clock HYUNDAI ELANTRA 2021 User Guide

08
8-21
WARNING
If your vehicle is equipped with a
rollover sensor, place the ignition
switch in the LOCK/OFF or ACC position
when the vehicle is being towed.
The side impact and curtain air bag
may deploy if the sensor detects the
situation as a rollover.
OCN7070095L
When towing your vehicle in an
emergency without wheel dollies:
1.
Place the ignition swit
ch in the ACC
position.
2.
Place the shift button in N (N

eutral).
3.
Release the parking br

ake.
CAUTION
Failure to place the shift button in N
(Neutral) when being towed with the
front wheels on the ground can cause
internal damage to the transmission.
Emergency Towing
If towing is necessary, we recommend
you have it done by an authorized
HYUNDAI dealer or a commercial tow
truck service.
Removable towing hook
OCN7070013
1. Open the trunk, and remo ve the
towing hook from the tool case.
OCN7070014
2. Remove the hole cover by pressing
the lo wer part of the cover on the
bumper.
3.
Install the t

owing hook by turning it
clockwise into the hole until it is fully
secured.
4.
Remo

ve the towing hook and install
the cover after use.

Maintenance
9-52
OCN7080042
1. Open the hood.
2.
Disconnect the negativ
e battery
cable.
3.
Remo

ve the headlamp bulb cover by
turning it counterclockwise.
4.
Disconnect the headlamp bulb
socke

t-connector.
5.
Unsnap the headlamp bulb re

taining
wire by pressing the end and pushing
it upward.
6.
Remo

ve the bulb from the headlamp
assembly.
7.
Install a ne

w headlamp bulb and snap
the headlamp bulb retaining wire into
position by aligning the wire with the
groove on the bulb.
8.
Connect the headlamp bulb socke

t-
connector.
9.
Install the headlamp bulb co

ver by
turning it clockwise.
Information
The headlamp aiming should be adjusted
after an accident or after the headlamp
assembly is reinstalled at an authorized
HYUNDAI dealer. Headlamp/Daytime running light (DRL) /
Parking lamp (LED type)
If the lamp (LED) does not operate, have
the system checked by an authorized
HYUNDAI dealer.
The LED lamps cannot be replaced as
a single unit because it is an integrated
unit. The LED lamps have to be replaced
with the unit.
A skilled technician should check or
repair the LED lamp, for it may damage
related parts of the vehicle.

09
9-53
OCN7080043
Turn signal lamp (Bulb type)
1.
Open the hood.
2.
Disconnect the negativ

e battery
cable.
3.
Remo

ve the socket from
the assembly by turning the
socketcounterclockwise until the
tabs on the socket align with the slots
onthe assembly.
4.
Remo

ve the bulb from the socket
by pressing it in and rotating
itcounterclockwise until the tabs on
the bulb align with the slots in the
socket. Pull the bulb out of the socket.
5.
Insert a new bulb b

y inserting it into
the socket and rotating it until it locks
into place.
6.
Install the sock

et in the assembly by
aligning the tabs on the socket with
the slots in the assembly.
7.
Push the socke

t into the assembly and
turn the socket clockwise.
OCN7090017N
Side marker (Bulb type)
1.
Open the hood.
2.
Disconnect the negativ

e battery
cable.
3.
Remo

ve the socket from the
assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on the
assembly.
4.
Remo

ve the bulb from the socket by
pulling out the bulb.
5.
Insert a new bulb.
Side marker

(LED type)
If the LED lamp does not operate, have
the vehicle checked by an authorized
HYUNDAI dealer.

09
9-55
Tail/Stop lamp/Turn signal lamp/
Side marker (Outer lamp) (Bulb type)
1. Open the trunk lid.
OCN7080045
2. Remove the service cover by pulling
out the service cover.
OCN7080046
3. Loosen the assembly retaining nuts.
OCN7080047
4. Remove the rear combination light
assembly from the body of the
vehicle.
OCN7080075L
OCN7090019N
[A] : Tail/Stop lamp, [B] : Turn signal lamp,
[C] : Rear side marker
5. Remove the socket from the
assembly b y turning the socket
counterclockwise until the tabs on
the socket align with the slots on the
assembly.
6.
Remo

ve the bulb from the socket
by pressing it in and rotating it
counterclockwise until the tabs on the
bulb align with the slots in the socket.
Pull the bulb out of the socket.
7.
Insert a new bulb b

y inserting it into
the socket and rotating it until it locks
into place.
8.
Install the sock

et in the assembly by
aligning the tabs on the socket with
the slots in the assembly. Push the
socket into the assembly and turn the
socket clockwise.

Maintenance
9-56
Tail lamp (Bulb type)
1. Open the trunk.
2.
Loosen the r
etaining screw of the
trunk lid cover and then remove the
cover.
OCN7080040
3. Remove the socket from the
assembly b y turning the socket
counterclockwise until the tabs on
the socket align with the slots on the
assembly.
4.
Remo

ve the bulb by pulling it out.
5.
Insert a new bulb b

y inserting it into
the socket.
6.
Reins

tall the trunk lid cover by
pushing in the screw.
Reverse lamp (Inner lamp)
(Bulb type)
1. Disconnect the connector and then
r emove the nuts by turning the nuts
counter clockwise.
2.
Tak

e the light assembly out.
OCN7080053
3. Remove the socket from the
assembly b y turning the socket
counterclockwise until the tabs on
the socket align with the slots on the
assembly.
4.
Remo

ve the bulb by pulling it out.
5.
Insert a new bulb b

y inserting it into
the socket.
6.
Install the ligh

t assembly to the trunk.
7.
Reins

tall the trunk lid cover by
pushing in the screw.
Stop/Tail lamp and rear side marker
(LED type)
If the LED lamp does not operate, we
recommend that you have the vehicle
checked by an authorized HYUNDAI
dealer.

09
9-57
High mounted stop lamp
replacement
OCN7080032
OAD075042[A] : High mounted stop lamp
1. Open the trunk.
2.
Remo
ve the socket by turning it
counterclockwise until the tabs on the
socket align with the slots.
3.
Remo

ve the bulb from the socket
by pressing it in and rotating it
counterclockwise until the tabs on the
bulb align with the slots in the socket.
Pull the bulb out of the socket.
4.
Insert a new bulb b

y inserting it into
the socket and rotating it until it locks
into place.
5.
Install the sock

et in the assembly by
aligning the tabs on the socket with
the slots in the assembly.
Push the socket into the assembly and
turn the socket clockwise.
License Plate Light Bulb
Replacement
OCN7080035
1. Using a flat-blade screwdriver gently
pry the lens co ver from the lamp
housing.
2.
Remo

ve the bulb by pulling it straight
out.
3.
Install a ne

w bulb.
4.
Reins

tall in the reverse order.

I
I -7
Instrument Cluster ........................................................................\
.........................4-4
Gauges and Meters ........................................................................\
.....................4-5
Instrument Cluster Control ........................................................................\
.........4-5
LCD Display Messages ........................................................................\
............ 4-19
Transmission shift indicator ........................................................................\
.......4-9
Warning and Indicator Lights ........................................................................\
.....4-9
Instrument Panel Overview
........................................................................\
........... 2-5
Intelligent Speed Limit

Assist (ISLA)
................................................................ 7-66
Function malfunction and limitations ..............................................................7-69
Function operation ........................................................................\
.................... 7-67
Function settings ........................................................................\
...................... 7-66
Intelligent

Variable Transmission
........................................................................\
6-12
Good driving practices ........................................................................\
............. 6-18
Intelligent variable transmission operation ......................................................6-12
Parking ........................................................................\
..................................... 6-17
Interior Features
........................................................................\
......................... 5

-111
Clock ........................................................................\
......................................5-1

16
Clothes Hanger ........................................................................\
.......................5-1

16
Cup Holder ........................................................................\
.............................5

-111
Power Outlet ........................................................................\
...........................5-1

12
Sunvisor ........................................................................\
..................................5-1

12
USB Charger ........................................................................\
..........................5-1

13
Wireless Cellular Phone Char

ging System
..................................................... 5-1

14
Interior Lights
........................................................................\
.............................. 5-75
Front lamps ........................................................................\
............................... 5-75
Interior lamp AUT

O cut
........................................................................\
........... 5-75
Luggage compartment lamp ........................................................................\
.....5-77
Rear lamp ........................................................................\
................................. 5-76
Vanity mirror lamp ........................................................................\
...................5-77
Welcome system ........................................................................\
....................... 5-78
Interior Overview

........................................................................\
........................... 2-4
ISG (Idle Stop and Go) system
........................................................................\
.... 6-35
Battery Sensor Deactivation ........................................................................\
..... 6-38
ISG System Malfunction ........................................................................\
.......... 6-37
To

Activate the ISG System
........................................................................\
..... 6-35
To Deactivate the ISG System ........................................................................\
6-37