lock HONDA S2000 2002 1.G Workshop Manual

Draining the coolant requires access
to the underside of the vehicle.
Unless you have the tools and
knowledge, you should have this
maintenance done by a skilled
mechanic. Turn the ignition ON (II). Turnthe heater temperature control
dial f ully clockwise. Turn the
ignition of f .
Openthehood.Makesurethe
engine and radiator are cool to the
touch.
Remove the radiator cap.Loosen the drain plug on the
bottom of the radiator. The
coolant will drain through the
splash guard. Remove the drain
bolt and washer f rom the engine
block.
Thecoolingsystemshouldbe
completely drained and ref illed with
new coolant according to the time
and distance recommendations in
the maintenance schedule. Only use
Honda All season Antif reeze/
Coolant Type 2.
1. 2. 3.4.
CONT INUED
Replacing Engine Coolant
Cooling Syst em
Maint enance
169
DDRRAAIINNBBOOLLTT
DDRRAAIINNPPLLUUGG

Remove the reserve tank f rom its
holder by pulling it straight up.
Drain the coolant, then put the
tank back in its holder.When the coolant stops draining,
tightenthedrainplugatthe
bottom of the radiator.
Apply non-hardening sealant to the
drain bolt threads, put a new
washer on the drain bolt, and
reinstall the bolt in the engine
block. Tighten it securely.
Tightening torque:
Loosen the bleeder bolt on top of
the engine, and remove the
bleeder cap near the engine oil f ill
cap.
5. 6.
7.
Cooling Syst em
Maint enance
170
RREESSEERRVVEETTAANNKKCCAAPP
HHOOLLDDEERRRREESSEERRVVEETTAANNKK
BBLLEEEEDDEERRBBOOLLTT
61 lbf·ft (83 N·m , 8.5 kgf·m)

To replace the blade: Disconnect the blade assemblyfromthewiperarmbypushingin
the lock tab. Hold it in while you
push the blade assembly toward
thebaseof thearm.
Raise the wiper arm of f the
windshield.
Check the condition of the wiper
blades at least every six months.
Look f or signs of cracking in the
rubber, or areas that are getting
hard. Replace the blades if you f ind
these signs, or if they leave streaks
and unwiped areas when used.
1.2.
Wiper Blades
Maint enance
186
LLOOCCKKTTAABB

Remove the blade f rom its holder
by grasping the tabbed end of the
blade. Pull f irmly until the tabs
come out of the holder.Examine the new wiper blades. If
they have no plastic or metal rein-
f orcement along the back edge,
remove the metal reinf orcement
strips f rom the old wiper blade and
install them in the slots along the
edge of the new blade.Slide the new wiper blade into the
holder until the tabs lock.
Slide the wiper blade assembly
onto the wiper arm. Make sure it
locks in place.
Lower the wiper arm down against
the windshield.
3. 4. 5. 6. 7.
Wiper Blades
Maint enance
187
RREEIINNFFOORRCCEEMMEENNTT
BBLLAADDEE

Run the air conditioning at least once
a week during the cold weather
months. Run it f or at least ten
minutes while you are driving at a
steady speed with the engine at
normal operating temperature. This
circulates the lubricating oil con-
tained in the ref rigerant.If the air conditioning does not get as
cold as before, have your dealer
check the system. Recharge the
system with Ref rigerant HFC-134a
(R-134a). (See Specif ications on page
.)
Your car’s air conditioning is a sealed
system. Any major maintenance,
such as recharging, should be done
by a qualif ied mechanic. You can do
a couple of things to make sure the
air conditioning works ef f iciently.
Periodically check the engine’s
radiator and air conditioning
condenser f or leaves, insects, and
dirt stuck to the f ront surf ace. These
block the air f low and reduce cooling
ef f iciency. Use a light spray f rom a
hose or a sof t brush to remove them. 253
A ir Condit ioning Syst em
Maint enance
188
AAIIRRCCOONNDDIITTIIOONNIINNGGCCOONNDDEENNSSEERR Whenever you have the air conditioning
system serviced, make sure the service
f acility uses a ref rigerant recycling
system. This system captures the
ref rigerant f or reuse. Releasing
ref rigerant into the atmosphere can
damage the environment.
The condenser and radiator f ins bend
easily. Only use a low-pressure spray
or sof t-bristle brush to clean them.

Open the hood. Unclip the
windshield base by pulling it up.Put the pins on the windshield
base into their mating holes on the
support, and push the base down
until the pins snap in.
Remove the old f ilter. Put a new
f ilter in the holder and push it in
until it locks.
The dust and pollen f ilter is located
in the engine compartment on the
passenger’s side near the base of the
windshield.
Push the tab on the dust and
pollen f ilter to unlock it f rom the
holder.
This f ilter should be replaced every
30,000 miles (48,000 km) under
normal conditions. It should be
replaced every 15,000 miles (24,000
km) if you drive primarily in urban
areas that have high concentrations
of soot in the air f rom industry and
diesel-powered vehicles. Replace it
more of ten if air f low f rom the
climate control system becomes less
than usual. Have the dust and pollen
f ilter replaced by your Honda dealer.
The dust and pollen f ilter removes
pollen and dust f rom the outside air,
The heating and cooling system
brings air into the interior. It should
be replaced according to the time
and distance recommendations in
the maintenance schedule.
1.2. 3.4.
Maint enance
Replacement
Dust and Pollen Filt er
189

Open the hood.
Remove the electrical connector
f rom the bulb by squeezing the
connector to unlock the tab, then
slide the connector of f the bulb.Remove the rubber weather seal
by pulling on the tab.
Pull the bulb straight out of its
socket.
If you need to change the high
beam headlight bulb on the lef t
side, remove the coolant reserve
tank f rom its holder by pulling it
straight up.
Unclip the end of the hold-down
wire f rom its slot. Pivot it out of
the way and remove the bulb
socket.Install the rubber seal over the
back of the headlight assembly.
Make sure it is right side up; it is
marked ‘‘TOP.’’
Push the electrical connector onto
the new bulb.
Push the new bulb straight into
the socket until it bottoms. Turn on the headlights to test the
new bulb.
Insert the socket back into the
headlight assembly. Make sure
the bulb is installed correctly by
looking through the headlight lens.
The pins on the base of the bulb
should f it in the holes in the
headlight assembly. Pivot the hold-
down wire back in place and clip
the end into the slot.
1. 2. 3. 4. 5.6. 7. 8.
Lights
Maint enance
201

If you are changing the bulb on
the driver’s side, start the engine,
turn the steering wheel all the way
to the right, and turn off the
engine. If you are changing the
bulb on the passenger’s side, turn
the steering wheel to the left.Pull the inner f ender cover back.
Remove the socket from the
headlight assembly by turning it
one-quarter turn counterclockwise.
Pull the bulb straight out of its
socket.Install the new bulb in the socket.
Insert the socket back into the
headlight assembly. Turn it
clockwise to lock it in place.
Testthelightstomakesurethe
new bulb is working.
Put the inner f ender in place.
Install the two holding clips. Lock
each clip in place by pushing on
the center.
Use a f lat-tipped screwdriver to
remove the three holding clips
f rom the inner f ender.
1.
2. 3. 4. 5.6. 7. 8. 9.
Lights
Maint enance
Replacing Front Turn Signal and
Side Marker L ight Bulbs 202

Pull the bulb straight out of its
socket.
Push the new bulb straight into
the socket until it bottoms.
Put the bulb holder back into its
hole in the lens, and turn it
clockwise until it locks.
Testthelightstomakesurethe
new bulb is working.
Use a small f lat blade screwdriver
to pry caref ully on the back edge
of the side turn signal assembly
until it pops out of the body.
Turn the bulb holder one-quarter
turn counterclockwise to remove it
from the lens. Put the side turn signal assembly
back into the body, front first.
Push on the back edge until it
snaps into place.
1. 2. 3. 4. 5. 6.
Lights
Maint enance
Replacing a Side T urn Signal Bulb
203

Open the trunk. Determine which of the f our bulbsis burned out: stop/taillight, back-
up light, turn signal, or side
marker.Remove the socket by turning it
one-quarter turn counterclockwise.
Remove the fasteners from the
trunk lining. To remove a f astener,
push on the center of the head
until it pops in. Then pull it out.
Pull the lining back. Remove the burned out bulb. To
remove the stop/taillight, back-up
or side marker light bulb, pull the
bulb straight out of its socket. To
remove the turn signal light bulb,
push it in and turn it
counterclockwise until it unlocks.
1. 2. 3.
4.
5. 6.
Lights
Maint enance
Replacing Rear Bulbs 204