wheel HUMMER H3 2009 Manual Online

6. Turn the wheel wrench clockwise
to raise the jack head to the
lifting point.
{CAUTION
Getting under a vehicle when it is
jacked up is dangerous. If the
vehicle slips off the jack, you
could be badly injured or killed.
Never get under a vehicle when it
is supported only by a jack.
{CAUTION
Raising your vehicle with the jack
improperly positioned can damage
the vehicle and even make the
vehicle fall. To help avoid
personal injury and vehicle
damage, be sure to t the jack lift
head into the proper location
before raising the vehicle.7. Remove all the wheel nuts and
take off the at tire.
{CAUTION
Rust or dirt on a wheel, or on the
parts to which it is fastened, can
make wheel nuts become loose
after time. The wheel could come
off and cause an accident. When
changing a wheel, remove any
rust or dirt from places where the
wheel attaches to the vehicle.
In an emergency, use a cloth or a
paper towel to do this; but be sure
to use a scraper or wire brush
later, if needed, to get all the rust
or dirt off. SeeChanging a Flat
Tire on page 5-66.8. Remove any rust or dirt from the
wheel bolts, mounting surfaces
and spare wheel.{CAUTION
Never use oil or grease on bolts
or nuts because the nuts might
come loose. The vehicle’s wheel
could fall off, causing a crash.
9. Put the spare tire on the
mounting surface.
10. Put the wheel nuts back on
with the rounded end of the
nuts toward the wheel
after mounting the spare.
5-74 Service and Appearance Care

11. Tighten each wheel nut by
hand. Then use the wheel
wrench to tighten the nuts
until the wheel is held
against the hub.
12. Turn the wheel wrench
counterclockwise to lower
the vehicle. Lower the jack
completely.
{CAUTION
Incorrect or improperly tightened
wheel nuts can cause the wheel
to come loose and even come off.
This could lead to a crash. If you
have to replace them, be sure to
get new original equipment wheel
nuts. Stop somewhere as soon
as you can and have the nuts
(Continued)
CAUTION (Continued)
tightened with a torque wrench to
the proper torque specication.
SeeCapacities and Specifications
on page 5-96for wheel nut torque
specication.
Notice:Improperly tightened
wheel nuts can lead to brake
pulsation and rotor damage.
To avoid expensive brake repairs,
evenly tighten the wheel nuts
in the proper sequence and to
the proper torque specication.
SeeCapacities and Specifications
on page 5-96for the wheel nut
torque specication.13. Tighten the nuts rmly in a
crisscross sequence as
shown by turning the wheel
wrench clockwise.
14. After installing the wheel and
tire, reinstall the center cap.
Place the cap on the wheel and
tap it into place until it sits
ush with the wheel.
Service and Appearance Care 5-75

5. Turn the lug wrench clockwise to
raise the jack until it lifts the
secondary latch spring.
6. Keep raising the jack until the
spare tire stops moving upward
and is held rmly in place.
This lets you know that the
secondary latch has released
and the spare tire is balancing on
the jack.
7. Lower the jack by turning the
lug wrench counterclockwise.
Keep lowering the jack until the
spare tire slides off the jack.8. Disconnect the lug wrench from
the jack and carefully remove
the jack. Use one hand to push
against the spare tire while
rmly pulling the jack out from
under the spare tire with the
other hand.9. Tilt the retainer and slip it
through the wheel opening when
the spare tire has been
completely lowered.
10. Turn the lug wrench clockwise
to raise the cable back up if the
cable is hanging.
Have the hoist shaft assembly
inspected as soon as you can.
You will not be able to store a spare
tire using the hoist assembly until
it has been repaired or replaced.
Service and Appearance Care 5-77

Storing a Flat or Spare
Tire and Tools (H3)
{CAUTION
Storing a jack, a tire, or other
equipment in the passenger
compartment of the vehicle could
cause injury. In a sudden stop or
collision, loose equipment could
strike someone. Store all these in
the proper place.To store the at or spare tire on the
spare tire mount:
1. Slide the at or spare tire onto
the swing-gate.
You may need assistance
to do this.
2. Reinstall the nuts to retain the
at or spare tire.
3. Tighten the nuts by hand.
{CAUTION
Incorrect or improperly tightened
wheel nuts can cause the wheel
to come loose and even come off.
This could lead to a crash. If you
have to replace them, be sure to
get new original equipment wheel
nuts. Stop somewhere as soon as
you can and have the nuts
tightened with a torque wrench to
the proper torque specication.
SeeCapacities and Specifications
on page 5-96for wheel nut torque
specication.
5-78 Service and Appearance Care

4. Use the wheel wrench to tighten
the nuts rmly. Try to move the
tire back and forth slightly to
be sure it is secure.
5. Reinstall the center tire cover
onto the spare or at tire.
6. If the vehicle has a spare tire
cover close the cover and
latch the side latch.To store the jack tool bag and jack:
1. Return the tools to the jack
tool bag.
2. Secure the tool bag to the jack
by securely wrapping the straps
around the jack. Then, slide
the straps through the rings on
the bag and secure.
3. Position the jack and jack tool
bag in the swing-gate.
When reinstalling the jack and
jack tool bag, make sure the jack
base is securely seated behind
the tabs in the swing-gate.4. Reinstall the wing nut retainer to
fasten the jack and tool bag in
the storage compartment.
Make sure that the wing nut
passes through the tool bag and
the jack before tightening it.
5. Turn the wing nut retainer
clockwise to secure.
6. Reinstall the compartment cover
by inserting the locator tabs in
the holes in the swing-gate.
Push the latches down to secure.
Service and Appearance Care 5-79

Storing a Flat or Spare
Tire and Tools (H3T)
{CAUTION
Storing a jack, a tire, or other
equipment in the passenger
compartment of the vehicle could
cause injury. In a sudden stop or
collision, loose equipment could
strike someone. Store all these in
the proper place.
A. Spare Tire/Flat Tire
(Valve Stem Pointed Down)
B. Tire/Wheel Retainer
C. Hoist Cable
D. Hoist Assembly
E. Hoist Shaft
F. Jack Handle Extension(s)
G. Wheel Wrench
H. Hoist Shaft Access Ramp
I. Hoist End of the Extension ToolTo store the at or spare tire on the
spare tire mount:
1. Place the at or spare tire (A) on
the ground at the rear of the
vehicle with the valve stem
pointed down and to the rear.
2. Tilt the tire. Separate the
tire/wheel retainer (B) from the
guide pin. Pull the pin through
5-80 Service and Appearance Care

the center of the wheel. Tilt the
tire/wheel retainer (B) down
through the center wheel opening.
3. Make sure the tire/wheel
retainer (B) is fully seated across
the underside of the wheel.
4. Assembly the two jack handle
extensions (F) and wheel
wrench (G).5. Insert the hoist end of the
extension tool (I) through
the hoist shaft access ramp (H).
6. Raise the tire part upward.
Make sure the tire/wheel
retainer (B) is seated in the
wheel opening.7. Raise the tire fully against the
underside of the vehicle by
turning the wheel wrench
clockwise until you hear
two clicks or feel it skip twice.
You cannot overtighten the cable.
8. Push, pull (A) and then try to
turn (B) the tire. If the tire
moves, use the wheel wrench
to tighten the cable.
Service and Appearance Care 5-81

To store the jack tool bag and jack:
1. Return the tools to the jack
tool bag.
2. Secure the tool bag to the jack
by securely wrapping the straps
around the jack. Then, slide
the straps through the rings on
the bag and secure.
3. Reinstall the wing nut retainer to
fasten the jack and tool bag
under the rear seat.
Make sure that the wing nut
passes through the tool bag and
the jack before tightening it.
4. Turn the wing nut retainer
clockwise to secure.Spare Tire
The vehicle, when new, had a
fully-inated spare tire. A spare tire
may lose air over time, so check
its ination pressure regularly.
SeeInflation - Tire Pressure on
page 5-51andLoading the Vehicle
on page 4-35for information
regarding proper tire ination and
loading your vehicle. For instruction
on how to remove, install or store
a spare tire, seeRemoving the Flat
Tire and Installing the Spare Tire
on page 5-72andStoring a Flat or
Spare Tire and Tools (H3) on
page 5-78orStoring a Flat or Spare
Tire and Tools (H3T) on page 5-80.
After installing the spare tire on
your vehicle, you should stop
as soon as possible and make sure
the spare is correctly inated.The spare tire does not have a Tire
Pressure Monitor System sensor.
You may get a low pressure warning
light. SeeTire Pressure Monitor
Operation on page 5-54. Have the
damaged or at road tire repaired or
replaced as soon as you can.
Do not mix tires and wheels of
different sizes, because they will not
t. Keep your spare tire and its
wheel together.
5-82 Service and Appearance Care

Aluminum or
Chrome-Plated Wheels
and Trim
The vehicle may have either
aluminum or chrome-plated wheels.
Keep the wheels clean using a soft
clean cloth with mild soap and water.
Rinse with clean water. After rinsing
thoroughly, dry with a soft clean
towel. A wax may then be applied.
Notice:Chrome wheels and
other chrome trim may be
damaged if the vehicle is not
washed after driving on roads
that have been sprayed with
magnesium, calcium or sodium
chloride. These chlorides are
used on roads for conditions
such as ice and dust. Always
wash the vehicle’s chrome with
soap and water after exposure.Notice:Using strong soaps,
chemicals, abrasive polishes,
cleaners, brushes, or cleaners
that contain acid on aluminum or
chrome-plated wheels, could
damage the surface of the
wheel(s). The repairs would not
be covered by the warranty.
Use only approved cleaners on
aluminum or chrome-plated
wheels.
The surface of these wheels is
similar to the painted surface of the
vehicle. Do not use strong soaps,
chemicals, abrasive polishes,
abrasive cleaners, cleaners with
acid, or abrasive cleaning brushes
on them because they could
damage the surface. Do not use
chrome polish on aluminum wheels.Notice:Using chrome polish on
aluminum wheels could damage
the wheels. The repairs would not
be covered by the warranty.
Use chrome polish on chrome
wheels only.
Use chrome polish only on
chrome-plated wheels, but avoid
any painted surface of the wheel,
and buff off immediately after
application.
Notice:Driving the vehicle
through an automatic car wash
that has silicone carbide tire
cleaning brushes, could damage
the aluminum or chrome-plated
wheels. The repairs would not be
covered by the warranty. Never
drive a vehicle equipped with
aluminum or chrome-plated
wheels through an automatic car
wash that uses silicone carbide
tire cleaning brushes.
5-88 Service and Appearance Care

Capacities and Specications (cont’d)
ApplicationCapacities
English Metric
Transfer Case 1.6 qt1.5 L
Transmission (Drain and Rell) 3.7L L5 and 5.3L V8, Automatic Transmission 5.0 qt4.7 L
3.7L L5, Manual Transmission 2.5 qt2.4 L
Wheel Nut Torque 100 lb ft140Y
All capacities are approximate. When adding, be sure to ll to the approximate level, as recommended in this
manual.
Engine Specications
Engine VIN CodeTransmission Spark Plug Gap
3.7L L5 EAutomatic
Manual .040 in (1.01 mm)
5.3L V8 LAutomatic .040 in (1.01 mm)
Service and Appearance Care 5-97