key HUMMER H3 2009 User Guide

Power Windows
{CAUTION
Leaving children in a vehicle with
the keys is dangerous for many
reasons, children or others could
be badly injured or even killed.
They could operate the power
windows or other controls or
even make the vehicle move.
The windows will function and
they could be seriously injured or
killed if caught in the path of a
closing window. Do not leave
keys in a vehicle with children.
When there are children in the
rear seat use the window lockout
button to prevent unintentional
operation of the windows.The power window controls are
located on each door.
The driver’s door also has passenger
window switches. The ignition must
be in ACC/ACCESSORY, ON/RUN,
or in Retained Accessory Power
(RAP). SeeRetained Accessory
Power (RAP) on page 2-17.
Pull up or press down on the front
edge of the switch to raise or lower
the window.
Express-Down Window
The driver’s window has an
express-down feature that lowers
the window without holding the
switch. Press the front edge of the
switch past the rst position to
activate the express-down mode.
To stop the express-down, pull
up on the switch. To open the
window partway, press the front of
the switch to the rst position
until the window is at the
desired level.
Window Lockout
o(Window Lockout):The
window lockout button is located
in front of the window switches.
This feature disables the
passenger’s window switches
when the button is pressed.
2-10 Features and Controls

Press the button again to turn the
lockout off. A red band on the
side of the button is lit when the
windows are not locked out.
Sun Visors
Pull the visor toward you, or move it
to the side to help reduce glare.
Pull out the extenders for further
coverage.
On a visor with a mirror, lift the
cover to use it.
Theft-Deterrent
Systems
Vehicle theft is big business,
especially in some cities. This
vehicle has theft-deterrent features,
however, they do not make it
impossible to steal.
Content Theft-Deterrent
This vehicle has a content
theft-deterrent alarm system.
The security light is located on the
instrument panel cluster.
To arm the system:
1. Close all the doors.
2. Lock the doors with the Remote
Keyless Entry (RKE) transmitter.
The security light ashes.If the lock button on the RKE
transmitter is pressed, but a door
is open, the doors lock, the lights
may ash and the horn may sound.
Close the open door to arm the
system.
The alarm goes off if a locked
door is not opened using the
RKE transmitter, or by OnStar
®.
A pre-alarm sounds the horn at
reduced intensity for 10 seconds.
Then, the front turn signal lamps
ash for two minutes, and the horn
sounds for two minutes. The alarm
then turns off to save battery power.
Start the engine to turn off the alarm.
The theft-deterrent system does not
activate if the doors are locked with
the key, the manual door lock, or
power door lock switch. The system
can only be activated using the
RKE transmitter, or by OnStar.
SeeOnStar
®System on page 2-39
for additional information. The
vehicle can be started with the
correct key if the alarm has been
set off.
Features and Controls 2-11

To avoid setting off the alarm by
accident:
Lock the vehicle with the manual
door lock lever, the power door
lock switch, or the key, after
the doors are closed.
Unlock the doors by pressing the
unlock button on the RKE
transmitter or by contacting
OnStar. Unlocking a door any
other way activates the alarm.
Press unlock on the RKE
transmitter, start the vehicle with
the correct key, or have OnStar
unlock the doors to turn the alarm
off. The alarm does not stop if
a door is unlocked any other way.
Testing the Alarm
To test the alarm:
1. From inside the vehicle, lock the
doors with the RKE transmitter.
2. Unlock the door with the manual
door lock and open the door.
The pre-alarm should sound
followed by the full alarm about
10 seconds later.
3. Press the unlock button on the
RKE transmitter or start the
engine to turn the alarm off.
If the alarm does not sound but the
lights ash, check to see if the
horn works. The horn fuse could be
blown. To replace the fuse, see
Fuses and Circuit Breakers
on page 5-91.
If the alarm does not sound or
the front turn signal lamps do not
ash, see your dealer/retailer
for service.
Passlock®(U.S. Only)
Passlock®is a passive
theft-deterrent system that enables
fuel if the vehicle is started with
a valid key. If an incorrect key
is used or the ignition lock cylinder
is tampered with, the fuel system
is disabled and the vehicle does
not start.
The security light turns off
approximately ve seconds after
the engine is started. SeeSecurity
Light on page 3-33.
If the engine stalls and the security
light ashes, wait about 10 minutes
until the light stops ashing
before trying to restart the engine.
Release the key from START
as soon as the engine starts.
If the engine does not start after
three tries, the vehicle needs
service.
2-12 Features and Controls

If the engine is running and the
security light comes on, the engine
restarts if you turn the engine
off. However, the Passlock
®system
is not working properly and must
be serviced by your dealer/retailer.
The vehicle is not protected by
Passlock
®at this time. See
your dealer/retailer for service.
In an emergency, call the Roadside
Assistance Center. SeeRoadside
Service on page 7-6.
Do not leave the key or device that
disarms or deactivates the theft
deterrent system in the vehicle.
PASS-Key®III+ Electronic
Immobilizer
The PASS-Key III+ system
operates on a radio frequency
subject to Federal Communications
Commission (FCC) Rules and
with Industry Canada.
This device complies with Part 15
of the FCC Rules. Operation
is subject to the following
two conditions:
1. This device may not cause
harmful interference.
2. This device must accept any
interference received, including
interference that may cause
undesired operation.This device complies with RSS-210
of Industry Canada. Operation
is subject to the following
two conditions:
1. This device may not cause
interference.
2. This device must accept any
interference received, including
interference that may cause
undesired operation of the
device.
Changes or modications to
this system by other than an
authorized service facility could void
authorization to use this equipment.
PASS-Key III+ uses a radio
frequency transponder in the key that
matches a decoder in the vehicle.
Features and Controls 2-13

PASS-Key®III+ Electronic
Immobilizer Operation
(Canada Only)
This vehicle has a passive
theft-deterrent system.
The system is automatically armed
when the key is removed from
the ignition.
The system is automatically
disarmed when the key is turned
to ON/RUN.
You do not have to manually arm or
disarm the system.
The security light comes on if there
is a problem with arming or
disarming the theft-deterrent system.
The key uses a transponder that
matches an immobilizer control unit
in the vehicle. Only the correct
key starts the vehicle. If the key is
ever damaged, the vehicle may
not start.When trying to start the vehicle,
if the engine does not start and
the security light comes on,
there may be a problem with the
theft-deterrent system. Turn the
ignition off and try again.
If the engine still does not start, and
the key appears to be undamaged,
try another ignition key. Check
the fuse. SeeFuses and Circuit
Breakers on page 5-91. If the engine
still does not start with the other
key, the vehicle needs service.
If the vehicle does start, the rst
key may be faulty. See your
dealer/retailer who can service the
theft-deterrent system and have
a new key made.
It is possible for the theft-deterrent
system decoder to learn the
transponder value of a new or
replacement key. Up to 10 keys can
be programmed for the vehicle.
The following procedure is for
programming additional keys only.Canadian Owners:If the keys
are lost or damaged, only a
dealer/retailer can service the
theft-deterrent system to have new
ones made. Two current driver’s
keys are required to program
additional keys.
To program a new key:
1. Verify that the new key has
PK3+ stamped on it.
2. Insert the current driver’s key in
the ignition and start the engine.
If the engine does not start see
your dealer/retailer for service.
3. After the engine has started,
turn the key to LOCK/OFF,
and remove the key.
4. Insert the second current driver’s
key in the ignition and start the
engine within ten seconds of
removing the previous key. If the
engine does not start see your
dealer/retailer for service.
2-14 Features and Controls

5. After the engine has started, turn
the key to LOCK/OFF, and
remove the key. Insert the key to
be programmed and turn it to
ON/RUN within ten seconds of
removing the previous key.
The security light turns off once
the key has been programmed.
6. Repeat the Steps 1 through 5
if additional keys are to be
programmed.
If the security light comes on and
stays on while driving, the engine
will restart if you turn it off. However,
the theft-deterrent system is not
working properly and must be
serviced by your dealer/retailer.
The vehicle is not protected by the
theft-deterrent system at this time.
In an emergency, contact Roadside
Assistance. SeeRoadside Service
on page 7-6.
Do not leave the key or device that
disarms or deactivates the theft
deterrent system in the vehicle.Starting and
Operating Your
Vehicle
New Vehicle Break-In
Notice:The vehicle does
not need an elaborate break-in.
But it will perform better in
the long run if you follow these
guidelines:
Keep your speed at 55 mph
(88 km/h) or less for the
rst 500 miles (805 km).
Do not drive at any one
constant speed, fast or slow,
for the rst 500 miles (805 km).
Do not make full-throttle
starts. Avoid downshifting to
brake or slow the vehicle.
Avoid making hard stops for
the rst 200 miles (322 km)
or so. During this time the
new brake linings are not yet
broken in. Hard stops with new
linings can mean premature
wear and earlier replacement.
Follow this breaking-in
guideline every time you get
new brake linings.
Do not tow a trailer during
break-in. SeeTowing a
Trailer on page 4-42for the
trailer towing capabilities of the
vehicle and more information.
Following break-in, engine
speed and load can be gradually
increased.
Features and Controls 2-15

Ignition Positions
The ignition switch has four different
positions.
To shift out of P (Park), turn the
ignition to ON/RUN and apply
the regular brake pedal.Notice:Using a tool to force the
key to turn in the ignition could
cause damage to the switch or
break the key. Use the correct key,
make sure it is all the way in, and
turn it only with your hand. If the
key cannot be turned by hand, see
your dealer/retailer.
(A) LOCK/OFF:This position
locks the ignition. It also locks
the transmission on automatic
transmission vehicles. It locks
the steering wheel on manual
transmission vehicles. The key can
only be removed in LOCK/OFF.
On vehicles with an automatic
transmission, the shift lever must be
in P (Park) to turn the ignition
switch to LOCK/OFF.
The steering can bind with the
wheels turned off center. If this
happens, move the steering wheel
from right to left while turningthe key to ACC/ACCESSORY.
If this doesn’t work, then the vehicle
needs service.
(B) ACC/ACCESSORY:This is the
position in which you can operate
the electrical accessories or items
plugged into the accessory power
outlets. On automatic transmission
vehicles, this position unlocks
the ignition. On manual transmission
vehicles, it unlocks the ignition
and steering wheel. Use this position
if the vehicle must be pushed or
towed.
(C) ON/RUN:This position can be
used to operate the electrical
accessories and to display some
instrument panel cluster warning
and indicator lights. The switch stays
in this position when the engine is
running. The transmission is
also unlocked in this position on
automatic transmission vehicles.
2-16 Features and Controls

If you leave the key in the
ACC/ACCESSORY or ON/RUN
position with the engine off,
the battery could be drained.
You may not be able to start the
vehicle if the battery is allowed
to drain for an extended period
of time.
(D) START:This is the position that
starts the engine. When the engine
starts, release the key. The ignition
switch returns to ON/RUN for driving.
A warning tone will sound when the
driver door is opened, the ignition
is in ACC/ACCESSORY or
LOCK/OFF and the key is in
the ignition.Retained Accessory
Power (RAP)
These vehicle accessories can be
used for up to 20 minutes after
the engine is turned off:
Audio System
Front Wipers
Power Windows
Sunroof (if equipped)
These features will work when
the key is in ON/RUN or
ACC/ACCESSORY. Once the key is
turned from ON/RUN to LOCK/OFF,
these features continue working
for up to 20 minutes or until a door
is opened.
Starting the Engine
Place the transmission in the
proper gear.
Automatic Transmission
Move the shift lever to P (Park) or
N (Neutral). The engine will not start
in any other position. To restart
the vehicle when it is already
moving, use N (Neutral) only.
Notice:Do not try to shift to
P (Park) if the vehicle is moving.
If you do, you could damage
the transmission. Shift to P (Park)
only when the vehicle is stopped.
Manual Transmission
The shift lever should be in
N (Neutral) and the parking brake
engaged. Hold the clutch pedal
down to the oor and start the
engine. The vehicle will not start
if the clutch pedal is not all the
way down.
Features and Controls 2-17

Starting Procedure
1. With your foot off the accelerator
pedal, turn the ignition key to
START. When the engine starts,
let go of the key. The idle speed
will go down as the engine
warms. Do not race the engine
immediately after starting it.
Operate the engine and
transmission gently to allow
the oil to warm up and lubricate
all moving parts.
The vehicle has a
Computer-Controlled Cranking
System. This feature assists
in starting the engine and
protects components. If the
ignition key is turned to the
START position, and then
released when the engine
begins cranking, the engine
will continue cranking for a
few seconds or until the vehicle
starts. If the engine does not
start and the key is held in
START for many seconds,
cranking will be stopped after15 seconds to prevent cranking
motor damage. To prevent
gear damage, this system also
prevents cranking if the engine
is already running. Engine
cranking can be stopped by
turning the ignition switch
to ACC/ACCESSORY or
LOCK/OFF.
Notice:Cranking the engine for
long periods of time, by returning
the key to the START position
immediately after cranking has
ended, can overheat and damage
the cranking motor, and drain the
battery. Wait at least 15 seconds
between each try, to let the
cranking motor cool down.
2. If the engine does not start
after 5-10 seconds, especially in
very cold weather (below 0°F
or−18°C), it could be ooded
with too much gasoline. Push the
accelerator pedal all the way
to the oor and holding it there
as you hold the key in START
for a maximum of 15 seconds.Wait at least 15 seconds
between each try, to allow the
cranking motor to cool. When the
engine starts, let go of the key
and accelerator. If the vehicle
starts briey but then stops
again, repeat the procedure.
This clears the extra gasoline
from the engine. Do not race
the engine immediately
after starting it. Operate the
engine and transmission gently
until the oil warms up and
lubricates all moving parts.
Notice:The engine is designed
to work with the electronics
in the vehicle. If you add electrical
parts or accessories, you could
change the way the engine
operates. Before adding electrical
equipment, check with your
dealer/retailer. If you do not,
the engine might not perform
properly. Any resulting damage
would not be covered by the
vehicle warranty.
2-18 Features and Controls

It features an electronic shift
position indicator within the
instrument cluster.
There are several different positions
for the shift lever.
P (Park):This position locks the
rear wheels. It is the best position
to use when you start the engine
because the vehicle cannot
move easily.
{CAUTION
It is dangerous to get out of the
vehicle if the shift lever is not fully
in P (Park) with the parking brake
rmly set. The vehicle can roll.
Do not leave the vehicle when the
engine is running unless you have
to. If you have left the engine
running, the vehicle can move
suddenly. You or others could be
injured. To be sure the vehicle will
not move, even when you are on
fairly level ground, always set the
parking brake and move the shift
lever to P (Park). SeeShifting Into
Park (Automatic Transmission) on
page 2-29. If you are pulling a
trailer, seeTowing a Trailer on
page 4-42.
Make sure the shift lever is fully in
P (Park) before starting the engine.
The vehicle has an automatic
transmission shift lock controlsystem. You must fully apply the
regular brakes rst and then press
the shift lever button before you
can shift from P (Park) when
the ignition key is in ON/RUN. If you
cannot shift out of P (Park), ease
pressure on the shift lever and push
the shift lever all the way into
P (Park) as you maintain brake
application. Then press the
shift lever button and move the shift
lever into another gear. See
Shifting Out of Park (Automatic
Transmission) on page 2-30
R (Reverse):Use this gear to
back up.
Notice:Shifting to R (Reverse)
while the vehicle is moving
forward could damage the
transmission. The repairs would
not be covered by the vehicle
warranty. Shift to R (Reverse)
only after the vehicle is stopped.
2-20 Features and Controls