flat tire HONDA S2000 2008 2.G User Guide

Unscrew the wing bolt, and take
the spare tire out of the spare tire
shelf .
Remove the three clips holding
the spare tire cover by pulling the
rings straight back. Remove the
sparetirecover.
Loosen each wheel nut 1/2 turn
with the wheel nut wrench.Place the jack under the jacking
point nearest the tire you need to
change. Turn the end bracket
clockwise until the top of the jack
contacts the jacking point. Make
sure the center of the jacking
point tab is resting in the jack
notch.
4. 5.
6.7.
Changing a Flat Tire
202
SPARETIRECOVER WHEEL NUT WRENCH
JACKING
POINT
CLIPS
\f—\f—y

y
(\fy\f\fy
2008 S2000

Use the extension and the wheel
nut wrench as shown to raise the
vehicle until the f lat tire is of f the
ground.Bef ore mounting the spare tire,
wipeanydirtoff themounting
surface of the wheel and hub with
a clean cloth. Wipe the hub
carefully;itmaybehotfrom
driving.
Remove the wheel nuts, then
removetheflattire.Handlethe
wheel nuts caref ully; they may be
hot from driving. Place the flat tire
on the ground with the outside
surface facing up.
8. 9. 10.
CONT INUED
Changing a Flat Tire
T aking Care of t he Unexpect ed
203
BRAKE HUB
EXTENSION
\f—\f—y
y
(\fy\f\fy
2008 S2000

Put on the spare tire. Put the
wheel nuts back on f inger-tight,
then tighten them in a crisscross
pattern with the wheel nut wrench
until the wheel is f irmly against
the hub. Do not try to tighten the
wheel nuts f ully.Lower the vehicle to the ground,
and remove the jack.
Tighten the wheel nuts securely in
a crisscross pattern. Have the
wheel nut torque checked at the
nearest automotive service f acility.
Tighten the wheel nuts to:
11. 12. 13.
Changing a Flat Tire
204
80 lbf·ft (108 N·m , 11 kgf·m)
\f—\f—y
y
(\fy\f\fy
2008 S2000

Put the flat tire in the trunk well
vertically as shown.
Remove the tool box f rom the
trunk well, and replace the jack,
wheel wrench, and extension in
the tool box.
Place the tool box into the spare
tire shelf in the trunk.
Replacethesparetirecover.
Secure it with the three clips. Push
each clip in securely, and pivot the
ring down f lat. Your vehicle’s original tire has atire pressure monitoring system
sensor. To replace a tire, ref er to(see
page ). 155
17.
18.
16.
14.
15.
Changing a Flat Tire
Changing a T ire with T PMS
T aking Care of t he Unexpect ed
205
CLIPS
SPARETIRECOVER
TOOL BOX
\f—\f—y
y
(\fy\f
\fy
2008 S2000

If you have a f lat tire while driving,
stop in a saf e place, set the parking
brake, and thoroughly examine the
tire f or a puncture or other damage.
If a puncture is wider than 3/16ths
of an inch (4 mm), or outside of the
tire tread, do not attempt to repair
the tire. Have your vehicle towed to
a Honda service center.
If the damage is smaller than
3/16ths of an inch (4 mm) and
within the tire tread, proceed with
the f ollowing instructions.Position the vehicle so the tire
valve on the flat tire is at the
bottom of the wheel, then remove
the tire valve cap.
When making a temporary repair,
caref ully f ollow all instructions in
this owner’s manual and in the
instructions that came with the kit. The wheel rim is not damaged.
The puncture is located within the
tread.
The puncture is smaller than
3/16ths of an inch (4 mm).
Only one tire is f lat.
To reduce weight, your vehicle is
equipped with a tire repair kit
instead of a spare tire. This kit will
allow you to temporarily repair a f lat
tire under the f ollowing conditions:
1.
CR models only
Repairing a Flat T ire
HowtoUsetheTireRepairKit
206
VALVE CAPTIRE VALVE
\f—\f—y
y
(\fy\f

y
2008 S2000

CONT INUED
Open the trunk and remove the
tire repair kit.Your tire repair kit contains:
An air pump with a power cord
andanairhoseattached. Remove the sealant bottle and
check the expiration date on the
label. If the date has expired, do
not continue. Have your vehicle
towed to the nearest Honda
service center.
If thedatehasnotexpired,shake
the bottle thoroughly and proceed
to step 4.
A bottle of sealant with a f iller
hose attached.
An instruction sheet.
Twolabels,oneforthetirewheel
and one f or the instrument panel. 3.
2.
Repairing a Flat T ire
T aking Care of t he Unexpect ed
207
TOOL BOX LID
TIRE REPAIR KIT EXPIRATION DATE
\f—\f—y
y
(\fy\f
y
2008 S2000

Screw the sealant f iller hose onto
the tire valve. Make sure the
bottle remains upright to ensure
all of the sealant flows into the tire.Unscrew the bottle cap from the
bottle adapter.
Remove the air pump f rom the
repair kit, then screw the air pump
hose onto the bottle adapter.
Make sure the hose is secure.Route the power cord into the
vehicle, and insert the plug into
the accessory power socket.
Turn the ignition switch to the
ACCESSORY (I) position.
4. 5.
6.7.
8.
Repairing a Flat T ire
208
TIRE VALVE
BOTTLE HOSE BOTTLE CAP ADAPTER
AIR PUMP PLUG
ACCESSORY SOCKET
BOTTLE
CAP
AIR PUMP HOSE
\f—\f—y
\fy
(\fy\f
y
2008 S2000

CONT INUED
Turn the air pump switch ON. The
air pressure gauge will show 40 to
60 psi f or the f irst f ew minutes,
then the pressure will go down to
about10to20psi.
Inflate the tire to 32 psi, then turn
the air pump switch OFF. If the air
pressure exceeds 32 psi, push the
def late button until the pressure
reaches the recommended level.
Do not use the air pump f or more
than 15 minutes, or the pump mayoverheat.
Turn the ignition switch to the
LOCK (0) position.
Remove the sealant bottle hose
from the tire valve, then reinstall
the tire valve cap.Push the deflate button on the air
pump until the air pressure gauge
shows 0 psi.
9.
10. 11.
12.13.
Repairing a Flat T ire
T aking Care of t he Unexpect ed
209
AIR PUMP SWITCH
ON DEFLATE BUTTONAIR PRESSURE GAUGE
OFF
\f—\f—y


y
(\fy\f
y
2008 S2000

Remove the wheel label f rom the
repair kit and attach it to the
center of the wheel.Remove the instrument panel label
f rom the repair kit and place it as
shown above.
Remove the power plug f rom the
accessory power socket.
Return all items except the air
pump to the repair kit, and store
the kit in the tool box. Keep the air
pump handy as you will need it
soon.Begin driving at no more than 50
mph (80 km/h).
Af ter 10 minutes, stop saf ely and
use the air pump to check the
pressureinthetire(seepage ).
Your vehicle’s tire has a tire
pressure monitoring system
sensor. To repair a tire with the
tire repair kit, ref er to
(see page ).
14. 15.
16.
17.19.
18.
207
20.
156
Repairing a Flat T ire
Repairing
a T ire with T PMS
210
WHEEL LABEL LABEL
\f—\f—y
\fy
(\fy\f
y
2008 S2000

Remove the tire valve cap, screw the
air pump hose onto the tire valve,
and check the air gauge. (You do not
need to attach the power cord or
turn the air pump switch on.)If the pressure is at 32 psi, continue
driving to the nearest service station.
In any case, be sure to have the
damaged tire permanently repaired
or replaced as soon as possible.
Remember to return the tire sealant
bottle to your Honda service center
f or proper disposal.
If the pressure is lower than 32 psi
and higher than 19 psi, use the air
pump to bring air to the desired level
as described in step 10. Then drive
to the nearest service station.
If the pressure is below 19 psi, do not
continue. Have the vehicle towed
(see page ).
228
Repairing a Flat T ire
T aking Care of t he Unexpect ed
211
AIR PUMP HOSE TIRE VALVE
VALVE CAP
\f—\f—y
y
(\fy\f
y
2008 S2000