mileage HONDA PASSPORT 2002 2.G Owners Manual

162Driving Tips
Self-Adjusting Brakes
The brakes on this vehicle are
self-adjusting. They have been
designed so that periodic brake
adjustment is not needed.
The brakes adjust themselves each
time you firmly apply them.
Thus, if the brake pedal goes down
farther than normal due to a lack of
adjustment, drive backward and
forward a few times. Apply the
brakes intermittently.
See your Honda dealer if the
brake pedal height does not return
to normal or if there is a rapid
increase in pedal travel. Either is a
sign of other brake trouble. Also,
see your Honda dealer if the
parking brake needs adjustment.
Braking Tips
Control your vehicle’s speed on a
steep or long downhill grade by
shifting the transmission to a
lower gear. Constantly using the
brakes can cause them to overheat
and lose effectiveness.
Resting your foot on the brake
pedal when you are not intending
to brake (“riding the brakes”) can cause them to overheat. This
reduces their effectiveness, wears
them out faster, and can reduce
fuel mileage. It also causes your
brake lights to stay on all the time,
confusing drivers behind you.
Brake Wear Indicators
The front and rear brakes have
built-in wear indicators. These make a high-pitched squealing or
cricket-like warning sound when
the brake pads or linings are worn
to the point of replacement. The
sound may come and go or be
heard all the time when the vehicle
is moving, but may stop when the
brake pedal is pushed down firmly.
Expensive damage can result if
pads or linings are not replaced
immediately when needed.
Driving on Slippery Surfaces
Driving, steering, and braking
traction are reduced when the
road is coated with water, snow,
ice, gravel, or other materials.
Slow down and adjust your
driving to such conditions. It is
important to slow down when it is
slippery because stopping

169Driving Tips
Wheel Replacement
Considerations
Damaged wheels must be
replaced. For example, replace
wheels if they are bent, cracked or
heavily rusted, or if wheel nuts
often become loose. Also replace
wheels that leak air (except some
aluminum wheels that can be
repaired). See your Honda dealer.
Do not use bent wheels that have
been straightened, and do not use
tubes in leaking wheels designed
for tubeless tires. Such wheels
may have structural damage and
could fail without warning.
Maximum loads, maximum
inflation pressures, wheel
identification codes, and wheel
sizes are stamped on each wheel.
Service-tested and approvedwheels are available from your
Honda dealer.
When obtaining wheels for any
reason from any other source, the
replacement wheels should be
equal in load capacity, inflation
pressure capacity, diameter, width,
offset and mounting configuration
to those originally installed on
your vehicle. A wheel of the
wrong size or type may adversely
affect load carrying capacity,
wheel and bearing life, brake
cooling, speedometer/odometer
calibration, stopping ability,
headlight aim, bumper height,
vehicle ground clearance, and tire
or tire chain clearance to the body
and chassis. Replacement with
used wheels is not advised: They
may have been subjected to harsh
treatment or very high mileage and
could fail without warning.
Installing wheels and/or tires that
have a higher load carrying limit
than those that originally came on
your vehicle does not increase the
GAWR or GVWR of the vehicle.

converter. These replacements
are not covered under warranty.
173Driving Tips
If you are planning to take your
Honda outside the U.S. or
Canada, contact the tourist
bureaus in the areas you will be
traveling in to find out about the
availability of unleaded gasoline
with the proper octane rating.
If unleaded gasoline is not
available, be aware that using
leaded gasoline in your Honda
will affect performance and fuel
mileage, and damage its
emissions controls. It will no
longer comply with U.S. and
Canadian emissions regulations,
and will be illegal to operate in
North America. To bring your
vehicle back into compliance will
require the replacement of several
components, such as the oxygen
sensor and the three-way catalytic
Modifying your vehicle, or
installing some non-Honda
accessories, can make your vehicle
unsafe. Before you make any
modifications or add any
accessories, be sure to read the
following information.
Accessories
Your dealer has Genuine Honda
accessories that allow you to
personalize your vehicle. These
accessories have been designed and
approved for your vehicle, and are
covered by warranty.
Non-Honda accessories are
usually designed for universal
applications. Although
aftermarket accessories may fit on
your vehicle, they may not meet
factory specifications, and could
adversely affect your vehicle
’s
handling and stability. (See “Modifications” on the next page
for additional information.)
Improper accessories or
modifications can affect
your vehicle’
s handling,
stability and performance,
and cause a crash in
which you can be hurt or
killed.
Follow all instructions in
this owner ’s manual
regarding accessories and
modifications.
When properly installed, car
phones, alarms, two-way radios,
and low-powered audio systems
should not interfere with your
vehicle’ s computer-controlled
Operation in
Foreign CountriesAccessories & Modifications

213Care and Maintenance
Oil Viscosity
Engine oil viscosity (thickness) has
an effect on fuel economy. Lower
viscosity engine oils can provide
increased fuel economy; however,
higher temperature weather
conditions require higher viscosity
engine oils for satisfactory
lubrication. To get the best fuel
economy with your vehicle, you
should use a fuel-saving engine oil
of the proper viscosity. These oils
can be found in service stations andother retail stores. They are
identified by words such as
“Energy Saving,” “Conserves
Gasoline,” “Gas Saving,”
“Gasoline Saving,” “Friction
Reducing,” “Improved Gasoline
Mileage” or “Fuel Saving.”
The chart lists the recommended
engine oil viscosities for the
temperature range you expect
before the next oil change. For
temperatures above 0

F (–18
C),
SAE 10W–30 is the preferred viscosity grade. If cold-weather
starting problems are encountered
at temperatures below 0

F
(–18
C), SAE 5W–30 viscosity
oils may be required.
Oil Level Check
It is the owner ’s responsibility to
keep the engine oil at the proper
level. Check the oil level at regular
intervals (such as every other fuel
stop) and keep it above the
“minimum” level mark.
Remember, your engine may use
more oil when it is new.
The best time to check the engine
oil level is when the oil is warm,
such as during a fuel stop. Shut off
the engine and wait about 5 minutes
for the oil to drain back to the oil
pan. Pull out the dipstick, wipe it
clean, and push it back down all the
way. Now pull out the dipstick and
–20 F 0 F
– 30 C –20 C –10 C 20 F
40 F
0 C 10 C 20 C
60 F
80 F
30 C 40 C
100 F
TEMPERATURE RANGE YOU EXPECT BEFORE NEXT OIL CHANGE
VISCOSITY GRADE – AMBIENT TEMPERATURE
SAE 5W–30
SAE 10W–30, PREFERRED
SAE 15W–40, 20W–40, 20W–50

216Care and Maintenance
Proper Fluid
Kind of Fluid
TransmissionDEXRON III
Transfer
(4WD)SAE 5W-30
(Engine oil)
Have the fluid level in the
automatic transmission checked
during the regularly scheduled
maintenance at your Honda
dealer.
If you suspect an automatic
transmission fluid leak, take the
vehicle to your Honda dealer for
inspection and repair.
Transmission damage could result
if you let the fluid level get too
low.
Drain Intervals
The automatic transmission drain
interval is not time or mileage
dependent. It will vary according
to your driving habits and vehicle
usage.
Your dealer will check the
transmission fluid’s condition and
life expectancy during regularly
scheduled maintenance, and
inform you at what mileage it
should be changed. See the Maintenance Schedule
List to determine how often the
lubricant should be changed. Add
lubricant, if needed, by filling to
the level of the filler plug hole.
Use
GL-5 gear lubricant of the
proper viscosity as shown in the
chart.
If your vehicle is equipped with
the optional limited slip
differential (on the rear axle), use
GL-5 Limited Slip Differential
Gear Lubricant together with
Limited Slip Differential Gear
Lubricant Additive (Part No.
8-01052-358-0) or equivalent.
Use the correct viscosity for the
existing ambient temperatures.
Automatic Transmission FluidFront (4WD)
and Rear Axles

224Care and Maintenance
Wheel Alignment
Proper wheel alignment improves
tire mileage. Your vehicle’s
suspension parts should be
inspected often and aligned when
needed (see the “Technical Data”
section). Improper alignment will
cause the front tires to roll at an
angle that will result in faster tire
wear.
Proper tire balancing provides the
best riding comfort and helps
reduce tire tread wear.
Out-of-balance tires can cause
annoying vibration and uneven
tire wear such as cupping and flat
spots.
Washing Your Vehicle
The best way to preserve your
vehicle ’s finish is to keep it clean by
frequent washings. Wash the vehicle
with lukewarm or cold water.
Do not use hot water or wash in
direct sunlight. Do not use strong
soap or chemical detergents. All
cleaning agents should be promptly
flushed from the surface and not
allowed to dry on the finish.
Polishing and Waxing
Your Vehicle
Polishing is recommended to
remove accumulated residue and
eliminate any “weathered”
appearance.
Your Honda dealer offers several
polishes and cleaners that have
proven to maintain the original
finish appearance and durability.
Protection of Exterior
Bright Metal Parts
Bright metal parts should be cleaned
regularly to keep their luster.
Washing with water is all that is
usually needed. However, chrome
polish may be used on chrome or
stainless steel trim, if necessary. A
coating of wax, rubbed to a high
polish, is recommended for all bright
metal parts.
Care of Aluminum Wheels
Aluminum wheels have a
clear-coat finish similar to paint.
Use a chamois skin, sponge or
other soft material when washing
the wheels.
Foreign Material Deposits
Calcium chloride and other salts,
ice melting agents, road oil and
tar, tree sap, bird droppings,
Exterior

246 Owner Assistance
Your satisfaction and goodwill are
important to your Honda dealer
and to us, American Honda Motor
Co., Inc. Honda dealership
personnel are trained
professionals. They should be
able to answer all your questions.
If you encounter a problem that
your dealership does not solve to
your satisfaction, please discuss it
with the dealership’s
management. The Service
Manager or General Manager can
help. Almost all problems are
solved in this way.
If you are dissatisfied with the
decision made by the dealership’s
management, contact your Honda
Consumer Affairs Department.
American Honda Motor Co., Inc.
Honda Consumer Affairs Dept.
1919 Torrance Boulevard
Mail Stop 500-2C-7D
Torrance, California 90501-2746
(800) 999-1009 When you call or write, please
give us this information:
1.
Your name, address and
telephone number
2. Vehicle Identification Number
(see page 232)
3. The name and address of the dealer who services your
vehicle
4. Date of purchase
5. Mileage on your vehicle
6. Name and address of the dealer who sold you the
vehicle
7. A detailed description of the problem
Customer Relations Information

247Owner Assistance
Your new Honda is covered by
these warranties:
New Vehicle Limited Warranty
–
Covers your new vehicle, except
for the battery, emissions control
systems and accessories, against
defects in materials and
workmanship.
Emission Control Systems
Defects Warranty and Emissions
Performance Warranty


These
two warranties cover your
vehicle’ s emission control
systems. Time, mileage, and
coverage are conditional. Please
read the warranty manual for
exact information.
Original Equipment Battery
Limited Warranty


This
warranty gives up to 100% credit
toward a replacement battery. Seat Belt Limited Warranty


A seat belt that fails to function
properly is covered for the useful
life of the vehicle.
Rust Perforation Limited
Warranty
 All exterior body
panels are covered for rust-through
from the inside for the specified
time period with no mileage limit.
Accessory Limited Warranty

Genuine Honda Accessories are
covered under this warranty. Time
and mileage limits depend on the
type of accessory and other
factors. Please read your warranty
manual for details.
Replacement Parts Limited
Warranty

– Covers all Genuine
Honda replacement parts against
defects in materials and
workmanship. Replacement Battery Limited
Warranty

 Provides prorated
coverage for a replacement
battery purchased from a Honda
dealer.
Replacement Muffler Lifetime
Limited Warranty

– Provides
coverage for as long as the
purchaser of the muffler owns
the vehicle.
Restrictions and exclusions apply
to all these warranties. Please read
the 2002 Honda Warranty booklet
that came with your vehicle for
precise information on warranty
coverages. Your Honda ’s original
tires are covered by their
manufacturer. Tire warranty
information is in a separate
booklet.
Warranty Coverages

259
Foreign Countries, Operation in
173. . . . . . . . . . . . .
Fuel Filling the Fuel Tank
197. . . . .
Fuel Fill Cap
197. . . . . . . . . . .
Fuel Gauge
59. . . . . . . . . . . . .
Low Fuel Indicator
64. . . . . .
Octane Requirement
200. . . . .
Oxygenated
200. . . . . . . . . . . .
Recommendation
198. . . . . . . .
Tank Capacity
198, 237. . . . . .
Fuel Injection System
249. . . . . .
Fuses Checking the
193, 240. . . . . . .
Locations
240. . . . . . . . . . . . . .
G
Gas Mileage, Improving170. . . . Gasohol
200. . . . . . . . . . . . . . . . .
Gasoline
200. . . . . . . . . . . . . . . . .
See also Fuel
Octane Requirement
200. . . . .
Tank, Filling the
197. . . . . . . . . . . .
Gas Station Procedures
197. . . . .
Gauges Engine Coolant Temperature
60. . . . . . . . . . .
Fuel
59. . . . . . . . . . . . . . . . . .
Speedometer
58. . . . . . . . . . .
Tachometer
58. . . . . . . . . . . .
GAWR (Gross Axle
Weight Rating)
233. . . . . . . . . . .
Gearshift Lever Positions Automatic Transmission
76. .
5-Speed Transmission
83. . . .
Glass Cleaning
230. . . . . . . . . . . . Glove Box
114. . . . . . . . . . . . . . .
GVWR (Gross Vehicle
Weight Rating)
233. . . . . . . . . .
H
Halogen Headlight Bulbs243. . . .
Hazard Warning Flasher
76. . . .
Head Restraints
8, 12, 93. . . . . . .
Headlights
72. . . . . . . . . . . . . . .
High Beam Indicator
62. . . . .
High Beams
72. . . . . . . . . . . .
On, Reminder
73. . . . . . . . . .
Replacing Halogen Bulbs
243.
Turning on
72. . . . . . . . . . . . .
Heating and Cooling
120. . . . . . .
High-Low Beam Switch
72. . . .
Hood Release
109, 199. . . . . . . . .
Horn
115. . . . . . . . . . . . . . . . . . . .
Hydroplaning
168. . . . . . . . . . . . .