instrument panel HONDA S2000 2003 1.G User Guide

Î
Î
Thetwoleversonthesteering
column contain controls f or driving
f eatures you use most of ten. The lef t
lever controls the turn signals,
headlights, and high beams. The
right lever controls the windshield
washers and wipers.
The engine start button and the
remote audio controls are under the
lef t air vent.
The instrument panel brightness
control is in the lower lef t corner of
the speedometer.
The cruise control master switch is
to the lef t of the steering column.To use the horn, press the pad
around the ‘‘H’’ logo.
Controls Near the Steering Wheel
Inst rument s and Cont rols52
HEADLIGHTS/TURN SIGNALS
(P.53)
REMOTE AUDIO
CONTROLS
ENGINE
START
BUTTON
HOOD RELEASE
HANDLE
CRUISE CONTROL MASTER SWITCH WINDSHIELD WIPERS/WASHERS
(P.55) REAR WINDOW
DEFOGGER BUTTON
(P.
57)
INSTRUMENT PANEL BRIGHTNESS
(P.54)
(P.113)
(P.135)
(P.122)
(P.115) HORN

The rotating switch on the lef t lever
controls the lights. Turning this
switch to the ‘‘ ’’ position turns
on the parking lights, taillights,
instrument panel lights, side-marker
lights, and rear license plate lights.
Turning the switch to the ‘‘ ’’
position turns on the headlights.To change f rom low beams to high
beams, push the turn signal lever
f orward until you hear a click. The
blue high beam indicator will light
(see page ). To return to low
beams, pull the turn signal lever
back. If you leave the lights on with the
ignition switch in ACCESSORY (I)
or LOCK (0), you will hear a
reminder tone when you open the
driver’s door.
To f lash the high beams, pull the
turn signal lever back lightly, then
release it. The high beams will come
on and go of f . The high beams will
stay on f or as long as you hold the
lever back, no matter what position
the headlight switch is in.
48
Headlights
Inst rument s and Cont rols
Controls Near the Steering Wheel
53

´µ´µ
µ´
Thedisplaydimswhentheparking
lights or headlights are turned on.
Adjust the brightness to the desired
level with the headlight switch of f ,
and also with the headlight switch on.
Both settings will remain at those
levels until you change them.
The buttons in the lower left corner
of the instrument panel adjust the
brightness of the display in f ive steps.
Push the or button five times
to see the f ull range. With the headlight switch on, you
can switch the display to f ull daytime
brightness by pushing and holding
the button. Push the button to
return the display to the original
brightness.
With the headlight switch off, the
high beam headlights come on with
reduced brightness when you turn
the ignition switch to ON (II) and
release the parking brake. They
remain on until you turn the ignition
of f , even if you set the parking brake.
The headlights revert to normal
operation when you turn them on
with the switch.
Canadian models only
Controls Near the Steering Wheel
Instrument Panel Brightness
Daytime Running L ights
Inst rument s and Cont rols54
BUTTON BUTTON

Keeptheinsideandoutsidemirrors
clean and adjusted f or best visibility.
Be sure to adjust the mirrors bef ore
you start driving.
The inside mirror has day and night
positions. The night position reduces
glare f rom headlights behind you.
Flip the tab on the bottom edge of
the mirror to select the day or night
position.Adjust the outside mirrors with the
adjustment switch on the driver’s
door armrest:
Turn the ignition switch ON (II).
Move the selector switch to L
(driver’s side) or R (passenger’s
side).
Push the red button next to the roof
switch to turn on the hazard warning
lights (f our-way f lashers). This
causes all f our outside turn signals
and both indicators in the instrument
panel to f lash. Use the hazard
warning lights if you need to park in
a dangerous area near heavy traffic,
or if your vehicle is disabled.
1.
2.
Mirrors
Adjusting the Power Mirrors
Hazard Warning
Hazard Warning, Mirrors
Inst rument s and Cont rols80
TAB SELECTOR SWITCH
ADJUSTMENT SWITCH

Push the appropriate edge of the
adjustment switch to move the
mirrorright,left,up,ordown.
When you f inish, move the
selector switch to the center (off)
position. This turns of f the
adjustment switch so you can’t
move a mirror out of position by
accidentally bumping the switch.To apply the parking brake, pull the
lever up f ully. To release it, pull up
slightly, push the button, and lower
the lever. The parking brake light on
the instrument panel should go out
when the parking brake is f ully
released (see page ). If you try to
drive the vehicle without releasing
the parking brake, the ABS indicator
maycomeon,andtheABSmaynot
work properly.
3.
4.
46
Parking Brake
Mirrors, Parking Brake
Inst rument s and Cont rols81
Driving the car with the parking brake
applied can damage the rear brakes
and axles.

Use the MODE control dial to select
the vents the air flows from.Air flows from the vents on
both sides of the instrument panel,
andfromthedashboardventinfront
of the passenger.
When you select , the system
automatically switches to Fresh Air
mode and turns on the A/C.
Air f low is divided between
the vents in the dashboard and the
f loor vents.
Air flows from the center
vents in the dashboard above the
audio system, the vents on both
sides of the instrument panel, and
f rom the f loor vents. Select this
position when you drive with the
convertible top f olded.
Air f lows f rom the f loor
vents and the vents on both sides of
the instrument panel. Air f low is divided between
the f loor vents, the def roster vents at
the base of the windshield, and the
vents on both sides of the instrument
panel.
Air f lows f rom the def roster
vents at the base of the windshield
and the vents on both sides of the
instrument panel.
Heating and Cooling
Comf ort and Convenience Feat ures
Mode Control Dial
87

This section covers how to set up the
system controls f or ventilation,
heating, cooling, dehumidif ying, and
def rosting.
The engine must be running f or the
heater and air conditioning to
generate hot and cold air. The heater
uses engine coolant to warm the air.
If the engine is cold, it will be several
minutes bef ore you f eel warm air
coming from the system.
The air conditioning does not rely on
engine temperature.
You can adjust the direction of the
air coming from the vents on both
sides of the instrument panel and at
the corner of the dashboard on the
passenger’s side. To adjust the air
flow up and down, move the tab in
the center of each vent up and down.
To adjust it lef t and right, turn the
dial under each vent lef t and right. You can shut off the air flow from
each vent by turning the dial all the
way toward the mark until it
clicks.
Heating and Cooling
Comf ort and Convenience Feat ures
Vent Controls
How to Use the System
88
CENTER VENTSIDE VENT

Four controls f or the audio system
areontheleftsideof thedashboard
by the instrument panel. These let
you control basic f unctions without
distracting your attention f rom
driving.
Use the VOLUME lever to adjust the
volume. Push the lever up to
increase the volume and down to
decrease it. Hold the lever until the
volume reaches the desired level,
then release it.If you want to mute the sound
temporarily, push the MUTE button.
The indicator in the button will light
to indicate the mute f unction is on.
Press the button again to cancel
MUTE.
The AUDIO CONTROL button
changes the mode. Pressing the
button repeatedly selects AM, FM1,
FM2, or CD (if a CD is loaded).
The CHANNEL button has two
f unctions, depending on whether you
are listening to the radio, or playing a
CD.
If you are listening to the radio, use
the CHANNEL button to change
stations. Each time you press this
button, the system advances to the
next preset station on the band you
are listening to. You will see the
number of the selected Preset button
in the audio system display.
If youareplayingaCD,thesystem
skips to the beginning of the next
track each time you push the
CHANNEL button.
These controls work only with the
f actory-installed audio system. They
will not f unction if you install any
other system.
Comf ort and Convenience Feat ures
Remote Audio Controls
113
AUDIO CONTROL
BUTTON
CHANNEL
BUTTON
MUTE
BUTTON
VOLUME
LEVER

Press and release the SET/decel
buttononthesteeringwheel.The
CRUISE CONTROL light on the
instrument panel comes on to
show the system is now activated.
Thecruisecontrolmaynothold
the set speed when you are going
up and down hills. If your speed
increases going down a hill, use
thebrakestoslowdowntothe
desired speed. This will cancel thecruise control. To resume the set
speed, press the RESUME/accel
button. The CRUISE CONTROL
light on the instrument panel
comes on.
Press and hold the RESUME/
accel button. The car will
accelerate. When you reach the
desired cruising speed, release the
button.
You can increase the set cruising
speed in any of these ways: You can decrease the set cruising
speed in any of these ways:
Press and hold the SET/decel
button. The car will decelerate.
Release the button when you
reach the desired speed.
To slow down in very small
amounts, tap the SET/decel
button repeatedly. Each time you
do this, your car will slow down
about 1 mph (1.6 km/h).
Tap the brake or clutch pedal
lightly with your f oot. The
CRUISE CONTROL light on the
instrument panel will go out.
When the car slows to the desired
speed, press the SET/decel button.
The car will then maintain the
desired speed.
Push on the accelerator pedal.
Accelerate to the desired cruising
speed and press the SET/decel
button.
To increase your speed in very
small amounts, tap the RESUME/
accel button repeatedly. Each time
you do this, your car will speed up
about 1 mph (1.6 km/h).
3.
Changing t he Set Speed
Cruise Control
Comf ort and Convenience Feat ures116
RESUME/accel
SET/decel

Even with the cruise control turned
on, you can still use the accelerator
pedal to speed up f or passing. Af ter
completing the pass, take your foot
of f the accelerator pedal. The car
will return to the set cruising speed.
Resting your f oot on the brake or
clutch pedal will cause the cruise
control to cancel.Youcancancelthecruisecontrolin
any of these ways:
The system remembers the
previously-set cruising speed. To
return to that speed, accelerate to
above25mph(40km/h),thenpressthe RESUME/accel button. The
CRUISE CONTROL light comes on,
and the car will accelerate to the
same cruising speed as bef ore.
Pressing the Cruise Control Master
Switch turns the system completely
of f and erases the previous cruising
speed f rom memory. To use the
system again, ref er to
.
Press the Cruise Control Master
Switch. Press the SET/decel and
RESUME/accel buttons at the
same time. Tap the brake or clutch pedal.
When you tap the brake or clutch
pedal, or press the SET and
RESUME buttons at the same time,
the CRUISE CONTROL light on the
instrument panel will go out and the
car will begin to slow down. You can
use the accelerator pedal in the
normal way.Cancelling t he Cruise Cont rol
Using t he
Cruise Cont rol
Comf ort and Convenience Feat ures
Cruise Control
117