climate control HONDA INSIGHT 2013 2.G User Guide

CONT INUED
This button turns the air
conditioningonandoff.Youwillsee
A/C ON or A/C OFF in the display.
When you turn the A/C of f , the
system cannot regulate the inside
temperature if you set the
temperature control below the
outside temperature.Pushing this button also turns the
power mirror heaters on and of f .
When the recirculation indicator is
on, air f rom the vehicle’s interior is
sent throughout the system again.
Select recirculation mode when
driving through dusty or smoky
conditions, then return to fresh
air mode.
The outside air intakes f or the
climate control system are at the
base of the windshield. Keep this
area clear of leaves and other debris.
When the f resh air indicator is on,
air is brought in f rom the outside of
the vehicle.
Thesystemshouldbeleftinfresh
air mode under almost all conditions.
Keeping the system in recirculation
mode, particularly with the A/C of f ,
can cause the windows to fog up. This button turns the rear window
def ogger on and of f (see
page).
126
On U.S. EX models and
all Canadian models
Climate Control System
A ir Condit ioning (A /C) But t on Recirculat ion But t on Rear Window Def ogger But t on
Fresh Air Button
165
12/07/13 16:57:35 31TM8630_170
FeaturesTOC
2013 Insight

To remove f og f rom the inside of the
windows, set as follows:
Use the mode control button to
select the vents the air flows from.
Some air will flow from the
dashboard vents in all modes.
Airf low is divided between
the f loor and corner vents and the
defroster vents at the base of the
windshield. This button directs the main airflow
to the windshield for faster
def rosting. It also overrides any
mode selection you may have made.
Select . The system
automatically switches to fresh air
mode and turns on the A/C.
Adjust the temperature so the
airflow feels warm.
Select to help clear the
rear window.
To increase airf low to the
windshield, close the corner vents.
For f aster def ogging, manually set
the fan speed to high.
For your saf ety, make sure you have
a clear view through all the windows
bef ore driving.
When you select , the system
automatically switches to fresh air
mode and turns on the A/C. For
faster defrosting, manually set the
fan speed to high. You can also
increase airflow to the windshield
by closing the corner vents on
the dashboard.
When you turn of f by
pressing the button again, the
system returns to its former settings.
Air f lows f rom the f loor
vents.
Airf low is divided between
the vents in the dashboard and the
f loor vents.
Air flows from the center
and corner vents in the dashboard. 1.
2.
3.
4.
Climate Control System
Mode Cont rol
Windshield Def rost er But t on
166
12/07/13 16:57:47 31TM8630_171
FeaturesTOC
2013 Insight

To regulate the interior temperature
and humidity, the climate control
system has two sensors. A sunlight
sensor is located in the top of the
dashboard and a temperature/
humidity sensor is next to the
steering column. Do not cover the
sensors or spill any liquid on them.
Climate Control System
Sunlight, T emperature, and
Humidity Sensors
167
TEMPERATURE/HUMIDITY SENSOR
SUNLIGHT SENSOR SUNLIGHT SENSOR
EX models
Insight model and LX model
12/07/13 16:57:53 31TM8630_172
FeaturesTOC
2013 Insight

Î
Î
The f ollowing procedure clears all
leaves and your lif etime points. This
procedure must be f ollowed exactly.
As you progress to a higher level, the
system monitors your driving style
more strictly. As a result, you must
f urther ref ine your driving style to
continue to move up to the next level.
Turn the ignition switch to the ON
(II) position. Conf irm that the ECON
mode is OFF. If it is OFF, proceed to
step 1. Do run the engine.
The following are some of the
conditions that may affect
your score:
Extremely high or low ambient
temperature
Inconsistent acceleration use, such
as pumping the pedal repeatedly
within a short period of time
Frequent use of the climate
control system
Short distance trips If theECONmodeison,pressand
releasetheECONbuttontoturnit
off. You also need to turn the ignition
switch off.
Turn the ignition switch to the ON
Dorun Press and release the brake
pedal at least two times. The
ambient meter color
changes from blue to green .
Complete the following steps within
30 seconds:
The ambient meter color changes only
if the multi- information display’s
meter color change setting is on. (See
page
.)
Press and release the ECON
button two times (ECON mode
comes on, then goes of f ). The
ambient meter color goes of f , and
the accumulated data is cleared.
Turn the ignition switch to the
LOCK (0) position.
:
1.
2.
3.
103
Reset the System
not not
Eco A ssist System
270
12/07/13 17:11:39 31TM8630_275
Bef ore DrivingTOC
ON (II) position again.
the engine.
2013 Insight

The engine coolant temperature
becomes low.
Thepressureonthebrakepedalis
repeatedly applied and released
slightly during a stop.
The ECON button is off, and the
dif f erence between the ambient
temperature and the temperature
setting of the climate control
system becomes signif icant.
Theclimatecontrolsystemstarts
to dehumidif y the interior
The engine automatically
restarts when:
The brake pedal is released.
Under the f ollowing conditions, the
engine restarts even if the brake
pedal is pressed:
The shift position is changed
to R or L.
The accelerator pedal is pressed
The pressure to the brake pedal is
reduced and the vehicle starts
moving while stopped on an incline.
The IMA battery charge
becomes low.
The engine may not stop automatically
under the f ollowing conditions:
The windshield defroster button
is pressed.
TheECONbuttonisoff,andthere
is a signif icant dif f erence between
the ambient temperature and the
temperature setting of the climate
control system.
The climate control system is
dehumidif ying the air.
The vehicle is stopped by braking
suddenly.
When the ECON button is on, the
engine is more likely to stop. See
page f or the ECON button.
127
Auto Idle Stop
282
12/07/13 17:13:10 31TM8630_287
Bef ore DrivingTOC
2013 Insight

If the auto idle stop function turns
of f the engine f or a long time, the
charge of the IMA and 12 volt
batteries becomes low, and the
engine may not restart automatically.
Always turn the ignition switch to
the LOCK (0) position, set the
parking brake, and remove the key if
you are getting out of the vehicle.Thetimethatautoidlestopis
activated may be reduced if you
operate the windshield wipers with
the climate control system on.
This indicator blinks when the auto
idle stop system is in operation. If
the driver’s door is opened while the
indicator is blinking, the buzzer
sounds to notif y that the auto idle
stop system is active. A uto Idle Stop Indicator
Auto Idle Stop
283
AUTO IDLE STOP INDICATOR
12/07/13 17:13:16 31TM8630_288
Bef ore DrivingTOC
2013 Insight

Check the condition of the wiper
blades at least every 6 months.
Replace them if you find signs of
cracking in the rubber, and areas
that are getting hard or if they
leave streaks and unwiped areas
when used.
If you remove a f loor mat, make sure
tore-anchoritwhenyouputitback
in your vehicle.
If you use a non-Honda f loor mat,
make sure it f its properly and that it
canbeusedwiththefloormat
anchors. Do not put additional f loor
mats on top of the anchored mats.
Make sure the rear floor
mats are properly positioned. If
not, the floor mat will interfere
with the seat operation and make
the front passenger’s weight
sensors ineffective. This filter removes the dust and
pollen that is brought in from the
outside through the climate
control system.
Have your dealer replace the filter
when this service is indicated by a
maintenance message on the multi-
inf ormation display. It should be
replaced every 15,000 miles (24,000
km) if you drive primarily in urban
areas that have high concentrations
of soot in the air, or if the f low f rom
theclimatecontrolsystembecomes
less than usual.Wiper Blades
Dust and Pollen Filter
Floor Mats, Dust and Pollen Filter, Wiper Blades
332
12/07/13 17:19:05 31TM8630_337
Maint enanceTOC
2013 Insight

Although this seems like a simple
procedure, you should take several
precautions.To jump start your vehicle:
The numbers in the illustration
show you the order to connect the
jumper cables.
You cannot start your vehicle by
pushing or pulling it. Open the hood, and check the
physical condition of the 12 volt
battery.
Turn of f all the electrical
accessories: climate control, audio
system, lights, etc. Put the
transmission in Park, and set the
parking brake.
1.
2.
Jump Starting
358
BOOSTER
BATTERY
A battery can explode if you do
not follow the correct procedure,
seriously injuring anyone
nearby.
Keep all sparks, open flames,
and smoking materials away
from the battery.
If a battery sits in extreme cold, the
electrolyte inside can f reeze.
Attempting to jump start with a f rozen
battery can cause it to rupture.
12/07/13 17:22:23 31TM8630_363
T aking Care of t he Unexpect edTOC
2013 Insight

Using gloves or a large heavy
cloth, turn the radiator cap
counterclockwise, without
pushing down, to the first stop.
After the pressure releases,
push down on the cap, and turn it
until it comes off.If the temperature stays
normal, check the coolant
level in the radiator reserve
tank. If it has gone down,
add coolant to the MAX mark.
Put the cap back on tightly.
Start the engine, and set the
temperature to maximum heat
(climate control to AUTO at
‘‘ ’’). Add coolant to the
radiator up to the base of the f iller
neck. If you do not have the
proper coolant mixture available,
you can add plain water.
Remember to have the cooling
system drained and ref illed with
the proper mixture as soon as
Put the radiator cap back on
tightly. Run the engine, and check
the high temperature indicator. If
it begins to blink or comes on
again, the engine needs repair
(see
on
8. 9.
10. 11.
If theEngineOverheats
Emergency Towing
362
Removing the radiator cap
while the engine is hot can
cause the coolant to spray out,
seriously scalding you.
Always let the engine and
radiator cool down before
removing the radiator cap.
12/07/13 17:22:50 31TM8630_367
T aking Care of t he Unexpect edTOC
page 374
).
you can.
2013 Insight

Quality grades can be f ound where
applicable on the tire sidewall
between tread shoulder and
maximum section width. For
example:
All passenger car tires must conf orm
to Federal Saf ety Requirements in
addition to these grades.The traction grades, f rom highest to
lowest, are AA, A, B, and C. Those
grades represent the tire’s ability to
stop on wet pavement as measured
under controlled conditions on
specif ied government test surf aces
of asphalt and concrete. A tire
marked C may have poor traction
perf ormance.
Warning:
The traction grade
assignedtothistireisbasedon
straight-ahead braking traction tests,
and does not include acceleration,
cornering, hydroplaning, or peak
traction characteristics.
The tires on your vehicle meet all
U.S. Federal Saf ety Requirements.
All tires are also graded f or
treadwear, traction, and temperature
perf ormance according to
Department of Transportation
(DOT) standards. The f ollowing
explains these gradings.
The treadwear grade is a compara-
tive rating based on the wear rate of
the tire when tested under controlled
conditions on a specif ied government
test course. For example, a tire
graded 150 would wear one and one-
half (1 1/2) times as well on the
government course as a tire graded
100. The relative perf ormance of
tires depends upon the actual condi-
tions of their use, however, and may
depart signif icantly f rom the norm
due to variations in driving habits,
service practices and dif f erences in
road characteristics and climate.
Unif orm T ire Quality Grading
T readwear 200
Traction AA
Temperature A T readwear
T raction
DOT Tire Quality Grading (U.S. Vehicles)
382
12/07/13 17:25:23 31TM8630_387
Technical Inf ormationTOC
2013 Insight