length HONDA INTEGRA 1994 4.G Owner's Manual

Regulator Valve Body
Disassembly/lnspection/Reassembly
NOTE:
a Clean all pans thoroughly in solvent or carburetor cleaner, and dry with compressed ait.a Blow out all passages.
a Replace valve body as an assembly it any parts are worn or damaged.a Check all valves for free movement. lf any fail to slide freely, see Valve Body Repair on page 14-117.
1. Hold the .egulator spring cap in place while removing the lock bolt. Once the bolt is removed. release the spring
cap slowlv.
CAUTION: The .egulator spring c8p can pop out whsn the lock bolt is removod.
2. Reassembly is in the reverse order of the disassembly procedute.
NOTE:
. Coat all pans with ATF.
a Align the hole in the regulator spring cap with the hole in the valve body, press the spring cap into the body andtighten the lock bolt.
LOCK.BOLT6 x 1.0 mm12 N.m (1.2 kgl.m, 8.7 lbf.ftl
REGULATOR SPRING CAP
COOLER CHECK
OOWEL PINS, 2
ROLLER
SPRING SPECIFICATIONS
Unit of length: mm (in)
../
I',.-2" ll"%=
VALVE SLEEVE
t,-V
,*6t'"
REGULATOR VALVE
REGULATOR VALVE BODY
No.Spring
Standard (New)
Wiro Dia.o.D.Free LonglhNo. of Coils
o/a
@
\9/
Regulator valve spring A
Regulator valve spring B
Stator reaction spring
Lock-up control valve spring
Cooler check valve spring
Torque converter check valve spring
1.80 (O.O71)
1.80 (0.071)
5.50 (O.2171
o.80 (o.o31)
1 .10 (0.043)
1 .10 (O.O43t
14.70 (O.5791
9.60 (0.378)'26.40 (1.O39)
6.60 (O.260)
8.40 (O.331)
8.40 (0.331)
88.60 (3.488t
44.OO t't.7321
30.30 (1 .1 93t
39.50 (1.555)
33.80 (1 .331 I
33.80 (1 .331 )
16.5
2.1
25.O'l2.5
12.5
14-122
lnside Diameter

NOTE:
a Clean all paris thoroughly in solvent or carburetor cleaner, and dry with compressed air.
a Blow out all passages.
a Replace valve body as an assembly it any parts are worn or damaged.
a Check all valves tor free movement. lf any fail to slide fre€ly, see Valve Body Repair on page 14-117.
a Coat all parts with ATF before reassembly.
LOCK-UP SHIFT VALVE
LOCK.UP TIMING 8 VALVE
,ar
\,/
SPRING SPECIFICATIONS
CAP
Unit ot length; mm (in)
No.Spring
Standard {Nsw}
Wile Di8.o.D.Flee LengthNo. of Coils
o
@
Lock-up shift valve spring
Lock-up timing B valve spring
o.90 (o.035)
o.80 (o.031)7.60 (0.299)
6.60 {O.260)
73.70 i.2.9021
60.80 (2.394)32.O
22.1
Disassembly/lnspection/Reassembly
14-123

CHECK BALL
CHECK BALLS
FILTER
SPRING SPECIFICATIONS
Unit ot length: mm (in)
No.Spring
Standard (N€wl
Wire Dia.o.D.Free LengthNo. of Coils
o
@
tcl
\9
@
3-2 kick-down valve spring
4-3 kick-down valve spring
Orifice control valve spring
2-3 orifjce control valve spring
3-4 shift valve spring
Servo control valve spring
Modulator valve spring
1 .3 {O.051)
1 .O (O.O39)
o.8 (o.031)
o.9 (o.03s)
0.9 {0.035)
o.9 (o.o35)
1.3 (O.O51)
8.6 tO.339)
6.6 (O.260)
6.6 (0.260)
6.6 (0.260)
7.6 (O.299)
6.4 lO.252l
9.4 (O.370)
45.6
28.5
48.2
33.O
52.O
34.1
37.3
1.795)
1 .1221
1.898)
1.299)
2.O47l
1.343)
1 .469)
17 .O
14.7
33.O
14.9
26.8
12.4
14-125

No.SpringSt8ndard {Newl
Wire Dia.o.D.Fre6 LongthNo. ot Coils
orar
6\
ra\
o
@(!,
@
Throttle valve B adiusting spring
Throttle valve B sp.ing
Throttle valve B spring
Throttle valve I spring
4th accumulator spring
1st accumulator spring
3rd accumulator sp.ing
2nd accumulator spring
0.7 (0.028)
1.4 (O.O55)
1.4 (O.O55)
1.4 (O.O55)
2.6 l0.102l
2.5 (O.O98)
2.8 (O.1 10)
3.6 (O.142)
6.2 t0.244l
8.5 (O.33s)
8.5 (O.3351
8.5 {0.33st
16.3 (O.642)
16.3 (O.642)
17.5 (O.689)
22.O (O.866)
34.O (1.339)
41.5 ( 1 .6341
41.5 ( 1 .634)
41.6 (1.638)
103.3 (4.067)'l 05.4 (4. 1 50)
105.2 14.142].
108.9 (4.287)
15.2
10.5
11.2
12.4
16 + 8.6
19.1
15.2
SPRING SPECIFICATIONS
Unit of length: mm (in)
14-127

1st-hold Accumulator/Right Side Cover
Disassembly/lnspection/Reassembly
NOTE:
a Clean all pans thoroughly in solvsnt o, carburetor cleaner, and dry with compressed 8ir.
a Blow out all passages.
a coat all parts with ATF betors raassembly.
SNAP RI]TG
l ST.HOLO ACCUMULATOR COVER
1ST-HOLD ACCUMULATOR SPRING
IST.HOLD ACCUMULATOR PISTON
RIGHT SIDE COVER
O.BINGR6place.
SPRING SPECIFICATIONSUnit of length: mm (in)
No.Spring
St8ndard lt{ew)
Wlro Dia.o.D.Froo LengthNo. of Coils
o1 st-hold accumulator spring4.00 (o.1 57)21.50 (0.846)71.70 l2.A23l8.3
14-128

8.Pack the inboard joint with the ioint grease included
in the new driveshaft set.
Grease quantity; 120 - 130 g 11.2 - 4.6 ozl
9. Fit the inboard joint onto the driveshaft.
NOTE;
. Reinstall the inboard joint onto the driveshaft by
aligning the marks on the inboard ioint and the
rollers.
. Hold the driveshaft so the inboard joint points up
to prevent it from falling off.
Left drivoshaft:Align the holder direction of the rollers
toward the slot ot inboard joint as
INBOARDJOINT
/,.-:--\ \
I sotine di,ection
A\
{(@}
HOLDER
10.Adjust the length of the driveshafts to the figure
below. then adjust the boots to halfway between
full compression and full extension.
NOTE: The ends of boots seat in the groove of the
driveshaft and joint.
Left: 475 - 480 mm {18.7 - 18.9 inl
Right: 475 - 480 mm (18.7 - 18.9 inl
lnstall new boot bands on the boots, and bend both
sets of locking tabs.
Lightly rap on the doubled-over portions to reduce
their height.
{cont'd)
11.
16-9

60.
Install the new lock washor in the groov€ in the
steering rack.
Hold the steering rack with I wrsnch and tighten
the rack end.
After tightening th€ rack end, stske the four sections
of lock washer with a commercially available roll
Din drift and a mallet.
ROLL PIN DRIFTComm.rcl.lly Av|il.bl.
lsnrp-On No. PPR8 or .rquiv.lenll
NOTE: This drift has a fl8t,
to prevent puncturing
of motal washer.
ol
62.Apply steering groass to the circumferenc6 of tho
rack end housing.
Coat the rack end groove and inside of the boot
with silicone greas€.
lnstsll the boots in ths rack end with the tube
clamos.
NOTE: Install the boots with the rack in the straight
ahsad position (i.6. right and l€ft tis-rods ar€ squal
in length).
(cont'dl
64.
NOTE: Wipe ths gro.se offthe thread s€ction.
TUEE CLAJTIP
17-61

Starter Brush Holder Test
1 . Check that there is no continuity between the O and
O brush holders. lf continuity exists. replace theb,ush holder assembly,
G) BRUSH HOLDER E BRUSH HOLOER
O BRUSH I{OLDERO BRUSH HOLDER
Insert the brush into the brush holder, and bring thebrush into contact with the commutator, then attacha spring scale to the spring, Measure the spring ten-sion at the moment the spring lifts off the brush.
Spring Tension: 17.7 -23.5 N {1.8-2.4 kgf,4.O_5.3 tbfl
SPRING SCLAE
Starter Brush Inspection
Measure the brush length. lf it is less than the servicelimit, replace the armature housing and brush holder as-sembly.
Brush L€ngth
Standard {Now): 15.O- 15.5 mm (0.59-0.61 inlSe.vice Limit: 10.0 mm (0.39 inl
NOTE: To seat new brushes after installing them in their
holders, slip a strip of # 5OO or # 600 sandpaper, with
the grit side up. over the commutator and smoothly ro-
tate the armature. The contact surface of the brushes
will be sanded to the same contour as the commutato..
23-81

RectifierTest
NOTE: The diodes are designed to allow current to pass
in one direction while blocking it in the opposite direc-
lion. Each diode must be tested for continuitv in both
directions with an ohmmeter that has diode checking
capability. Since the alternator rectifier is made up of
eight diodes (four pairs), there are a total of '16 checks,
1. Check for continuity in each ditection between the
B and P terminals, and between the E (ground) and
P terminals of each diode pair. All diodes should have
continuity in only one direction,
lf any of the eight diodes tails, replace the rectifier
assembly. (Diodes are not available separately.)
Gharging System
Alternator Brush Inspection
Remove the end cover, then lake oul the brush
holder by removing its two screws
Measure the length of the brushes with a vernier
calioer.
Aliornatol Brush Longlh:
Standard: 10.5 mm (O.41 in)
Servic. Limit: 1.5 mm (O.06 in)
lf the brushes are less than the service limit, replace
the b.ush holder assemblv.
VERI{IEB CALIPEB
23-106