11-52 HONDA INTEGRA 1994 4.G Workshop Manual

Troubleshooting
Self-diagnostic Procedures (cont'dl
':818C1 engine
a lf codes other than those listed above are indicated, verifv the code. lf the code indicated is not listed above, replace
rhe ECM.
a The MIL may come on, indicating a system problem when, in fact, there is a poor or intermittent electricalconnection.
First, check the electrical connections, clean or repair connections it necessary.
o The MIL and @ indicator light may light simultaneously when the Diagnostic Trouble Code (DTC) 6, 7 or 17. Check
the PGM-Fl system according to the PGM-Fl system troubleshooting, then recheck the l!! indicator light. ll it lights,
see page 14-5O, 51.
a The MIL does not come on when there is a malfunction in the A/T Fl signal or Electrical Load Detector (ELDI circuits.
However, it will indicate the codes when the Service Check Connector is shorted.
DIAGNOSTIC
TROUBLE
CODE (DTCISYSTEM INDICATEDPsge
oENGINE CONTROL MODULE IECM)11-42
,lHEATED OXYGEN SENSOR IHO25)1 1-46
aMANIFOLD ABSOLUTE PRESSURE {MAP SENSOR)11-52
4CRANKSHAFT POSITION (CKP SENSOR)1 1-56
oENGINE COOLANT TEMPERATURE (ECT SENSOR)11-58
THROTTLE POSITION (TP SENSOR}11-60
ITOP DEAD CENTER POSITION (TDC SENSORI1 1-56
9No. 1 CYLINDER POSITION (CYP SENSOR)1 1-56
10INTAKE AIR TEMPERATURE (IAT SENSOR)11-62
13BAROMETRIC PRESSURE (BARO SENSOR}1|-64
14IDLE AIR CONTROL (IAC VALVE}11-42
tcIGNITION OUTPUT SIGNAL11-66
toFUEL INJECTOR1't-102
17VEHICLE SPEED SENSOR {VSSI11-68
20ELECTRICAT LOAD DETECTOR (ELD)'t 1-70
21VARIABLE VALVE TIMING & VALVE LIFT ELECTRONIC CONTROL SOLENOID
VALVE {VTEC SOLENOID VALVE)'6-36
22VARIABLE VALVE TIMING & VALVE LIFT ELECTRONIC CONTROL PRESSURE
SWITCH (VTEC PRESSURE SWITCHI-6-38
23KNOCK SENSOR {KS}-11-7 4
30A/T FI SIGNAL A11-76
3'rA/T FI SIGNAL B1 1-76
4'lHEATED OXYGEN SENSOR (HO25} HEATER11-47
43FUEL SUPPLY SYSTEM1 1-50
11-36

PGM-FI System
Manifold Absolute Pressure (MAP) Sensor
fxai - lfil1 The Malfunction Indicator Lamp (MlL) indicates Diagnostic Trouble Code (DTC) 3: An electrical
-:- -?- problem in the Manifold Absolute Pressure (MAPI Sensor circuit.
The MAP sbnsor converts manitold absolute pressure into electrical signals and inputs the ECM.
OUTPUTVOLTAGE
600 700
(in. Hsl GAUGEREADIIIO{mft Hg)
YEL/RED lBlSBl onginc)YEL^YHT lBlaCl .ngin.l | + I
{+l
SENSOR
1.5
- Tho MIL has boon roportod on.- Wirh tho SCS rhort connoctorconnectod lsoo pags 11-34),codo 3 b indicatsd.
Do the ECM Reset Procedure {soepage 11-35).
Intormittont tailuro, lystom ir Ol(at thls timo {tort drivo may bsnocessary).Chack to? Door connocllon oiloosa wiroa 6t C223 {locltod atright shock tow6rl, C'l 14 (MAP
sonaorl and ECM.
ls the MIL on and does it indi-cate code 3?
Turn the ignition switch OFF.
Disconnect the 3P connector tromthe MAP sensor,
Turn the ignition switch ON.
{To page 11-53)
11-52

Intake Air System
Throttle Body (cont'dl
11-122
Dirarssmbly
GAUTION:
a Ths throttlo stop scrow is non-adrustablo.
a Aftar reassombly, adiust rhr throttlo Gablo (pago 11-118, 1 19). and A/T throttlo contlol cabl6 (section 14) for c!r8
rYith A/T.
a Tho TP sonaor ir not lomovablo
MAPSENSORTroubleshootingpage 11-52
TPSETSORTroubleshootingpoge 1l-60
O.BING
I
d^'%
IDLE ADJUSTINGSCREW
o-RtftGReplace.
FAST IDLETHERMOVALVEInspection, page 11-94
1O N.m11.O kgl.m.7 tbf.ftl