width HONDA INSIGHT 2005 1.G Owners Manual

ÎÎÎ
Î
Î
Î
Î
Î
Specif ications
194
Dimensions
Weights
EngineCapacities
66.7 in (1,695 mm)
53.3 in (1,355 mm)
94.5 in (2,400 mm)
56.5 in (1,435 mm)
52.2 in (1,325 mm) 10.6 US gal (40
)
155.0 in (3,938 mm)
0.61 US gal (2.3)
ILZFR5A-11 10.3 : 1 10.8 : 1
60.8 cu-in (995 cm
)
2.8x3.21in(72x81.5mm)
0.11 US gal (0.4
)
4.8 US qt (4.5
)
5.8 US qt (5.5)
3.5 US qt (3.3)
1.7 US qt (1.6
)
1.6 US qt (1.5)
3.2 US qt (3.0
)
2.4 US qt (2.3)
2.6 US qt (2.5)
Length
Width
Height
Wheelbase
Track
Gross vehicle weight rating
Type
BorexStroke
Displacement
Compression ratio
Spark plugs Fuel tank
Engine
coolant
Engine oil
Manual transmission
fluid
Automatic transmission
fluid (CVT)
Windshield washer reservoir
Including the coolant in the reserve tank and that remaining in the
engine.
Reserve tank capacity:
See the certification label attached
to the driver’s doorjamb.
Water cooled 4-strokeSOHC VTEC in line
3-cylinder gasoline engine 1.06 US gal (4.0
)
1.03 US gal (3.9)
Contact your Honda dealer when replacement is necessary. Front
Rear
Approx.
U.S. model
M/T
CVT
1: 2:
3:M/T
CVT
Change
Total
Change
Without filter
Total
Change
Total
Change
Total
4 : Excluding the oil remaining in the engine.
1 32
4
Including filter

µ
The tires on your vehicle meet all
U.S. Federal Saf ety Requirements.
All tires are also graded f or
treadwear, traction, and temperature
perf ormance according to
Department of Transportation
(DOT) standards. The f ollowing
explains these gradings.
Quality grades can be f ound where
applicable on the tire sidewall
between the tread shoulder and the
maximum section width. For
example:
All passenger car tires must conf orm
to Federal Saf ety Requirements in
addition to these grades. The treadwear grade is a compara-
tive rating based on the wear rate of
the tire when tested under controlled
conditions on a specif ied government
test course. For example, a tire
graded 150 would wear one and one-
half (1 1/2) times as well on the
government course as a tire graded
100. The relative perf ormance of
tires depends upon the actual condi-
tions of their use, however, and may
depart signif icantly f rom the norm
due to variations in driving habits,
service practices, and dif f erences in
road characteristics and climate.
The traction grades, f rom highest to
lowest, are AA, A, B, and C. Those
grades represent the tire’s ability to
stop on wet pavement as measured
under controlled conditions on
specif ied government test surf aces
of asphalt and concrete. A tire
marked C may have poor traction
perf ormance.
Warning: The traction grade
assignedtothistireisbasedon
straight-ahead braking traction tests,
and does not include acceleration,
cornering, hydroplaning, or peak
traction characteristics.
DOT T ire Quality Grading (U.S. Vehicles)
Unif orm T ire Quality Grading
T readwear 200
Traction AA
Temperature A Treadwear
Traction AA, A, B, C
196

µ
µ
µ
µµ
µ
µ
µµ
µ µ
The tires that came on your vehicle
have a number of markings. Those
you should be aware of are described
below. Rim diameter in inches.
Load index (a numerical code
associated with the maximum
load the tire can carry).
Speed symbol (an
alphabetical code indicating
the maximum speed rating).
Tire Identif ication Number (TIN) is
a group of numbers and letters that
look like the f ollowing example TIN.
This indicates that the tire
meets all requirements of
the U.S. Department of
Transportation.Manuf acturer’s
identification mark.
Tire type code. Date of manufacture.
Whenever tires are replaced, they
should be replaced with tires of the
same size. The f ollowing is an
exampleof tiresizewithan
explanation of what each component
means.
Tire construction code (R
indicates radial). Aspect ratio (the tire’s section
height as a percentage of its
width). Tire width in millimeters. Vehicletype(Pindicates
passenger vehicle).
P
R DOT
B97R
FW6X2202
165
65 14
78
S
Tire Labeling
Tire Size
T ire Ident if icat ion Number
198
DOT B97R FW6X 2202
P165/65R14 78S