buttons HUMMER H3 2007 User Guide

4. The indicator light will ash slowly at rst and
then rapidly after Universal Home Remote
successfully receives the frequency signal
from the hand-held transmitter. Release both
buttons.
5. Press and hold the newly-trained Universal
Home Remote button and observe the
indicator light.
If the indicator light stays on continuously,
programming is complete and your device
should activate when the Universal Home
Remote button is pressed and released.
To program the remaining two Universal Home
Remote buttons, begin with Step 2 under
“Programming Universal Home Remote.”
Do not repeat Step 1 as this will erase all of
the programmed channels.
If the indicator light blinks rapidly for
two seconds and then turns to a constant
light, continue with Steps 6 through 8 following
to complete the programming of a rolling-code
equipped device, most commonly, a garage
door opener.6. Locate in the garage, the garage door opener
receiver (motor-head unit). Locate the “Learn”
or “Smart” button. This can usually be
found where the hanging antenna wire is
attached to the motor-head unit.
7. Firmly press and release the “Learn” or
“Smart” button. The name and color of
the button may vary by manufacturer.
You will have 30 seconds to start Step 8.
8. Return to the vehicle. Firmly press and hold
the programmed Universal Home Remote
button for two seconds, then release it.
Immediately press and hold the same button
a second time for two seconds, then
release it. Immediately, press and hold the
same button a third time for two seconds,
then release.
The Universal Home Remote should now
activate your rolling-code equipped device.
To program the remaining two Universal Home
Remote buttons, begin with Step 2 of
“Programming Universal Home Remote.” You
do not want to repeat Step 1, as this will erase
all previous programming from the Universal
Home Remote buttons.
141

Gate Operator and Canadian
Programming
Canadian radio-frequency laws require transmitter
signals to time out or quit after several seconds
of transmission. This may not be long enough
for Universal Home Remote to pick up the signal
during programming. Similarly, some U.S. gate
operators are manufactured to time out in
the same manner.
If you live in Canada, or you are having difficulty
programming a gate operator or garage door
opener by using the “Programming Universal
Home Remote” procedures, regardless of where
you live, replace Step 3 under “Programming
Universal Home Remote” with the following:
Continue to press and hold the Universal Home
Remote button while you press and release every
two seconds (cycle) the hand-held transmitter
button until the frequency signal has been
successfully accepted by the Universal Home
Remote. The Universal Home Remote indicator
light will ash slowly at rst and then rapidly.
Proceed with Step 4 under “Programming
Universal Home Remote” to complete.
Using Universal Home Remote
Press and hold the appropriate Universal Home
Remote button for at least half of a second.
The indicator light will come on while the signal is
being transmitted.
Erasing Universal Home Remote
Buttons
To erase programming from the three Universal
Home Remote buttons do the following:
1. Press and hold down the two outside buttons
until the indicator light begins to ash, after
20 seconds. Do not hold the two outside
buttons for longer than 30 seconds.
2. Release both buttons.
The Universal Home Remote is now in the training
(learning) mode and can be programmed at any
time beginning with Step 2 under “Programming
Universal Home Remote” shown earlier in
this section.
Individual buttons cannot be erased, but they can
be reprogrammed. See “Reprogramming a
Single Universal Home Remote Button” following
this section.
142

The main components of your instrument panel are the following:
A. Air Outlets. SeeOutlet Adjustment on page 173.
B. Turn Signal/Multifunction Lever. SeeTurn
Signal/Multifunction Lever on page 155.
Windshield Washer/Wiper. SeeWindshield
Wipers on page 157andWindshield Washer
on page 158. Cruise Controls. SeeCruise
Control on page 159.
C. Horn. SeeHorn on page 154.
D. Instrument Panel Cluster. SeeInstrument
Panel Cluster on page 175.
E. Hazard Warning Flasher Button. SeeHazard
Warning Flashers on page 154.
F. All-Wheel Drive, Passenger Air Bag Status
Indicator, Locking Rear Axle, and Traction
Control System/StabiliTrak
®Buttons. See
Full-Time Four-Wheel Drive on page 111,
Passenger Airbag Status Indicator on page 179,
Locking Rear Axle on page 243,Traction
Control System (TCS) on page 241and
StabiliTrak
®System on page 244.
G. Exterior Lamps Control, Dome Override Button,
Instrument Panel Brightness Control, Fog Lamp
Button, and OnStar
®Button. SeeExterior LampsLamps on page 162,Dome Lamp Override
on page 168,Instrument Panel Brightness
on page 167,Fog Lamps on page 167, and
OnStar
®System on page 129.
H. Parking Brake Release. SeeParking Brake
on page 116.
I. Audio System. SeeAudio System(s) on
page 201.
J. Climate Control System. SeeClimate Control
System on page 170.
K. Rear Washer/Wiper Control. SeeRear Window
Wiper/Washer on page 159.
L. Off-Road Lamps Buttons. SeeOff-Road Lamps
on page 166.
M. Shift Lever. SeeAutomatic Transmission
Operation on page 106orManual Transmission
Operation on page 109.
N. Accessory Power Outlets. SeeAccessory
Power Outlet(s) on page 169.
O. Glove Box. SeeGlove Box on page 143.
153

Remote Keyless Entry (RKE) Feedback
This feature allows you to program your Remote
Keyless Entry (RKE) feedback to a preferred
setting.
To set your choice for this feature, perform the
following steps:
1. With the engine off, turn the key to LOCK.
Do not remove the key from the ignition.
2. Press and hold the lock and unlock buttons
on the RKE transmitter at the same time.
Hold both buttons until the DIC display shows
the current RKE feedback mode.
3. To view the next available mode, press and
hold the reset stem for about two seconds.
Release the reset stem and press and
hold again to view each mode.
4. Once the desired mode is shown on the DIC
display, briey press the reset stem to set
your choice. The DIC display will then clear.The following are the available modes:
RFA 1 (default):This mode ashes the parking
lamps when you press the lock or unlock
buttons on the RKE transmitter.
RFA 2:This mode ashes the parking lamps and
sounds the horn when you press the lock button
on the RKE transmitter. This mode also ashes the
parking lamps when you press the unlock button
on the RKE transmitter.
RFA 3:This mode ashes the parking lamps
and sounds the horn when you press the lock or
unlock buttons on the RKE transmitter.
RFA 4:This mode disables RKE feedback. There
will be no feedback when you press the lock or
unlock buttons on the RKE transmitter.
195

For XM™ (if equipped), press the DISP button while
in XM™ mode to retrieve four different categories of
information related to the current song or channel:
Artist, Song Title, Category or PTY (program type),
Channel Number/Channel Name.
To change the default on the display, press the
DISP button until you see the desired display, then
hold this knob for two seconds. The radio produces
one beep and the selected display becomes the
default.
AUTO VOL (Automatic Volume):With automatic
volume, the audio system adjusts automatically
to make up for road and wind noise as you drive.
Set the volume at the desired level. Press this
button to select LOW, MEDIUM, or HIGH.
Each higher setting allows for more volume
compensation at faster vehicle speeds. Then as
you drive, automatic volume increases the volume,
as necessary, to overcome noise at any speed.
The volume level should always sound the same
to you as you drive. NONE displays if the radio
cannot determine the vehicle speed. To turn
automatic volume off, press this button until
AVOL OFF displays.Finding a Station
BAND:Press this button to switch between FM1,
FM2, AM, or XM1 or XM2 (if equipped). The
display shows the selection.
e(Tune):Turn this knob to select radio stations.
tSEEKu:Press and release the right or
the left arrow to go to the next or to the previous
station and stay there.
To scan stations, press and hold either arrow
for more than two seconds. SCN displays and the
radio produces one beep. The radio goes to a
station, plays for a few seconds, then goes to the
next station. Press either arrow again or one of
the pushbuttons to stop scanning presets.
To scan preset stations, press and hold either
arrow for more than four seconds. PSC displays
and the radio produces two beeps. The radio
goes to a preset station, plays for a few seconds,
then goes to the next preset station. Press
either arrow again or one of the pushbuttons to
stop scanning presets.
The radio only seeks and scans stations with a
strong signal that are in the selected band.
204

4(Information) (XM™ Satellite Radio Service
and MP3 Features):If the current station
has a message, the information symbol appears
on the display. Press this button to see the
message. The message may display the artist,
song title, call in phone numbers, etc.
If the entire message is not displayed, parts of
the message appears every three seconds.
To scroll through the message, press and release
the information button. A new group of words
appears on the display after every press of this
button. Once the complete message has
displayed, the information symbol disappears
from the display until another new message
is received. The last message can be displayed
by pressing the information button. You can
view the last message until a new message is
received or a different station is tuned to.
When a message is not available from a station,
NO INFO displays.Setting Preset Stations
Up to 30 stations (six FM1, six FM2, and six AM,
six XM1 and six XM2 (if equipped)), can be
programmed on the six numbered pushbuttons,
by performing the following steps:
1. Turn the radio on.
2. Press BAND to select FM1, FM2, AM,
or XM1 or XM2.
3. Tune in the desired station.
4. Press EQ to select the equalization.
5. Press and hold one of the six numbered
pushbuttons until a beep sounds. Whenever
that numbered pushbutton is pressed,
the station that was set returns and the
equalization that was selected is stored
for that pushbutton.
6. Repeat the steps for each pushbutton.
205

tSEEKu:Press and release the right or the
left arrow to go to the next or to the previous
station and stay there.
The radio only seeks stations with a strong
signal that are in the selected band.
Press and hold either arrow for more than
two seconds. SCAN displays and the radio
produces one beep. The radio goes to a station,
plays for a few seconds, then goes to the next
station. Press either arrow again or one of
the pushbuttons to stop scanning presets.
The radio only scans stations with a strong
signal that are in the selected band.
Press and hold this button until PSCN displays
and the radio produces two beeps. The radio
goes to a preset station, plays for a few seconds,
then goes to the next preset station. Press
either arrow again or one of the pushbuttons
to stop scanning presets.
The radio only scans preset stations with a strong
signal that are in the selected band.4(Information) (XM™ Satellite Radio Service):
If the current station has a message, the information
symbol appears on the display. Press this button to
see the message. The message may display the
artist, song title, call in phone numbers, etc.
If the entire message is not displayed, parts of the
message appears every three seconds. To scroll
through the message, press and release the
INFO button. A new group of words appears on the
display after every press of this button. Once the
complete message has displayed, the information
symbol disappears from the display until another
new message is received. The last message can
be displayed by pressing the INFO button. You
can view the last message until a new message
is received or a different station is tuned to.
When a message is not available from a station,
No Info displays.
1-6 (Preset Pushbuttons):Press this button
to play stations that are programmed on the
radio preset pushbuttons.
The radio only seeks preset stations with a
strong signal that are in the selected band.
213

Setting Preset Stations
Up to 30 stations (six FM1, six FM2, and six AM,
six XM1 and six XM2 (if equipped)), can be
programmed on the six numbered pushbuttons,
by performing the following steps:
1. Turn the radio on.
2. Press BAND to select FM1, FM2, AM,
or XM1 or XM2.
3. Tune in the desired station.
4. Press AUTO EQ to select the equalization.
5. Press and hold one of the six numbered
pushbuttons until a beep sounds. Whenever
that numbered pushbutton is pressed,
the station that was set returns and the
equalization that was selected is stored for
that pushbutton.
6. Repeat the steps for each pushbutton.
Setting the Tone (Bass/Treble)
e
(Bass/Treble):Push and release this knob
until BASS or TREB displays. Turn this knob
to increase or to decrease. The display shows the
bass or the treble level. If a station is weak or
has static, decrease the treble.
To adjust the bass and the treble to the middle
position, while in bass or treble, push and hold the
tone knob. The radio produces one beep.
To adjust all tone and speaker controls to the
middle position, push and hold the tone knob
when no tone or speaker control is displayed.
ALL CENTERED displays and a beep sounds.
AUTO EQ (Automatic Equalization):Press this
button to select customized equalization settings
designed for country/western, jazz, talk, pop,
rock and classical.
The equalization one through seven options are
included only if your vehicle is equipped with
the Bose
®system. Press the AUTO EQ button
to select equalization settings designed for
equalization one through seven.
To return the bass and treble to the manual mode,
push and release the tone knob until BASS and
TREB displays.
214

The player will be able to read and play a
maximum of 50 folders, 50 playlists, 10 sessions,
and 255 les. Long le names, folder names,
or playlist names may use more disc memory
space than necessary. To conserve space on the
disc, minimize the length of the le, folder, or
playlist names. You can also play an MP3 CD that
was recorded using no le folders. The system
can support up to 11 folders in depth, though,
keep the depth of the folders to a minimum
in order to keep down the complexity and
confusion in trying to locate a particular folder
during playback. If a CD contains more than the
maximum of 50 folders, 50 playlists, 10 sessions,
and 255 les the player lets you access and
navigate up to the maximum, but all items over
the maximum are ignored.
Root Directory
The root directory is treated as a folder. If the
root directory has compressed audio les,
the directory is displayed as F1 ROOT. All les
contained directly under the root directory
are accessed prior to any root directory folders.
However, playlists (Px) are always accessed
before root folders or les.
Empty Directory or Folder
If a root directory or a folder exists somewhere
in the le structure that contains only folders/
subfolders and no compressed les directly
beneath them, the player advances to the next
folder in the le structure that contains compressed
audio les. The empty folder does not display.
No Folder
When the CD contains only compressed les, the
les are located under the root folder. The next
and previous folder functions does not function
on a CD that was recorded without folders
or playlists. When displaying the name of the
folder the radio displays ROOT.
When the CD contains only playlists and
compressed audio les, but no folders, all les
are located under the root folder. The folder down
and the folder up buttons search playlists (Px)
rst and then go to the root folder. When the
radio displays the name of the folder the radio
displays ROOT.
223

Locking Rear Axle
Your vehicle may have this feature. The locking
rear axle can give your vehicle additional traction
from the rear wheels when traveling in off-road
situations such as mud, snow, sand, steep
hills and uneven terrain.
The button used to turn
this feature on or off is
located to the right
of the transfer case
buttons on the center of
the instrument panel.
To lock the rear axle, do the following:
1. Place the transfer case in the 4LO Lock mode.
This is the only mode which will allow the rear
axle to lock. SeeFull-Time Four-Wheel Drive
on page 111for more information regarding
the transfer case and 4LO Lock mode.
2. Press the button with the vehicle stopped or
moving less than 2 mph (3 km/h).
You must wait for the light in the button to stop
ashing and remain illuminated before the
rear axle is locked.Notice:If you try to lock the rear axle while
your vehicle is stuck and the tires are spinning,
you could damage your vehicle’s drivetrain.
The repairs would not be covered by your
warranty. Always lock the rear axle before
attempting situations and/or navigating terrain
which could possibly cause the vehicle to
become stuck.
The locking rear axle will be disengaged when the
wheel speed is greater than 20 mph (32 km/h),
if the vehicle’s battery is low and/or the transfer
case is shifted out of 4LO Lock mode.
Notice:If you lock the rear axle while driving
on pavement, you could damage your vehicle’s
drivetrain. The repairs would not be covered by
your warranty. Do not use the locking rear axle
on pavement. If you need four-wheel drive when
traveling on pavement, use only 4HI.
243