change bands, press the AM/FM
button. On the FM band, ST will be
displayed if the station is broadcast-
ing in stereo. Stereo reproduction on
AM is not available.
CONT INUED
Operating the Radio
TUNESEEK
Audio System
Comf ort and Convenience Feat ures99

µThe SCAN f unction
samples all the stations with strong
signals on the selected band. To
activate it, press the SCAN button,
then release it. When the system is
intheSCANmode,SCNshowsin
the display. The system will scan up
the band for a station with a strong
signal. When it f inds one, it will stop
and play that station for
approximately f ive seconds. If you do
nothing, the system will then scan
f or the next strong station and play
that f or f ive seconds. When it plays a
station that you want to continue
listening to, press the SCAN button
again. SCAN
Audio System
Comf ort and Convenience Feat ures100
S SC CAA N
N B
BUUT TT
TO
ON N
S
SE EE
EK
K S
SWWI ITT C
CH H
A
A
M
M /
/F
FM M
B
BU UT TT
TO
ON N
P
P W
WR R//V
V O
OL L
K
KN NO OBB T
T
U
UN NEE B
BAA R
R

µ
Repeat steps 1 to 3 to store a total
of six stations on AM and twelve
on FM. Pick the Preset button you want
for that station. Press the button
and hold it until you hear a beep. Use the TUNE or SEEK f unction
to tune the radio to a desired
station. Select the desired band, AM or
FM. FM1 and FM2 let you store
two f requencies with each Preset
button.
To store a f requency:
Once a station’s frequency is stored,
simply press and release the proper
preset button to tune to it.
The preset f requencies will be lost if
your car’s battery goes dead, is
disconnected, or the radio f use is
removed.
You can store the
f requencies of your f avorite radio
stations in the six preset buttons.
Each button will store one f requency
on the AM band, and two
f requencies on the FM band.
1.
2.
3.
4. Preset
Audio System
Comf ort and Convenience Feat ures101
S SE EE
EK
K S
SWWI ITT C
CH H
A
A
M
M /
/F
FM M B
BUUT TT
TO
ON N
P
PR
RE ES
SE ET
T
B
BU UT TT
TO
ON NSS T
T
U
UN NEE B
BAA R
R

µµ
These two
controls adjust the strength of the
sound coming f rom each speaker.
The Balance control adjusts the side-
to-side strength, while the Fader
control adjusts the f ront-to-back
strength.
To adjust the fader, push on the
BASS/FADER control knob to get it
to pop out. Pull it out slightly f arther,
and adjust the f ront-to-back sound to
your liking. Push the knob back in
when you are done so you cannot
change the setting by accidentally
bumping it.
To adjust the balance, push on the
TREBLE/BALANCE control knob
to get it to pop out. Pull it out slightly
f arther, and adjust the side-to-side
sound to your liking. Push the knob
back in when you are done so you
cannot change the setting by
accidentally bumping it. Use these controls
to adjust the tone to your liking.
To adjust the Treble level, push on
the TREBLE/BALANCE control
knob to get it to pop out. Without
pulling it out f arther, turn the knob
to adjust the treble level. Push the
knob back in when you are done so
you cannot change the setting by
accidentally bumping it. To adjust the Bass level, push on the
BASS/FADER control knob to get it
to pop out. Without pulling it out
f arther, turn the knob to adjust the
bass level. Push the knob back in
when you are done so you cannot
change the setting by accidentally
bumping it.
Adjusting the Sound
Balance/Fader
Treble/Bass
Audio System
Comf ort and Convenience Feat ures102
T TR
RE EB
BL LEE /
/B
BA A L
LAA N
NC CEE
C
CO ON NTTR
RO OL L
B
BA
A S
SSS//F
FA A D
DE
ER
R
C
CO ON NTTR
RO OL L

For inf ormation, See page .To set the time, press the CLOCK
(TAPE/CD) button for more than
twoseconds.Tosetthehours,press
the H (Preset 4) button. The hour
numbers will begin blinking. Keep
pressing the button until the
numbers advance to the desired time.To set the minutes, press the M
(Preset 5) button. The minutes
numbers will begin blinking. Keep
pressing the button until the
numbers advance to the desired time.
You can use the instrument panel
brightness control buttons to adjust
the illumination of the audio system
(see page ). The audio system
illuminates when the parking lights
are on, even if the radio is turned of f .
The audio system usually shows the
time when the ignition switch is in
ACCESSORY (I) or ON (II). It
shows the operation mode of the
radio, cassette player, or optional CD
changer when you operate them,
then goes back to the time display
af ter f ive seconds.
If an error occurs while operating
the optional CD changer, the display
will keep showing the error code and
will not switch to the time display
until the error is corrected. 112
62
CONT INUED
Radio Frequencies and Reception
A udio System L ighting
Digital Clock
Audio System
Comf ort and Convenience Feat ures103
C CL LOOC CKK B
BUUT TT
TO
ON N
M
MB
BUUT TT
TO
ON NR
RE
ES
SE ET
T B
BUUT TT
TO
ON N
H
H B
BUUT TT
TO
ON N

Û
For example:
1:06 would RESET to 1:00
1:52 would RESET to 2:00
You can use the RESET (Preset 6)
button to quickly set the time to the
nearest hour. If the displayed time is
bef ore the half hour, pressing
RESETsetstheclockbacktothe
previous hour. If the displayed time
is af ter the half hour, pressing
RESET sets the clock f orward to the
beginning of the next hour.
The tape direction indicator will light
to show you which side of the
cassette is playing. The indicates
thesideyouinsertedfacingupward
is now playing. If you want to play
the other side, press the PROG
button.
Turn the audio system ON. Make
sure the tape opening on the cassette
is f acing to the right, then insert the
cassette most of the way into the slot.
The system will pull it in the rest of
the way, and begin to play.
The blinking stops and the time is
set when you press any buttons
other than the time setting buttons
(Presets 4, 5 and 6).
Operating the Cassette Player
Audio System
Comf ort and Convenience Feat ures104
S SK
KIIPP
B
BU UT TT
TO
ON N F
FF
F B
BUUT TT
TO
ON N
E
E
J
JEE C
CT T
B
BU UT TT
TO
ON N T
T
A
A P
PE
E D
DI
IRRE EC
CT TI
IOON N I
INND DI
ICCA A T
TO
OR R
C
CA A S
SSSEET
TT
TE
E
S
SL LOOT T
R
RE
EW
W B
BUUT TT
TO
ON N
R
RP PT
T
B
BU UT TT
TO
ON N
D
DO
OL LBBY Y B
BUUT TT
TO
ON N
P
P L
LAA Y
Y B
BUUT TT
TO
ON N
P
P
R
RO OG G B
BUUT TT
TO
ON N

µ
µ The Skip Function allows
you to f ind the beginning of a song
or passage. To f ind the beginning of
the song or passage currently
playing, push the SKIP switch down.
You will see REW f lashing in the
display as the tape rewinds. To f ind
the beginning of the next song, push
the SKIP switch up. You will see FF
flashing in the display as the tape
f ast f orwards. When the system
f inds the beginning of a song or
passage, it goes back to PLAY mode.
With a cassette playing, you can use
the FF, REW, SKIP, or REPEAT
f unction to f ind a desired program.
Fast Forward and Re-
wind move the tape rapidly. To re-
wind the tape, push the REW button.
You will see REW in the display. To
fast forward the tape, push the FF
button. You will see FF displayed.
Press the PLAY button to take the
system out of rewind or f ast f orward.
If the system reaches the end of the
tape while in f ast f orward or rewind,
it automatically stops that function,
reverses direction, and begins to play.
When the system reaches the end of
the tape, it will automatically reverse
direction and play the other side. If
you want to remove the cassette
f rom the drive, press the EJECT
button. Dolby noise reduction turns on when
you insert a cassette. If the tape was
not recorded with Dolby noise reduc-
tion, turn it of f by pressing the
button.
CONT INUED
SK IP
T ape Search Functions
FF/REW
Audio System
Comf ort and Convenience Feat ures105

µThe Repeat f unction
continuously replays the current
song or passage. Press the RPT
button to activate it; you will see RPT
displayed as a reminder. When the
system reaches the end of the song
or passage currently playing, it will
automatically go into rewind. When
it senses the beginning of the same
song or passage, the system returns
to PLAY mode. It will continue to
repeat this same program until you
deactivate REPEAT by pressing the
button again. REPEAT
Audio System
Comf ort and Convenience Feat ures106
F FF F
B
BU UT TT
TO
ON N
E
E
J
JEE C
CT T B
BUUT TT
TO
ON N
P
PL
LAA Y
Y B
BUUT TT
TO
ON N
D
D O
OL LBBY Y B
BUUT TT
TO
ON N
S
SK KIIPP B
BUUT TT
TO
ON N C
CA
A S
SSSEET
TT
TE
E S
SLLOOT T
P
P R
RO OG G B
BUUT TT
TO
ON N T
T
A
A P
PE
E D
DI
IRRE EC
CT TI
IOON N
I
IN ND DI
ICCA A T
TO
OR R
R
RP PT
T B
BUUT TT
TO
ON N R
REEW
W
B
BU UT TT
TO
ON N R
RE
EP
PE
EA
A T
T
I
IN ND DI
ICCA A T
TO
OR R

Damaged cassettes can jam inside
the drive or cause other problems.
See page for information on
cassette care and protection. The SKIP and REPEAT f unctions
use silent periods on the tape to f ind
the end of a song or passage. These
f eatures may not work to your
satisfaction if there is almost no gap
between selections, a high noise
level between selections, or a silent
period in the middle of a selection.115
Caring f or Cassettes
Audio System
Comf ort and Convenience Feat ures107
T T
A
A P
PE
E D
DI
IRRE EC
CT TI
IOON N
I
IN ND DI
ICCA A T
TO
OR R
S
SK KIIPP B
BUUT TT
TO
ON N
E
E
J
JEE C
CT T B
BUUT TT
TO
ON N C
CAA S
SSSEET
TT
TE
E S
SLLOOT T
R
RE EW
W
B
BU UT TT
TO
ON N
R
RP
PT
T B
BUUT TT
TO
ON N F
FFF
B
BU UT TT
TO
ON N
P
P L
LAA Y
Y B
BUUT TT
TO
ON N
P
P R
RO OG G B
BUUT TT
TO
ON N
D
D O
OL LBBY Y B
BUUT TT
TO
ON N