fuses HUMMER H3 2009 Owners Manual
[x] Cancel search | Manufacturer: HUMMER, Model Year: 2009, Model line: H3, Model: HUMMER H3 2009Pages: 382, PDF Size: 1.99 MB
Page 4 of 382
Vehicle Symbol Chart
Here are some additional symbols
that may be found on the vehicle
and what they mean. For more
information on the symbol, refer to
the index.
9:Airbag Readiness Light
#:Air Conditioning
!:Antilock Brake System (ABS)
g:Audio Steering Wheel Controls
or OnStar®
$:Brake System Warning Light
":Charging System
I:Cruise Control
B:Engine Coolant Temperature
O:Exterior Lamps
#:Fog Lamps
.:Fuel Gage
+:Fuses
i:Headlamp High/Low-Beam
Changer
j:LATCH System Child Restraints
*:Malfunction Indicator Lamp
::Oil Pressure
}:Power
/:Remote Vehicle Start
>:Safety Belt Reminders
7:Tire Pressure Monitor
F:Traction Control
M:Windshield Washer Fluid
iv Preface
Page 78 of 382
To avoid setting off the alarm by
accident:
Lock the vehicle with the manual
door lock lever, the power door
lock switch, or the key, after
the doors are closed.
Unlock the doors by pressing the
unlock button on the RKE
transmitter or by contacting
OnStar. Unlocking a door any
other way activates the alarm.
Press unlock on the RKE
transmitter, start the vehicle with
the correct key, or have OnStar
unlock the doors to turn the alarm
off. The alarm does not stop if
a door is unlocked any other way.
Testing the Alarm
To test the alarm:
1. From inside the vehicle, lock the
doors with the RKE transmitter.
2. Unlock the door with the manual
door lock and open the door.
The pre-alarm should sound
followed by the full alarm about
10 seconds later.
3. Press the unlock button on the
RKE transmitter or start the
engine to turn the alarm off.
If the alarm does not sound but the
lights ash, check to see if the
horn works. The horn fuse could be
blown. To replace the fuse, see
Fuses and Circuit Breakers
on page 5-91.
If the alarm does not sound or
the front turn signal lamps do not
ash, see your dealer/retailer
for service.
Passlock®(U.S. Only)
Passlock®is a passive
theft-deterrent system that enables
fuel if the vehicle is started with
a valid key. If an incorrect key
is used or the ignition lock cylinder
is tampered with, the fuel system
is disabled and the vehicle does
not start.
The security light turns off
approximately ve seconds after
the engine is started. SeeSecurity
Light on page 3-33.
If the engine stalls and the security
light ashes, wait about 10 minutes
until the light stops ashing
before trying to restart the engine.
Release the key from START
as soon as the engine starts.
If the engine does not start after
three tries, the vehicle needs
service.
2-12 Features and Controls
Page 80 of 382
PASS-Key®III+ Electronic
Immobilizer Operation
(Canada Only)
This vehicle has a passive
theft-deterrent system.
The system is automatically armed
when the key is removed from
the ignition.
The system is automatically
disarmed when the key is turned
to ON/RUN.
You do not have to manually arm or
disarm the system.
The security light comes on if there
is a problem with arming or
disarming the theft-deterrent system.
The key uses a transponder that
matches an immobilizer control unit
in the vehicle. Only the correct
key starts the vehicle. If the key is
ever damaged, the vehicle may
not start.When trying to start the vehicle,
if the engine does not start and
the security light comes on,
there may be a problem with the
theft-deterrent system. Turn the
ignition off and try again.
If the engine still does not start, and
the key appears to be undamaged,
try another ignition key. Check
the fuse. SeeFuses and Circuit
Breakers on page 5-91. If the engine
still does not start with the other
key, the vehicle needs service.
If the vehicle does start, the rst
key may be faulty. See your
dealer/retailer who can service the
theft-deterrent system and have
a new key made.
It is possible for the theft-deterrent
system decoder to learn the
transponder value of a new or
replacement key. Up to 10 keys can
be programmed for the vehicle.
The following procedure is for
programming additional keys only.Canadian Owners:If the keys
are lost or damaged, only a
dealer/retailer can service the
theft-deterrent system to have new
ones made. Two current driver’s
keys are required to program
additional keys.
To program a new key:
1. Verify that the new key has
PK3+ stamped on it.
2. Insert the current driver’s key in
the ignition and start the engine.
If the engine does not start see
your dealer/retailer for service.
3. After the engine has started,
turn the key to LOCK/OFF,
and remove the key.
4. Insert the second current driver’s
key in the ignition and start the
engine within ten seconds of
removing the previous key. If the
engine does not start see your
dealer/retailer for service.
2-14 Features and Controls
Page 125 of 382
Have the bulbs replaced. If the bulb
is not burned out, check the fuse.
For bulb replacement, see
Taillamps, Turn Signal, Stoplamps
and Back-up Lamps (H3) on
page 5-42orTaillamps, Turn Signal,
Stoplamps and Back-up Lamps
(H3T) on page 5-42. For a blown
fuse or circuit breaker, see
Fuses and Circuit Breakers on
page 5-91.
Turn Signal On Chime
If a turn signal is left on for more
than 3/4 of a mile (1.2 km), a chime
will sound at each ash of the
turn signal and the message TURN
SIGNAL will also appear in the
DIC. To turn the chime and
message off, move the turn signal
lever to the off position.
See “TURN SIGNAL” underDIC
Warnings and Messages on
page 3-37DIC Warnings and
Messages for more information.Headlamp
High/Low-Beam Changer
23
Headlamp High/Low
Beam Changer:Push the turn
signal/multifunction lever away from
you to turn the high beams on.
Pull the lever towards you to return
to low beams.
This indicator light turns on in the
instrument panel cluster when
the high beam headlamps are on.
Flash-to-Pass
This feature lets you use the
high-beam headlamps to signal a
driver in front of you that you want to
pass. It works even if the headlamps
are in the automatic position.
To use it, pull the turn signal lever
toward you, then release it.If the headlamps are in the
automatic position or on low beam,
the high-beam headlamps will
turn on. They will stay on as long as
the lever is held toward you. The
high-beam indicator on the
instrument panel cluster will come
on. Release the lever to return
to normal operation.
Windshield Wipers
The windshield wipers are controlled
by turning the band with
Non it.
8(Mist):Turn to mist for a single
wiping cycle. Hold it there until
the wipers start. Then let go. The
wipers will stop after one wipe. Hold
the band on mist longer, if more
wipes are needed.
N(Delay):The wiper speed can
be set for long or short delays
between wipes. This can be very
useful in light rain or snow. Turn the
band to choose the delay time.
The closer to the top of the lever,
the shorter the delay.
Instrument Panel 3-7
Page 136 of 382
Accessory Power
Outlet(s)
The accessory power outlets can be
used to connect auxiliary electrical
equipment, such as a cellular phone.
There are two accessory power
outlets located under the climate
control system. There is also one
accessory power outlet located in the
rear cargo area (H3 model only). Pull
down the small cover to access the
accessory power outlet.
Notice:Leaving electrical
equipment on for extended
periods will drain the battery.
Always unplug electrical
equipment when not in use and
do not plug in equipment that
exceeds the maximum amperage
rating of 20 amperes.
Certain electrical accessories may
not be compatible with the
accessory power outlet and could
result in blown vehicle or adapter
fuses. If you experience a problem,see your dealer/retailer for additional
information on accessory power
outlets.
Notice:Adding any electrical
equipment to the vehicle can
damage it or keep other
components from working as
they should. The repairs would
not be covered by the vehicle
warranty. Do not use equipment
exceeding maximum amperage
rating of 20 amperes. Check with
your dealer/retailer before
adding electrical equipment.
When adding electrical equipment,
be sure to follow the proper
installation instructions included with
the equipment.
Notice:Improper use of the
power outlet can cause damage
not covered by the warranty.
Do not hang any type of
accessory or accessory bracket
from the plug because the
power outlets are designed for
accessory power plugs only.
Ashtray(s) and Cigarette
Lighter
For vehicles with a removable
ashtray, it can be placed into the
cupholder and be removed for
cleaning.
Notice:If papers, pins, or other
ammable items are put in
the ashtray, hot cigarettes or
other smoking materials could
ignite them and possibly damage
the vehicle. Never put ammable
items in the ashtray.
For vehicles with a lighter, push the
lighter down and it will pop up
when it is ready to be used.
Notice:Holding a cigarette
lighter in while it is heating does
not let the lighter back away from
the heating element when it is hot.
Damage from overheating can
occur to the lighter or heating
element, or a fuse could be blown.
Do not hold a cigarette lighter in
while it is heating.
3-18 Instrument Panel
Page 239 of 382
Electrical System
Add-On Electrical
Equipment.......................5-91
Windshield Wiper Fuses. . . .5-91
Power Windows and
Other Power Options.......5-91
Fuses and Circuit
Breakers.........................5-91
Engine Compartment
Fuse Block......................5-92
Capacities and
Speci cations
Capacities and
Speci cations..................5-96
Service
For service and parts needs, visit
your dealer/retailer. You will receive
genuine GM parts and GM-trained
and supported service people.
Genuine GM parts have one
of these marks:
Accessories and
Modi cations
When non-dealer/non-retailer
accessories are added to the
vehicle, they can affect vehicle
performance and safety, including
such things as airbags, braking,
stability, ride and handling,
emissions systems, aerodynamics,
durability, and electronic systems
like antilock brakes, traction control,
and stability control. Some of
these accessories could even cause
malfunction or damage not
covered by the vehicle warranty.
Damage to vehicle components
resulting from the installation or use
of non-GM certi ed parts, including
control module modi cations,
are not covered under the terms of
the vehicle warranty and may
affect remaining warranty coverage
for affected parts.
Service and Appearance Care 5-3