lock HONDA S2000 2003 1.G Repair Manual

Open the hood.
Remove the electrical connector
f rom the bulb by squeezing the
connector to unlock the tab, then
slide the connector of f the bulb.Remove the rubber weather seal
by pulling on the tab.
If you need to change the high
beam headlight bulb on the lef t
side, remove the coolant reserve
tank f rom its holder by pulling it
straight up. Unclip the end of the hold-down
wire f rom its slot. Pivot it out of
the way and remove the bulb
socket.Install the rubber seal over the
back of the headlight assembly.
Make sure it is right side up; it is
marked ‘‘TOP.’’ Insert the socket back into the
headlight assembly. Make sure
the bulb is installed correctly by
looking through the headlight lens.
The pins on the base of the bulb
should f it in the holes in the
headlight assembly. Pivot the hold-
down wire back in place and clip
the end into the slot.
Pull the bulb straight out of its
socket. Push the new bulb straight
into the socket until it bottoms. Push the electrical connector onto
the new bulb. Turn on the
headlights to test the new bulb.
(Lef t side)
Reinstall the radiator reserve tank.
1.
2. 3.
4.
5.6.
7.
8.
9.
Lights
Maint enance199

If you are changing the bulb on
the driver’s side, start the engine,
turn the steering wheel all the way
to the right, and turn off the
engine. If you are changing the
bulb on the passenger’s side, turn
the steering wheel to the left.Pull the inner f ender cover back.
Remove the socket from the
headlight assembly by turning it
one-quarter turn counterclockwise.
Pull the bulb straight out of its
socket.Install the new bulb in the socket.
Insert the socket back into the
headlight assembly. Turn it
clockwise to lock it in place.
Testthelightstomakesurethe
new bulb is working.
Use a f lat-tipped screwdriver to
remove the three holding clips
f rom the inner f ender.
Put the inner f ender cover in place.
Install the three holding clips.
Lock each clip in place by pushing
on the center.
1.
2.
3.
4.
5.6.
7.
8.
9.
Lights
Maint enance
Replacing Front Turn Signal and
Side Marker L ight Bulbs
200

Pull the bulb straight out of its
socket.
Push the new bulb straight into
the socket until it bottoms.
Put the bulb holder back into its
hole in the lens, and turn it
clockwise until it locks.
Testthelightstomakesurethe
new bulb is working.
Use a small f lat blade screwdriver
to pry caref ully on the back edge
of the side turn signal assembly
until it pops out of the body. Put the side turn signal assembly
back into the body, front first.
Push on the back edge until it
snaps into place.
Turn the bulb holder one-quarter
turn counterclockwise to remove it
from the lens.
1.
2. 3.
4.
5.
6.
Lights
Maint enance
Replacing a Side T urn Signal Bulb
201

Open the trunk.Determine which of the f our bulbs
is burned out: stop/taillight, back-
up light, turn signal, or side
marker.Remove the socket by turning it
one-quarter turn counterclockwise.
Remove the fasteners from the
trunk lining. To remove a f astener,
push on the center of the head
until it pops in. Then pull it out.
Pull the lining back. Remove the burned out bulb. To
remove the stop/taillight, back-up
or side marker light bulb, pull the
bulb straight out of its socket. To
remove the turn signal light bulb,
push it in and turn it
counterclockwise until it unlocks.
1.
2.
3.
4.
5.
6.
Lights
Maint enance
Replacing Rear Bulbs
202

Install the new bulb in the socket.
Testthelightstomakesurethe
new bulb is working. Push the socket into the light
assembly and turn it clockwise
until it locks.Install the trunk lining and secure
it with the fasteners. To reinstall a
f astener, reset the f astener by
pushing on the pointed end until it
pops back almost f lush with the
f ingers on the housing. Put the
f astener in the hole of the trunk
lining and push on the center until
it locks (the center is f lush with
the head).
7.
8.
9.
10.
Lights
Maint enance203

Block the rear wheels.
Disconnect the battery.If possible, run the engine f or a
while periodically (pref erably once
amonth).
Support the f ront wiper blade
arms with a f olded towel or rag so
they do not touch the windshield.
To minimize sticking, apply a
silicone spray lubricant to all door
and trunk seals. Also, apply a
vehiclebodywaxtothepainted
surfaces that mate with the door
and trunk seals.
Fill the f uel tank.
Change the engine oil and f ilter
(see page ).
Wash and dry the exterior
completely.
Cleantheinterior.Makesurethe
carpeting, floor mats, etc. are
completely dry.
If you need to park your car f or an
extended period (more than one
month), there are several things you
should do to prepare it f or storage.
Proper preparation helps prevent
deterioration and makes it easier to
get your car back on the road. If
possible, store your car indoors.
If the car is to be stored for a
longer period, it should be
supported on jackstands so the
tires are of f the ground.
Leave one window open slightly (if
the car is being stored indoors).Coverthecarwitha‘‘breathable’’
cover, one made f rom a porous
material such as cotton.
Nonporous materials, such as
plastic sheeting, trap moisture,
which can damage the paint.
If you store your car f or 12 months
or longer, have your Honda dealer
perf orm the inspections called f or in
the 24 months/30,000 miles (48,000
km) maintenance schedule as soon
as you take it out of storage (see
page ). The replacements called
f or in the maintenance schedule are
not needed unless the car has
actually reached that time or mileage.
Raise the convertible top cover.
Leave the parking brake off. Put
the transmission in Reverse. 163
152
Maint enance
St oring Your Car
206

If you have a f lat tire while driving,
stop in a saf e place to change it.
Stopping in traf f ic or on the shoulder
of a busy road is dangerous. Drive
slowly along the shoulder until you
gettoanexitoranareatostopthat
is far away from the traffic lanes.Open the trunk. Lif t up the tool
box lid and take the jack, wheel
wrench, and extension out of the
tool box.
Thesizedifferencemayalsocause
damage to the rear dif f erential, so do
not mount the compact spare on the
rear. If either rear tire goes f lat,
remove the f ront tire on that same
side, mount the compact spare tire
on the f ront, then mount the f ront
tire on the rear.
Park the car on f irm, level, non-
slippery ground away f rom traf f ic.
Put the transmission in Reverse.
Apply the parking brake.
Turn on the hazard warning lights
and turn the ignition switch to
LOCK (0). Have your passenger
get out of the car while you
change the tire.
Thecompactsparetireissmaller
than a standard tire, which will affect
the vehicle’s handling. Drive
cautiously when this spare is
mounted on your vehicle. 3.
1.
2.
CONT INUED
T aking Care of t he Unexpect ed
Changing a Flat T ire
219
TOOL BOX LID
JACK
The car can easily roll off the
jack, seriously injuring anyone
underneath.
Follow the directions for
changing a tire exactly, and
never get under the car when it
is supported only by the jack. Use the jack that came with your car. If
you try to raise another car with this
jack or use another jack to raise your
car, the car or jack can be damaged.

Unscrew the wing bolt and take
the spare tire out of the spare tire
shelf .
Remove the three clips holding
the spare tire cover by pulling
straight up on the rings. Remove
the spare tire cover.
Loosen the f ive wheel nuts 1/2
turn with the wheel wrench.Locate the jacking point nearest
thetireyouneedtochange.Itis
pointed to by an arrow molded into
the underside of the body. Place
the jack under the jacking point.
Turn the end bracket clockwise
until the top of the jack contacts
the jacking point. Make sure the
jacking point tab is resting in the
jack notch.
4.
5.
6.7.
Changing a Flat T ire
T aking Care of t he Unexpect ed220
SPARETIRECOVER

Look f or any obvious coolant leaks,
such as a split radiator hose.
Everything is still extremely hot,
so use caution. If you f ind a leak, it
must be repaired bef ore you
continue driving (seeon page ). If you don’t f ind an obvious leak,
check the coolant level in the
radiator reserve tank (see page
). If the level is below the
MIN mark, add coolant to halfway
between the MIN and MAX marks. Using gloves or a large heavy
cloth, turn the radiator cap
counterclockwise, without pushing
down, to the f irst stop. This
releases any remaining pressure in
the cooling system. After the
pressure releases, push down on
the cap and turn it until it comes
of f .
If there was no coolant in the
reserve tank, you may also have to
add coolant to the radiator. Let the
engine cool down until the reading
reaches the middle of the
temperature gauge, or lower,
bef ore checking the radiator.
6.
7.9.
8.
245 124
Emergency
Towing
If Your Engine Overheats
T aking Care of t he Unexpect ed230
Removing the radiator cap
while the engine is hot can
cause the coolant to spray out,
seriously scalding you.
Always let the engine and
radiator cool down before
removing the radiator cap.

The auxiliary f use box is located on
thedriver’ssidenearthebrakefluid
reservoir. To open it, push the tab on
each side and remove the lid.If something electrical in your car
stops working, the f irst thing you
should check f or is a blown f use.
Determine f rom the chart on pages
and , or the diagram on the
fuse box lid, which fuse or fuses
control that component. Check those
f uses f irst, but check all the f uses
bef ore deciding that a blown f use is
not the cause. Replace any blown
f uses and check the component’s
operation.
Turn the ignition switch to LOCK
(0). Make sure the headlights and
all other accessories are off.
Remove the cover f rom the f use
box. Check each of the large f uses in
the under-hood f use box by
looking through the top at the wire
inside. Removing these f uses
requires a Phillips-head screw-
driver.
1.
2. 3.
241 242
CONT INUED
Checking and Replacing Fuses
Fuses
T aking Care of t he Unexpect ed239
BLOWN