remove panel HONDA ODYSSEY 2011 RB3-RB4 / 4.G User Guide

Youshoulddothefollowingchecks
and adjustments bef ore you drive
your vehicle.Make sure all windows, mirrors,
and outside lights are clean and
unobstructed. Remove f rost, snow,
or ice.
Check that the hood is f ully closed.
Check that any items you may be
carrying are stored properly or
f astened down securely. Check the steering wheel
adjustment (see page ).
Make sure the doors and the
tailgate are securely closed and
locked.Fasten your seat belt. Check that
your passengers have f astened
their seat belts (see page ).
When you start the engine, check
the gauges and indicators in the
instrument panel, and the
messages on the inf ormation
display or multi-inf ormation
display (depending on models)
(seepages,,,and
).
Visually check the tires. If a tire
looks low, use a gauge to check its
pressure. Check the seat adjustment (see
pages and ).
Check the adjustment of the
inside and outside mirrors (see
pages and ).
3. 2.
1.
4. 5.
6.
7.
8. 9.
10. 15
176
175
198
197
63 64 77
90
143Preparing to Drive558
10/07/17 10:49:39 31TK8600_563
2011 Odyssey

CONT INUED
Remove the socket f or that bulb
by turning it one-quarter turn
counterclockwise. Determine which of the two bulbs
is burned out: stop/taillight or turn
signal light.
Rotate the assembly toward the
side panel until it slightly overlaps
the bumper and the bottom of the
taillight housing is exposed.
With the hand closest to the cargo
area, use your f ingers to grip the
bottom edge of the assembly.
Apply a rearward and upward
pulling motion to release the lower
f astener f rom the grommet.
Continue to support the assembly
while placing the f ingers of the
outer hand on the top of the outer
corner of the assembly.
Pull with the upper f inger and
hand to release the upper f astener
f rom the top grommet.
2.
3.
4.
5.
6.7.
8.
Lights
Maint enance
631
BULB
SNAP FASTENERS
SOCKET
10/07/17 10:58:44 31TK8600_636
2011 Odyssey

Pull the bulb straight out of its
socket. Push the new bulb straight
into the socket until it bottoms.
Reinstall the socket into the light
assembly by turning it one-quarter
clockwise until it locks.
Turn on the lights to make sure
the new bulb is working.
Ensure that the grommets are still
in place on the body panel.Open the tailgate. Place a cloth on
the edge of the cover to prevent
scratches. Remove it by caref ully
prying in the notch on its edge
with a small f lat-tip screwdriver.
Determine which of the two bulbs
is burned out: taillight or back-up
light.
Insert the fasteners into the
grommets and push the assembly
back into place. You will hear the
f asteners engage.
Install the mounting bolts and
tighten securely.
1.
2.
9.
11. 10.
12. 14. 13.
Lights
Replacing Rear Bulbs
(in Tailgate)
632
COVER
GROMMET
FASTENER
If the grommets are loose or completely
out of the holes af ter the taillight
assembly is removed, they must be
replaced. Ask your dealer f or more
inf ormation.
10/07/17 10:58:53 31TK8600_637
2011 Odyssey

The vehicle’s f uses are located in
five fuse boxes.
Thedriver’ssideinteriorfuseboxis
under the dashboard on the driver’s
side. The fuse label is attached to the
side panel.Therearfuseboxislocatedatthe
lef t side of cargo area.
Place a cloth on the edge of the
cover to prevent scratches, then
remove it by caref ully prying in the
notch on its middle edge with a small
f lat-tip screwdriver.
The passenger’s side interior f use
box is under the dashboard. Push
down the tab and slide the cover
upward to remove it.
CONT INUED
Fuses
Taking Care of the Unexpected
673
INTERIOR (Driver’s side)
INTERIOR (Passenger’s side)INTERIOR (Rear)
FUSE LABEL NOTCH
COVER
COVER
NOTCH
10/07/17 11:04:14 31TK8600_678
2011 Odyssey