change time HUMMER H2 2007 User Guide

Engine Hours:Press the trip information button
until ENGINE HOURS appears on the display.
This mode shows the total number of hours
the engine has run. Pressing and holding the reset
stem located on the instrument cluster for about
four seconds will also display the engine hour
information after the odometer is displayed when
the vehicle is off.
Fuel Information Button
t
(Fuel Information):Press the fuel information
button to scroll through the range, fuel used,
average fuel economy, and the engine oil
life system.
Fuel Range:Press the fuel information button
until RANGE appears on the display. This
mode shows the remaining distance you can drive
without refueling. It is based on fuel economy
and the fuel remaining in the fuel tank. The display
will show LOW if the fuel level is low.The fuel economy data used to determine fuel
range is an average of recent driving conditions.
As your driving conditions change, this data is
gradually updated. Fuel range cannot be reset.
Fuel Used:Press the fuel information button until
FUEL USED appears on the display. This mode
shows the number of gallons or liters of fuel used
since the last reset of this menu item. To reset
the fuel used information, press and hold the select
button for one second while FUEL USED is
displayed.
Average Fuel Economy:Press the fuel
information button until AVG ECON appears on
the display. This mode shows how many miles per
gallon (MPG) or liters per 100 kilometers
(L/100 km) your vehicle is getting based on
current and past driving conditions.
Press and hold the select button for one second
while AVG ECON is displayed to reset the average
fuel economy. Average fuel economy will then
be calculated starting from that point. If the
average fuel economy is not reset, it will be
continually updated each time you drive.
224

This system relies upon receiving specic
information from these stations and only works
when the information is available. In rare cases, a
radio station can broadcast incorrect information
that causes the radio features to work improperly.
If this happens, contact the radio station.
While the radio is tuned to an RDS station, the
station name or call letters display instead of the
frequency. RDS stations can also provide the
time of day, a program type (PTY) for current
programming, and the name of the program being
broadcast.
XM™ Satellite Radio Service
XM™ is a satellite radio service that is based in
the 48 contiguous United States and Canada.
XM™ offers a large variety of coast-to-coast
channels including music, news, sports, talk,
traffic/weather (U.S. subscribers), and children’s
programming. XM™ provides digital quality
audio and text information that includes song title
and artist name. A service fee is required in
order to receive the XM™ service. For more
information, contact XM™; In the U.S. at
www.xmradio.com or call 1-800-852-XMXM (9696)
or in Canada at www.xmradio.ca or call
1-877-GET-XMSR (438-9677).
Playing the Radio
PWR (Power):Press this knob to turn the system
on and off.
oVOLp(Volume):Turn this knob clockwise or
counterclockwise to increase or to decrease the
volume.
INFO (Information):When the ignition is off,
press this knob to display the time.
For RDS, press the INFO knob to change what
appears on the display while using RDS. The
display options are station name, RDS station
frequency, PTY (program type), and the name of
the program (if available).
For XM™ (if equipped), press the INFO knob
while in XM™ mode to retrieve four different
categories of information related to the current
song or channel: Artist, Song Title, Category
or PTY, Channel Number/Channel Name.
To change the default on the display, press the
INFO knob until you see the desired display, then
press and hold the knob until a beep sounds.
The selected display is now the default.
244

©SCAN¨:Press and hold either the SCAN or
the TYPE arrows for more than two seconds
until SCAN displays and a beep sounds. The radio
goes to the next track, plays for 10 seconds,
then goes to the next track. Press either the SCAN
or the TYPE arrows again, to stop scanning.
INFO (Information):Press this knob to see how
long the current track has been playing. ET
and the elapsed time appears on the display. To
change the default on the display, track or elapsed
time, press the knob until you see the desired
display, then press and hold the knob for
two seconds. The radio produces one beep and
the selected display becomes the default.
BAND:Press this button to listen to the radio
when a cassette tape or CD is playing. The
inactive tape or CD remains inside the radio for
future listening.
TAPE DISC:Press this button to play a cassette
tape or CD when listening to the radio. The
inactive tape or CD remains safely inside the radio
for future listening.
Z(Eject):Press this button to eject a CD. Eject
can be activated with either the ignition or radio
off. CDs can be loaded with the radio and ignition
off if this button is pressed rst.
CD Messages
If the CD comes out, it could be for one of the
following reasons:
It is very hot. When the temperature returns to
normal, the CD should play.
You are driving on a very rough road. When the
road becomes smoother, the CD should play.
The CD is dirty, scratched, wet, or
upside down.
The air is very humid. If so, wait about an hour
and try again.
There could have been a problem while burning
the CD.
The label could be caught in the CD player.
If the CD is not playing correctly, for any other
reason, try a known good CD.
If any error occurs repeatedly or if an error
cannot be corrected, contact your dealer. If the
radio displays an error message, write it down
and provide it to your dealer when reporting
the problem.
255

XM™ Satellite Radio Service
XM™ is a satellite radio service that is based in
the 48 contiguous United States and Canada.
XM™ offers a large variety of coast-to-coast
channels including music, news, sports, talk,
traffic/weather (U.S. subscribers), and children’s
programming. XM™ provides digital quality
audio and text information that includes song title
and artist name. A service fee is required in
order to receive the XM™ service. For more
information, contact XM™; In the U.S. at
www.xmradio.com or call 1-800-852-XMXM (9696)
or in Canada at www.xmradio.ca or call
1-877-GET-XMSR (438-9677).
Playing the Radio
PWR (Power):Push this knob to turn the system
on and off.
VOLUME:Turn this knob clockwise or
counterclockwise to increase or to decrease
the volume.
INFO (Information):When the ignition is off,
press this knob to display the time.For RDS, press the INFO knob to change what
displays while using RDS. The display options are
station name, RDS station frequency, PTY
(program type), and the name of the program
(if available).
For XM™ (if equipped), press the INFO knob
while in XM™ mode to retrieve four different
categories of information related to the current
song or channel: Artist, Song Title, Category
or PTY, Channel Number/Channel Name.
To change the default on the display, press the
INFO knob until the desired option displays,
then hold the knob until a beep sounds. The
selected display becomes the default.
AUTO VOL (Automatic Volume):With automatic
volume, the audio system adjusts automatically
to make up for road and wind noise as you drive
by increasing the volume as vehicle speed
increases.
Set the volume at the desired level. Press this
button to select MIN (minimum), MED (medium), or
MAX (maximum). AUTO VOL displays. Each higher
setting provides more volume compensation at
faster vehicle speeds. To turn automatic volume off,
press this button until AUTO VOL OFF displays.
257

To scan all loaded CDs, press and hold either
SCAN arrow for more than four seconds until ALL
CD SCAN displays and a beep sounds. Use
this feature to listen to 10 seconds of the rst track
of each loaded CD. Press either SCAN arrow
again, to stop scanning.
INFO (Information):Press this knob to see how
long the current track has been playing. To
change the default on the display, track or elapsed
time, press the knob until you see the desired
display, then hold the knob until the radio beeps.
The selected display becomes the default.
BAND:Press this button to listen to the radio
when a CD is playing. The inactive CD(s) remains
inside the radio for future listening.Using Song List Mode
The six-disc CD changer has a feature called
song list. This feature is capable of saving 20 track
selections.
To save tracks into the song list feature, perform
the following steps:
1. Turn the CD player on and load it with at least
one CD. See “LOAD CD” listed previously in
this section for more information.
2. Check to see that the CD changer is not in
song list mode. S-LIST should not display.
If S-LIST displays, press the SONG LIST
button to turn it off.
3. Select the desired CD by pressing the
numbered pushbutton and then use the SEEK
or TYPE right arrow to locate the track to
be saved. The track begins to play.
266

If there is a decreased audio signal during CD,
MP3, or DVD play, there could be a soft hissing
noise through the speakers and/or headphones.
If the hissing sound in the wireless headphones
seem excessive, make sure the headphone
batteries are fully charged. A small amount of
hissing is normal.
Battery Replacement
To change the batteries, do the following:
1. Press down on the left earpiece and slide the
battery compartment panel down to expose
the battery compartment.
2. Replace the two AAA batteries in the
compartment. Make sure they are installed
correctly using the diagram on the inside
of the battery compartment.
3. Slide the battery compartment panel back and
then down until the panel closes into the
headphone ear piece.
If the headphones are to be stored for a long
period of time, remove the batteries, and keep
them in a cool, dry place.
Wired Headphones
There is a headphone jack on the left lower side
of the video screen. Use this jack with universal
wired headphones. To adjust the volume, do
the following:
1. Press the power button on the monitor to turn
the video screen on. Briey press the power
button again to toggle between monitor and
DVD control buttons. The appropriate toggle is
monitor. Main menu function icons display.
2. Plug the headphone into the corresponding
jack, located on the bottom left of the video
screen, next to the auxiliary jack.
3. Press the soft key buttons on the monitor,
located under the up and down arrow icons,
to increase or to decrease the volume.
Audio Output
Audio from the DVD player or auxiliary devices
can be heard through the vehicle speakers or the
wireless/wired headphones. The FM Modulator
control has to be set to one of eight frequencies in
order for these devices to be heard through the
vehicle’s speakers. See “FM Modulator Control”
later in this section.
273

A-B:This button is used to repeat predened
sections. Press this button once while the disc is
playing to select the starting position. Press a
second time to select the end position. Press a
third time to turn the function off.
GO:Press this button to access scenes directly
by entering the time/title/chapter.
SUBTITLE:Press this button to switch between
the default language set on the DVD player and up
to any alternate language that could be recorded
on the DVD disc itself. Press this button again
to turn the subtitle function off.
PBC (Playback Control):Press this button to
turn video CD playback control on or off.
ZOOM:Press this button to zoom in on video
images during play or pause modes. Press
and release this button multiple times to increase
the image size in sequence, at 1, 2, or 3 times
of normal size, or ZOOM OFF.
In zoom modes, the direction arrow buttons can be
used to change the zoomed monitor viewing area.RETURNq:Press this button to go back
one step in the RSE On-Screen Display (OSD)
menu and some DVD menus. Press this button
to exit the current menu and to go to the
previous menu.
MUTE
$:Press this button to mute the audio
sound output.
DISP. (Display):Press this button to switch
between display functions of elapsed/remaining
time, full information, or off.
REPEAT
k:Press this button to switch between
repeat functions of title, chapter, track, entire
disc, or off.
AUDIO:Press this button to switch between the
default language set on the DVD player or to
any alternate language that could be recorded on
the DVD disc itself.
Numeric Keys:The numbered buttons located on
the lower left side of the system’s remote control
are numerical digits assigned to menu options.
To use the numeric buttons, follow the menu
instructions by pressing the number that has been
assigned to the preferred option.
283

Battery Replacement
To change the remote control batteries, do the
following:
1. Slide the battery door, located on the back of
the remote control, down.
2. Replace the two AAA batteries in the
compartment. Make sure they are installed
correctly, using the diagram on the inside
of the battery compartment.
3. Close the battery door.
If the remote control is to be stored for a long
period of time, remove the batteries and keep them
in a cool, dry place.
Using the RSE On-Screen
Display (OSD) Menu
To use the RSE OSD menu while using the DVD
player or an auxiliary device, do the following:
1. Press the SETUP button on the system’s
remote control to access the general setup
menu, see “Remote Control” earlier in
this section.
2. Once this menu is on the screen, press the
directional arrows and then the ENTER
button to navigate the screen.
This menu lets you select default preferences
for language, video, audio, and ratings.
Not all DVDs support all of the feature defaults
in the setup menus. If a feature is not
supported, the defaults are provided by the
DVD media.
The default language selection applies to all
future DVDs.
3. Press the RETURN button on the system’s
remote control to exit this menu, or wait for
the menu to time out.
284

Displaying JPEG Images
To use the RSE OSD menu for displaying
JPEG images, do the following:
1. Insert a CD with JPEG images and then
select it for playback from the RSE
on-screen display menu.
A slide show of the images, starting from the
rst picture, automatically begins, or press
PLAY on the system’s remote control to start.
The images change automatically every
10 seconds.
2. Press the directional arrows to see the next or
previous pictures.
3. You can also press the numeric digits on the
system’s remote control to enter the picture
number and then ENTER, to access the
images directly.4. Press MENU on the system’s remote control
to display nine images at one time.
5. Press the directional arrows on the system’s
remote control to select an image to enlarge
and then press ENTER.
If both MP3 and JPEG les are recorded on a
disc, the player offers a choice of which to
play rst. If no choice is made within 10 seconds,
the MP3 les play automatically. The previous
menu can be accessed at any time by pressing
TITLE on the system’s remote control.
Displaying Disc and Video CD Disc Status
To display a disc status, press DISP (display)
on the system’s remote control to show the total
elapsed time and current chapter elapsed time.
To display a video CD disc status, press DISP on
the system’s remote control to show the total
elapsed time and current track elapsed time.
286

Remember: ABS does not change the time you
need to get your foot up to the brake pedal or
always decrease stopping distance. If you get too
close to the vehicle in front of you, you will not have
time to apply your brakes if that vehicle suddenly
slows or stops. Always leave enough room up
ahead to stop, even though you have ABS.
Using ABS
Do not pump the brakes. Just hold the brake
pedal down rmly and let anti-lock work for you.
You may feel the brakes vibrate, or you may notice
some noise, but this is normal.
Braking in Emergencies
With ABS, you can steer and brake at the same
time. In many emergencies, steering can help you
more than even the very best braking.
Traction Control System (TCS)
Your vehicle has a Traction Control System (TCS)
that limits wheel spin. This is especially useful in
slippery road conditions. The system operates only
if it senses that any of the wheels are spinning or
beginning to lose traction. When this happens, the
system applies the brakes to limit wheel spin.
The Traction Control System may operate on dry
roads under some conditions. When this happens,
you may notice a reduction in acceleration or a
pumping sound. This is normal and doesn’t mean
there’s a problem with your vehicle. Examples of
these conditions include hard acceleration in a turn,
an abrupt upshift or downshift of the transmission or
driving on rough roads.
If your vehicle is in cruise control when the TCS
begins to limit wheel spin, the cruise control will
automatically disengage. When road conditions
allow you to safely use it again, you may re-engage
the cruise control. SeeCruise Control on page 183.
309