lock HYUNDAI ELANTRA 2022 Owners Manual
[x] Cancel search | Manufacturer: HYUNDAI, Model Year: 2022, Model line: ELANTRA, Model: HYUNDAI ELANTRA 2022Pages: 584, PDF Size: 14.08 MB
Page 308 of 584
06
6-49
WARNING
If ESC indicator light () or EPS
warning light () stays on or blinks,
your vehicle may have a malfunction
with the VSM system. When the
warning light illuminates, have your
vehicle checked by an authorized
HYUNDAI dealer as soon as possible.
Driving with wheels and tires with
different sizes may cause the ESC system
to malfunction. Before replacing tires,
make sure all four tires and wheels are
the same size. Never drive the vehicle
with different sized tires and wheels
installed.
Hill-Start Assist Control (HAC)
(if equipped)
The Hill-Start Assist Control (HAC)
helps prevent the vehicle from rolling
backwards when starting a vehicle from
a stop on a hill. The system operates the
brakes automatically for approximately
2 seconds and releases the brake after 2
seconds or when the accelerator pedal is
depressed.
WARNING
Always be ready to depress the
accelerator pedal when starting off on
a incline. The HAC activates only for
approximately 2 seconds.
NOTICE
[ The HAC does not operate when
the shift button is in P (Park) or N
(Neutral)
[ The HAC activates even though the
ESC (Electronic Stability Control) is
off but does not activate when the
ESC has malfunctioned.
Good Braking Practices
WARNING
Whenever leaving the vehicle or
parking, always come to a complete
stop and continue to depress the brake
pedal. Move the shift button into P
(Park) position, then apply the parking
brake, and place the ignition switch in
the LOCK/OFF position.
Vehicles parked with the parking brake
not applied or not fully engaged may
roll inadvertently and may cause injury
to the driver and others. ALWAYS apply
the parking brake before exiting the
vehicle.
Wet brakes can be dangerous! The
brakes may get wet if the vehicle is
driven through standing water or if it
is washed. Your vehicle will not stop as
quickly if the brakes are wet. Wet brakes
may cause the vehicle to pull to one side.
To dry the brakes, apply the brakes
lightly until the braking action returns to
normal, taking care to keep the vehicle
under control at all times. If the braking
action does not return to normal, stop
as soon as it is safe to do so and call
an authorized HYUNDAI dealer for
assistance.
DO NOT drive with your foot resting on
the brake pedal. Even light, but constant
pedal pressure can result in the brakes
overheating, brake wear, and possibly
even brake failure.
If a tire goes flat while you are driving,
apply the brakes gently and keep the
vehicle pointed straight ahead while you
slow down. When you are moving slowly
enough for it to be safe to do so, pull off
the road and stop in a safe location.
Keep your foot firmly on the brake pedal
when the vehicle is stopped to prevent
the vehicle from rolling forward.
Page 311 of 584
While Driving
6-52
OIK057086N
The auto start is temporarily deactivated
in the following situations.
When the gear is shifted from N (Neutral)
to R (Reverse), D (Drive) or Manual
shift mode without the brake pedal
depressed. A message "Press brake pedal
for Auto Start" will appear on the LCD
display. To activate auto start, depress
the brake pedal.
To Deactivate the ISG System
[ Press the ISG OFF button to
deactivate the ISG system. Then, the
ISG OFF button indicator illuminates.
[ Press the ISG OFF button again to
reactivate the ISG system. Then, the
ISG OFF button indicator turns OFF.
ISG System Malfunction
The ISG system may not operate:
When there is a malfunction with the ISG
sensors or the ISG system.
The following occurs, when there is a
malfunction with the ISG system:
[ The auto stop indicator () will
illuminate in yellow on the instrument
cluster.
[ The light on the ISG OFF button will
illuminate.
Information
[ When you cannot turn OFF the ISG
OFF button indicator by pressing
the ISG OFF button, or when the
malfunction with the ISG system
persists, contact an authorized
HYUNDAI dealer.
[ You can turn off the ISG OFF button
indicator by driving over 50 mph (80
km/h) for up to 2 hours with the fan
speed below the 2nd position. If the
ISG OFF button indicator remains
ON, contact an authorized HYUNDAI
dealer.
WARNING
When the engine is in auto stop mode,
the engine may restart. Before leaving
the vehicle or checking the engine
compartment, stop the engine placing
the ignition switch to the LOCK/OFF
position or remove the ignition key.
Page 321 of 584
While Driving
6-62
WARNING
The use of tire chains may adversely
affect vehicle handling:
[ Drive less than 20 mph (30 km/h)
or the chain manufacturer's
recommended speed limit,
whichever is lower.
[ Drive carefully and avoid bumps,
holes, sharp turns, and other road
hazards, which may cause the
vehicle to bounce.
[ Avoid sharp turns or locked wheel
braking.
CAUTION
If your vehicle has 235/40R18 size tires,
do not use tire chain; they can damage
your vehicle (wheel, suspension and
body).
Information
[ Install tire chains on both left and right
front tires. It should be noted that
installing tire chains on the tires will
provide a greater driving force, but will
not prevent side skids.
[ Do not install studded tires without
first checking local, state and municipal
regulations for possible restrictions
against their use.
Chain installation
When installing tire chains, follow the
manufacturer’s instructions and mount
them as tightly possible. Drive slowly
(less than 20 mph (30 km/h)) with
chains installed. If you hear the chains
contacting the body or chassis, stop and
tighten them. If they still make contact,
slow down until the noise stops. Remove
the tire chains as soon as you begin
driving on cleared roads.
When mounting snow chains, park the
vehicle on level ground away from traffic.
Turn on the vehicle Hazard Warning
Flasher and place a triangular emergency
warning device behind the vehicle (if
available). Always place the vehicle in P
(Park), apply the parking brake and turn
off the engine before installing snow
chains.
NOTICE
When using tire chains:
[ Wrong size chains or improperly
installed chains can damage your
vehicle's brake lines, suspension,
body and wheels.
[ Use SAE "S" class or wire chains.
[ If you hear noise caused by chains
contacting the body, retighten the
chain to prevent contact with the
vehicle body.
[ To prevent body damage, retighten
the chains after driving 0.3~0.6 miles
(0.5~1.0 km).
[ Do not use tire chains on vehicles
equipped with aluminum wheels. If
unavoidable, use a wire type chain.
[ Use wire chains less than 0.59 inch
(15mm) wide to prevent damage to
the chain’s connection.
Page 322 of 584
06
6-63
Winter Precautions
Use high quality ethylene glycol
coolant
Your vehicle is delivered with high
quality ethylene glycol coolant in the
cooling system. It is the only type of
coolant that should be used because it
helps prevent corrosion in the cooling
system, lubricates the water pump and
prevents freezing. Be sure to replace or
replenish your coolant in accordance
with the maintenance schedule in
chapter 8. Before winter, have your
coolant tested to assure that its freezing
point is sufficient for the temperatures
anticipated during the winter.
Change to "winter weight" oil if
necessary
In some climates it is recommended that
a lower viscosity "winter weight" oil be
used during cold weather. See chapter 8
for recommendations. If you aren't sure
what weight oil you should use, consult
an authorized HYUNDAI dealer.
Check battery and cables
Winter puts additional burdens on the
battery system. Visually inspect the
battery and cables as described in
chapter 8. The level of charge in your
battery can be checked by an authorized
HYUNDAI dealer or a service station.
Check spark plugs and ignition
system
Inspect your spark plugs as described in
chapter 8 and replace them if necessary.
Also check all ignition wiring and
components to be sure they are not
cracked, worn or damaged in any way.
Use approved window washer anti-
freeze in system
To keep the water in the window washer
system from freezing, add an approved
window washer anti-freeze solution in
accordance with instructions on the
container. Window washer anti-freeze is available
from an authorized HYUNDAI dealer
and most auto parts outlets. Do not
use engine coolant or other types of
antifreeze as these may damage the
paint finish.
Do not let your parking brake freeze
Under some conditions your parking
brake can freeze in the engaged position.
This is most likely to happen when
there is an accumulation of snow or
ice around or near the rear brakes or
if the brakes are wet. If there is a risk
the parking brake may freeze, apply
it only temporarily while you put the
gear selector lever in P and block the
rear wheels so the car cannot roll. Then
release the parking brake.
Do not let ice and snow accumulate
underneath
Under some conditions, snow and ice
can build up under the fenders and
interfere with the steering. When driving
in severe winter conditions where this
may happen, you should periodically
check underneath the car to be sure the
movement of the front wheels and the
steering components is not obstructed.
Don't place foreign objects
or materials in the engine
compartment
Placement of foreign object or materials
which prevent cooling of the engine, in
the engine compartment, may cause a
failure or combustion. The manufacturer
is not responsible for the damage caused
by such placement.
To keep locks from freezing
To keep the locks from freezing, squirt
an approved de-icer fluid or glycerine
into the key opening. If a lock is covered
with ice, squirt it with an approved de-
icing fluid to remove the ice. If the lock
is frozen internally, you may be able to
thaw it out by using a heated key. Handle
the heated key with care to avoid injury.
Page 337 of 584
07
7-9
[ Driving through steam, smoke or
shadow
[ Only part of the vehicle, pedestrian or
cyclist is detected
[ The vehicle in front is a bus, heavy
truck, truck with a unusually shaped
luggage, trailer, etc.
[ The vehicle in front has no tail lights,
tail lights are located unusually, etc.
[ The brightness outside is low, and the
tail lamps are not on or are not bright
[ The rear of the front vehicle is small
or the vehicle does not look normal,
such as when the vehicle is tilted,
overturned, or the side of the vehicle
is visible, etc.
[ 7 K H I U R Q W Y H K L F O HT V J U R X Q G F O H D U D Q F H L V
low or high
[ A vehicle or pedestrian suddenly cuts
in front
[ The vehicle in front is detected late
[ The vehicle in front is suddenly
blocked by a obstacle
[ The vehicle in front suddenly changes
lane or suddenly reduces speed
[ The vehicle in front is bent out of
shape
[ 7 K H I U R Q W Y H K L F O HT V V S H H G L V I D V W R U
slow
[ The vehicle in front steers in the
opposite direction of your vehicle to
avoid a collision
[ With a vehicle in front, your vehicle
changes lane at low speed
[ The vehicle in front is covered with
snow[ You are departing or returning to the
lane
[ Unstable driving
[ You are on a roundabout and the
vehicle in front is not detected
[ You are continuously driving in a circle
[ The vehicle in front has an unusual
shape
[ The vehicle in front is driving uphill or
downhill
[ The pedestrian is not fully detected,
for example, if the pedestrian is
leaning over or is not fully walking
upright
[ The pedestrian is wearing clothing or
equipment that makes it difficult to
detect as a pedestrian
OADAS051
The illustration above shows the image
the front view camera will detect as a
vehicle and pedestrian.
[ The pedestrian in front is moving very
quickly
[ The pedestrian in front is short or is
posing a low posture
[ The pedestrian in front has impaired
mobility
[ The pedestrian in front is moving
intersected with the driving direction
Page 352 of 584
Driver assistance system
7-24
[ Your vehicle is being towed
[ The surrounding is very bright
[ The surrounding is very dark, such as
in a tunnel, etc.
[ The brightness changes suddenly, for
example when entering or exiting a
tunnel
[ The brightness outside is low, and the
headlamps are not on or are not bright
[ Driving through steam, smoke or
shadow
[ Only part of the vehicle, pedestrian or
cyclist is detected
[ The vehicle in front is a bus, heavy
truck, truck with a unusually shaped
luggage, trailer, etc.
[ The vehicle in front has no tail lights,
tail lights are located unusually, etc.
[ The brightness outside is low, and the
tail lamps are not on or are not bright
[ The rear of the front vehicle is small
or the vehicle does not look normal,
such as when the vehicle is tilted,
overturned, or the side of the vehicle
is visible, etc.
[ 7 K H I U R Q W Y H K L F O HT V J U R X Q G F O H D U D Q F H L V
low or high
[ A vehicle, pedestrian or cyclist
suddenly cuts in front
[ The bumper around the front radar is
impacted, damaged or the front radar
is out of position
[ The temperature around the front
radar is high or low[ Driving through a tunnel or iron bridge
[ Driving in large areas where there are
few vehicles or structures (i.e. desert,
meadow, suburb, etc.)
[ Driving near areas containing metal
substances, such as a construction
zone, railroad, etc.
[ A material is near that reflects very
well on the front radar, such as a
guardrail, nearby vehicle, etc.
[ The cyclist in front is on a bicycle
made of material that does not reflect
on the front radar
[ The vehicle in front is detected late
[ The vehicle in front is suddenly
blocked by a obstacle
[ The vehicle in front suddenly changes
lane or suddenly reduces speed
[ The vehicle in front is bent out of
shape
[ 7 K H I U R Q W Y H K L F O HT V V S H H G L V I D V W R U
slow
[ The vehicle in front steers in the
opposite direction of your vehicle to
avoid a collision
[ With a vehicle in front, your vehicle
changes lane at low speed
[ The vehicle in front is covered with
snow
[ You are departing or returning to the
lane
[ Unstable driving
[ You are on a roundabout and the
vehicle in front is not detected
[ You are continuously driving in a circle
[ The vehicle in front has an unusual
shape
[ The vehicle in front is driving uphill or
downhill
Page 371 of 584
07
7-43
WARNING
[ Even though the warning message
does not appear on the cluster, Blind-
Spot Safety system may not properly
operate.
[ Blind-Spot Safety system may not
properly operate in an area (e.g. open
terrain), where any substance are
not detected right after the engine
is turned on, or when the detecting
sensor is blocked with foreign
material right after the engine is
turned on.
CAUTION
Turn off Blind-Spot Safety system to
install a trailer, carrier, etc., or remove
the trailer, carrier, etc. to use Blind-Spot
Safety system.
Limitations of the function
Blind-Spot Safety system may not
operate normally, or the system may
operate unexpectedly under the
following circumstances:
[ There is inclement weather, such as
heavy snow, heavy rain, etc.
[ The rear corner radar is covered with
snow, rain, dirt, etc.
[ The temperature around the rear
corner radar is high or low
[ Driving on a highway (or motorway)
ramp
[ The road pavement (or the peripheral
ground) abnormally contains metallic
components (i.e. possibly due to
subway construction)[ There is a fixed object near the
vehicle, such as sound barriers,
guardrails, central dividers, entry
barriers, street lamps, signs,
tunnels, walls, etc. (including double
structures)
[ Driving in large areas where there are
few vehicles or structures (i.e. desert,
meadow, suburb, etc.)
[ Driving through a narrow road where
trees or grass are overgrown
[ Driving on a wet road surface, such as
a puddle on the road
[ The other vehicle drives very close
behind your vehicle, or the other
vehicle passes by your vehicle in close
proximity
[ The speed of the other vehicle is very
fast that it passes by your vehicle in a
short time
[ Your vehicle passes by the other
vehicle
[ Your vehicle changes lane
[ Your vehicle has started at the same
time as the vehicle next to you and
has accelerated
[ The vehicle in the next lane moves
two lanes away from you, or when the
vehicle two lanes away moves to the
next lane from you
[ A trailer or carrier is installed around
the rear corner radar
[ The bumper around the rear corner
radar is covered with objects, such as
a bumper sticker, bumper guard, bike
rack, etc.
[ The bumper around the rear corner
radar is impacted, damaged or the
radar is out of position
[ Your vehicle height is low or high
due to heavy loads, abnormal tire
pressure, etc.
Page 383 of 584
07
7-55
Function malfunction and
limitations
Function malfunction
OTM070099N
When Blind-Spot Safety system is not
working properly, the ‘Check Blind-Spot
6 D I H W \ V \ V W H P V T Z D U Q L Q J P H V V D J H Z L O O
appear on the cluster, and the system
will turn off automatically or the system
will be limited. We recommend that the
system be inspected by an authorized
HYUNDAI dealer.
OTM070100N
When the outside rearview mirror
warning light is not working properly, the
S & K H F N V L G H Y L H Z P L U U R U Z D U Q L Q J O L J K WT
warning message will appear on the
cluster. We recommend that the system
be inspected by an authorized HYUNDAI
dealer.
Function disabled
OTM070098N
When the rear bumper around the rear
corner radar or sensor is covered with
foreign material, such as snow or rain,
or installing a trailer or carrier, it can
reduce the detecting performance and
temporarily limit or disable Blind-Spot
Safety system.
If this occurs, the ‘Blind-Spot Safety
V \ V W H P V G L V D E O H G 5 D G D U E O R F N H GT
warning message will appear on the
cluster.
The function will operate normally
when such foreign material or trailer,
etc. is removed, and then the engine is
restarted.
If the function does not operate normally
after it is removed, we recommend
that the system be inspected by an
authorized HYUNDAI dealer.
WARNING
[ Even though the warning message
does not appear on the cluster, Blind-
Spot Safety system may not properly
operate.
[ Blind-Spot Safety system may not
properly operate in an area (e.g. open
terrain) where any substance are
not detected right after the engine
is turned on, or when the detecting
sensor is blocked with foreign
material right after the engine is
turned on.
Page 391 of 584
07
7-63
WARNING
Take the following precautions when
using Safe Exit Warning:
[ For your safety, change the Settings
after parking the vehicle at a safe
location.
[ If any other function’s warning
message is displayed or audible
warning is generated, Safe Exit
Warning warning message may not
be displayed and audible warning
may not be generated.
[ You may not hear the warning
sound of Safe Exit Warning if the
surrounding is noisy.
[ Safe Exit Warning does not operate
in all situations or cannot prevent all
collisions.
[ Safe Exit Warning may warn the
driver late or may not warn the driver
depending on the road and driving
conditions. Always check vehicle
surroundings.
[ The driver and passengers are
responsible for accidents that occurs
while exiting the vehicle. Always
check the surroundings before you
exit the vehicle.
[ Never deliberately operate Safe
Exit Warning. Doing so may lead to
serious injury or death.
[ Safe Exit Warning does not operate
if there is a problem with Blind-Spot
Safety system. The warning message
of Blind-Spot Safety system will
appear when:
-Blind-Spot Safety system sensor or
the sensor surrounding is polluted
or covered
-Blind-Spot Safety system fails to
warn passengers or falsely warn
passengers
Information
After the engine is turned off, Safe Exit
Warning operates approximately for 10
minutes, but turns off immediately if the
doors are locked.
Function malfunction and
limitations
Function malfunction
OCN7070039L
When Safe Exit Warning is not working
properly, the ‘Check Blind-Spot Safety
V \ V W H PT Z D U Q L Q J P H V V D J H Z L O O D S S H D U
on the cluster, and the system will turn
off automatically or the system will be
limited. We recommend that the system
be inspected by an authorized HYUNDAI
dealer.
Page 392 of 584
Driver assistance system
7-64
Function disabled
OCN7070041L
When the rear bumper around the rear
corner radar or sensor is covered with
foreign material, such as snow or rain,
or installing a trailer or carrier, it can
reduce the detecting performance and
temporarily limit or disable Safe Exit
Warning.
If this occurs, the ‘Blind-Spot Safety
I X Q F W L R Q G L V D E O H G 5 D G D U E O R F N H GT
warning message will appear on the
cluster.
The function will operate normally
when such foreign material or trailer,
etc. is removed, and then the engine is
restarted.
If the function does not operate normally
after it is removed, we recommend
that the system be inspected by an
authorized HYUNDAI dealer.
WARNING
[ Even though the warning message
does not appear on the cluster,
Safe Exit Warning may not properly
operate.
[ Safe Exit Warning may not properly
operate in an area (e.g. open
terrain) where any substance are
not detected right after the engine
is turned on, or when the detecting
sensor is blocked with foreign
material right after the engine is
turned on.
CAUTION
Turn off Safe Exit Warning to install
a trailer, carrier, etc., or remove the
trailer, carrier, etc. to use Safe Exit
Warning.
Limitations of the function
Safe Exit Warning may not operate
normally, or the function may operate
unexpectedly under the following
circumstances:
[ Getting off the vehicle where trees or
grass are overgrown
[ Getting off the vehicle where the road
is wet
[ The approaching vehicle is very fast or
very slow
WARNING
[ Safe Exit Warning may not operate
normally if interfered by strong
electromagnetic waves.
[ Safe Exit Warning may not operate
for 3 seconds after the vehicle is
started, or rear corner radars are
initialized.