bulb HONDA ODYSSEY 2011 RB3-RB4 / 4.G Owners Manual

If this indicator begins to f lash,
there is a problem with the tire
pressure monitoring system
(TPMS). You will also see a
‘‘CHECK TPMS SYSTEM’’
message on the multi-inf ormation
display. The indicator continues to
f lash f or a while (approximately 1
minute), then stays on. If this
happens, have your dealer check
the system as soon as possible.
For more inf ormation, see page.This indicator normally comes on f or
a f ew seconds when you turn the
ignition switch to the ON (II)
position.
If this indicator comes on and stays
on at any other time, or if it does not
come on when you turn the ignition
switch to the ON (II) position, there
is a problem with the TPMS. With
this indicator on, the low tire
pressure indicator will not come on
when a tire loses pressure. Take the
vehicle to your dealer to have the
system checked. For more
inf ormation, see page . The lef t or right turn signal indicator
blinks when you signal a lane change
or turn. If an indicator does not blink
or blinks rapidly, it usually means
one of the turn signal bulbs is
burned out (see pages and ).
Replace the bulb as soon as possible,
since other drivers cannot see that
you are signaling.
When you press the hazard warning
button, both turn signal indicators
and all turn signals on the outside of
the vehicle f lash.
2.
577 628 631
573
On LX, EX, EX-L models
Instrument Panel Indicators
Tire Pressure Monitoring
System (T PMS) Indicator Turn Signal and
Hazard Warning
Indicators
72
10/07/17 09:44:02 31TK8600_077
2011 Odyssey

CONT INUED
Theheadlightswereproperlyaimed
when your vehicle was new. If you
regularly carry heavy items in the
cargo area or pull a trailer,
readjustment may be required.
Adjustmentsshouldbedonebyyour
dealer or other qualif ied technician.Your vehicle has halogen headlight
bulbs. When replacing a bulb, handle
it by its base, and protect the glass
f rom contact with your skin or hard
objects. If you touch the glass, clean
it with denatured alcohol and a clean
cloth.
The low beam headlight bulbs are a
type of high voltage discharge tube.
High voltage can remain in the
circuit even with the light switch of f
and the key removed. Because of
this, you should not attempt to
examine or change a low beam
headlight bulb yourself . If a low
beam headlight bulb fails, take your
vehicle to a dealer to have it replaced.
On Touring Elite and Canadian Touring
models
Lights
Headlight A iming Replacing a Headlight Bulb
High Voltage Discharge Tube
Headlights
Maint enance
625
Halogen headlight bulbs get very hot
when lit. Oil, perspiration, or a scratch
on the glass can cause the bulb to
overheat and shatter.
10/07/17 10:57:48 31TK8600_630
2011 Odyssey

Open the hood.
To change a bulb on the driver’s
side, remove the upper part of the
air intake duct.
Use a f lat-tip screwdriver to
remove the holding clip, then
remove the upper part.To change a bulb on the
passenger’s side, use a f lat-tip
screwdriver to remove the holding
clip f rom the engine coolant
reserve tank, and then remove the
engine coolant reserve tank out of
its stay.
Remove the power steering
reservoir f rom the stay bracket to
get enough working space.
1.
2.
LightsHigh Beam Headlights626
HOLDING CLIPS
STAY
COOLANT RESERVE TANK
HOLDING CLIP POWER STEERING RESERVOIR
STAY BRACKET
10/07/17 10:57:56 31TK8600_631
2011 Odyssey

Insert the new bulb into the hole,
and turn it one-quarter turn
clockwise to lock it in place.
Push the electrical connector onto
the new bulb.
Turn on the headlights to test the
new bulb.
Remove the electrical connector
f rom the bulb by pushing on the
tab and pulling the connector
down.
Remove the bulb by turning it
about one-quarter turn
counterclockwise. Reinstall the air intake duct
securely.
Reinstall the engine coolant
reserve tank and power steering
reservoir. Open the hood.
Remove the electrical connector
f rom the bulb by pushing on the
tab and pulling the connector
down.
Remove the bulb by turning it
about one-quarter turn
counterclockwise.
4. 5.
6.
3. 7.
8.
2.
3. 1.
CONT INUED
Driver’s sidePassenger’s side
Lights
L ow Beam Headlight s
Maint enance
627
TAB
CONNECTOR BULB
BULBTAB
CONNECTOR
10/07/17 10:58:08 31TK8600_632
2011 Odyssey

Insert the new bulb into the hole,
and turn it one-quarter turn
clockwise to lock it in place.
Push the electrical connector onto
the new bulb.
Turn on the headlights to test the
new bulb.Open the hood.
Remove the socket from the
headlight assembly by turning it
one-quarter turn counterclockwise.
Pull the bulb straight out of its
socket.Turn on the lights to make sure
the new bulb is working. Insert the socket back into the
headlight assembly. Turn it
clockwise to lock it in place. Push the new bulb straight into
the socket until it bottoms.
1.
4.
5.
6.
2.
3. 4.
5.
6.
Lights
Replacing the Front Side Marker/
Parking/Turn Signal Light Bulb
628
BULB
SOCKET
10/07/17 10:58:18 31TK8600_633
2011 Odyssey

CONT INUED
Your vehicle uses halogen light
bulbs. When replacing a bulb,
handle it by its plastic case, and
protect the glass f rom contact with
your skin or hard objects. If you
touch the glass, clean it with
denatured alcohol and a clean
cloth.Thefoglightswereproperlyaimed
when your vehicle was new. If you
regularly carry heavy items in the
cargo area or pull a trailer,
readjustment may be required.
Adjustment should be done by your
dealer or another qualif ied
technician.
Start the engine. If you are
replacing a driver’s side bulb, turn
the steering wheel all the way to
theright.If youarereplacinga
passenger’s side bulb, turn the
steering wheel to the lef t. Turn of f
the engine. Use a 10 mm wrench to remove
the mounting bolt, and remove the
screws with a Phillips-head
screwdriver. Pull the inner f ender
cover back.
1.
2.On Touring models
Lights
ReplacingaFogLightBulb
Maint enance
629
SCREWS
MOUNTING BOLT
Halogen light bulbs get very hot when
lit. Oil, perspiration, or a scratch on
the glass can cause the bulb to overheat
and shatter.
10/07/17 10:58:25 31TK8600_634
2011 Odyssey

Remove the electrical connector
f rom the bulb by pushing on the
tab to unlock it, then slide the
connector of f the bulb.
Remove the bulb by turning it
approximately one-quarter turn
counterclockwise.Insert the new bulb into the hole,
and turn it one-quarter turn
clockwise to lock it in place.
Push the electrical connector back
onto the bulb. Make sure it is on
all the way.
Reinstall the inner f ender. Make
sure it is installed under the edge
of the f ront bumper.
Reinstall the screws and mounting
bolt on the inner f ender cover, and
tighten them securely. Turn on the f og lights to test the
new bulb.
Open the tailgate.
Use a Phillips-head screwdriver to
remove the two mounting bolts.
3.
4. 5.
7. 6.
8.
9.
1.
Lights
Replacing Rear Bulbs
(in Rear Pillar)
630
BULB
TAB CONNECTOR Pull up
Slide
MOUNTING BOLTS
10/07/17 10:58:35 31TK8600_635
2011 Odyssey

CONT INUED
Remove the socket f or that bulb
by turning it one-quarter turn
counterclockwise. Determine which of the two bulbs
is burned out: stop/taillight or turn
signal light.
Rotate the assembly toward the
side panel until it slightly overlaps
the bumper and the bottom of the
taillight housing is exposed.
With the hand closest to the cargo
area, use your f ingers to grip the
bottom edge of the assembly.
Apply a rearward and upward
pulling motion to release the lower
f astener f rom the grommet.
Continue to support the assembly
while placing the f ingers of the
outer hand on the top of the outer
corner of the assembly.
Pull with the upper f inger and
hand to release the upper f astener
f rom the top grommet.
2.
3.
4.
5.
6.7.
8.
Lights
Maint enance
631
BULB
SNAP FASTENERS
SOCKET
10/07/17 10:58:44 31TK8600_636
2011 Odyssey

Pull the bulb straight out of its
socket. Push the new bulb straight
into the socket until it bottoms.
Reinstall the socket into the light
assembly by turning it one-quarter
clockwise until it locks.
Turn on the lights to make sure
the new bulb is working.
Ensure that the grommets are still
in place on the body panel.Open the tailgate. Place a cloth on
the edge of the cover to prevent
scratches. Remove it by caref ully
prying in the notch on its edge
with a small f lat-tip screwdriver.
Determine which of the two bulbs
is burned out: taillight or back-up
light.
Insert the fasteners into the
grommets and push the assembly
back into place. You will hear the
f asteners engage.
Install the mounting bolts and
tighten securely.
1.
2.
9.
11. 10.
12. 14. 13.
Lights
Replacing Rear Bulbs
(in Tailgate)
632
COVER
GROMMET
FASTENER
If the grommets are loose or completely
out of the holes af ter the taillight
assembly is removed, they must be
replaced. Ask your dealer f or more
inf ormation.
10/07/17 10:58:53 31TK8600_637
2011 Odyssey

Remove the socket by turning it
one-quarter turn counterclockwise.
Pull the bulb straight out of its
socket. Push the new bulb straight
into the socket until it bottoms.
Pull the bulb straight out of its
socket. Push the new bulb straight
into the socket until it bottoms.
Insert the socket back into the
light assembly. Turn it clockwise
to lock it in place.
Reinstall the base gasket.
Push the electrical connector back
onto the socket. Make sure it is on
all the way.
Turn on the lights to make sure
the new bulb is working.
Reinstall the cover.
Remove the electrical connector
f rom the bulb by pushing on the
tab to unlock it, then slide the
connector of f the bulb.
Remove the base gasket as shown,
then remove the socket by turning
it one-quarter turn
counterclockwise. 4.
5.
6.
9.
3.
8. 7. (Taillight)
10.
(Back-up light)
3.
4.
Lights
Maint enance
633
BULB
SOCKET
CONNECTOR
BULB TAB
SOCKET
BASE GASKET
10/07/17 10:59:04 31TK8600_638
2011 Odyssey